CIRRUS CS4365_08

CS4365
114 dB, 192 kHz 6-Channel D/A Converter
Features
Description
 Advanced Multi-bit Delta Sigma Architecture
The CS4365 is a complete 6-channel digital-to-analog
system. This D/A system includes digital de-emphasis,
half-dB step size volume control, ATAPI channel mixing, selectable fast and slow digital interpolation filters
followed by an oversampled, multi-bit delta sigma modulator which includes mismatch-shaping technology
that eliminates distortion due to capacitor mismatch.
Following this stage is a multi-element switched capacitor stage and low-pass filter with differential analog
outputs.
 24-bit Conversion
 Automatic Detection of Sample Rates up to
192 kHz
 114 dB Dynamic Range
 -100 dB THD+N
 Direct Stream Digital Mode
–
–
–
Non-Decimating Volume Control
On-Chip 50 kHz Filter
Matched PCM and DSD Analog Output
Levels
 Selectable Digital Filters
 Volume Control with 1/2-dB Step Size and Soft
Ramp
 Low Clock-Jitter Sensitivity
 +5 V Analog Supply, +2.5 V Digital Supply
 Separate 1.8 to 5 V Logic Supplies for the
Control and Serial Ports
Hardware Mode or
I2C/SPI Software Mode
Control Data
Reset
Level Translator
Control Port Supply = 1.8 V to 5 V
The CS4365 also has a proprietary DSD processor
which allows for volume control and 50 kHz on-chip filtering without an intermediate decimation stage. It also
offers an optional path for direct DSD conversion by directly using the multi-element switched capacitor array.
The CS4365 is available in a 48-pin LQFP package in
both Commercial (-40°C to +85°C) and Automotive
(-40°C to +105°C) grades. The CDB4365 Customer
Demonstration board is also available for device evaluation and implementation suggestions. Please see
“Ordering Information” on page 51 for complete details.
The CS4365 accepts PCM data at sample rates from
4 kHz to 216 kHz, DSD audio data, and delivers excellent sound quality. These features are ideal for multichannel audio systems, including SACD players, A/V
receivers, digital TV’s, mixing consoles, effects processors, sound cards, and automotive audio systems.
Digital Supply = 2.5 V
Analog Supply = 5 V
Internal Voltage
Reference
Register/Hardware
Configuration
Serial Audio Port
Supply = 1.8 V to 5 V
DSD Audio
Input
http://www.cirrus.com
Serial Interface
PCM Serial
Audio Input
Level Translator
6
Volume
Controls
Digital
Filters
DSD Processor
-Volume control
-50 kHz filter
Multi-bit ΔΣ
Modulators
Switch-Cap
DAC and
Analog Filters
External Mute
Control
Copyright © Cirrus Logic, Inc. 2008
(All Rights Reserved)
6
6
6
Six Channels of
Differential
Outputs
Mute Signals
FEB '08
DS670F2
CS4365
TABLE OF CONTENTS
1. PIN DESCRIPTION ................................................................................................................................ 6
2. CHARACTERISTICS AND SPECIFICATIONS ...................................................................................... 8
RECOMMENDED OPERATING CONDITIONS ..................................................................................... 8
ABSOLUTE MAXIMUM RATINGS ......................................................................................................... 8
DAC ANALOG CHARACTERISTICS - COMMERCIAL (-CQZ) ............................................................. 9
DAC ANALOG CHARACTERISTICS - AUTOMOTIVE (-DQZ) ............................................................ 10
POWER AND THERMAL CHARACTERISTICS .................................................................................. 11
COMBINED INTERPOLATION & ON-CHIP ANALOG FILTER RESPONSE ...................................... 12
COMBINED INTERPOLATION & ON-CHIP ANALOG FILTER RESPONSE (CONTINUED) .............. 13
DSD COMBINED DIGITAL & ON-CHIP ANALOG FILTER RESPONSE ............................................. 13
DIGITAL CHARACTERISTICS ............................................................................................................. 14
SWITCHING CHARACTERISTICS - PCM ........................................................................................... 15
SWITCHING CHARACTERISTICS - DSD ........................................................................................... 16
SWITCHING CHARACTERISTICS - CONTROL PORT - I²C FORMAT .............................................. 17
SWITCHING CHARACTERISTICS - CONTROL PORT - SPI FORMAT ............................................. 18
3. TYPICAL CONNECTION DIAGRAM .................................................................................................. 19
4. APPLICATIONS ................................................................................................................................... 21
4.1 Master Clock ................................................................................................................................... 21
4.2 Mode Select .................................................................................................................................... 22
4.3 Digital Interface Formats ................................................................................................................ 23
4.3.1 OLM #1 .................................................................................................................................. 24
4.3.2 OLM #2 .................................................................................................................................. 24
4.4 Oversampling Modes ...................................................................................................................... 24
4.5 Interpolation Filter ........................................................................................................................... 25
4.6 De-Emphasis .................................................................................................................................. 25
4.7 ATAPI Specification ........................................................................................................................ 26
4.8 Direct Stream Digital (DSD) Mode .................................................................................................. 26
4.9 Grounding and Power Supply Arrangements ................................................................................. 27
4.9.1 Capacitor Placement ............................................................................................................. 27
4.10 Analog Output and Filtering .......................................................................................................... 28
4.11 The MUTEC Outputs .................................................................................................................... 29
4.12 Recommended Power-Up Sequence ........................................................................................... 29
4.12.1 Hardware Mode ................................................................................................................... 29
4.12.2 Software Mode .................................................................................................................... 30
4.13 Recommended Procedure for Switching Operational Modes ....................................................... 30
4.14 Control Port Interface ................................................................................................................... 30
4.14.1 MAP Auto Increment ........................................................................................................... 30
4.14.2 I²C Mode .............................................................................................................................. 30
4.14.2.1 I²C Write ................................................................................................................... 31
4.14.2.2 I²C Read .................................................................................................................. 31
4.14.3 SPI Mode ............................................................................................................................. 32
4.14.3.1 SPI Write .................................................................................................................. 32
4.15 Memory Address Pointer (MAP) .................................................................................................. 32
4.15.1 INCR (Auto Map Increment Enable) .................................................................................... 32
4.15.2 MAP4-0 (Memory Address Pointer) .................................................................................... 32
5. REGISTER QUICK REFERENCE ....................................................................................................... 33
6. REGISTER DESCRIPTION .................................................................................................................. 34
6.1 Chip Revision (address 01h) ......................................................................................................... 34
6.1.1 Part Number ID (PART) [Read Only] .................................................................................... 34
6.2 Mode Control 1 (address 02h) ........................................................................................................ 34
6.2.1 Control Port Enable (CPEN) .................................................................................................. 34
6.2.2 Freeze Controls (FREEZE) ................................................................................................... 34
2
DS670F2
CS4365
6.2.3 PCM/DSD Selection (DSD/PCM) .......................................................................................... 35
6.2.4 DAC Pair Disable (DACx_DIS) .............................................................................................. 35
6.2.5 Power Down (PDN) ............................................................................................................... 35
6.3 PCM Control (address 03h) ............................................................................................................ 35
6.3.1 Digital Interface Format (DIF) ................................................................................................ 35
6.3.2 Functional Mode (FM) ........................................................................................................... 36
6.4 DSD Control (address 04h) ............................................................................................................ 36
6.4.1 DSD Mode Digital Interface Format (DSD_DIF) .................................................................... 36
6.4.2 Direct DSD Conversion (DIR_DSD) ...................................................................................... 37
6.4.3 Static DSD Detect (STATIC_DSD) ........................................................................................ 37
6.4.4 Invalid DSD Detect (INVALID_DSD) ..................................................................................... 37
6.4.5 DSD Phase Modulation Mode Select (DSD_PM_MODE) ..................................................... 37
6.4.6 DSD Phase Modulation Mode Enable (DSD_PM_EN) ......................................................... 37
6.5 Filter Control (address 05h) ............................................................................................................ 38
6.5.1 Interpolation Filter Select (FILT_SEL) ................................................................................... 38
6.6 Invert Control (address 06h) ........................................................................................................... 38
6.6.1 Invert Signal Polarity (Inv_xx) ................................................................................................ 38
6.7 Group Control (address 07h) .......................................................................................................... 38
6.7.1 Mute Pin Control (MUTEC1, MUTEC0) ................................................................................. 38
6.7.2 Channel A Volume = Channel B Volume (Px_A=B) .............................................................. 39
6.7.3 Single Volume Control (SNGLVOL) ...................................................................................... 39
6.8 Ramp and Mute (address 08h) ....................................................................................................... 39
6.8.1 Soft Ramp and Zero Cross CONTROL (SZC) ...................................................................... 39
6.8.2 Soft Volume Ramp-Up after Error (RMP_UP) ....................................................................... 40
6.8.3 Soft Ramp-Down before Filter Mode Change (RMP_DN) ..................................................... 40
6.8.4 PCM Auto-Mute (PAMUTE) .................................................................................................. 40
6.8.5 DSD Auto-Mute (DAMUTE) ................................................................................................... 41
6.8.6 MUTE Polarity and DETECT (MUTEP1:0) ............................................................................ 41
6.9 Mute Control (address 09h) ............................................................................................................ 41
6.9.1 Mute (MUTE_xx) ................................................................................................................... 41
6.10 Mixing Control (address 0Ah, 0Dh, 10h, 13h) .............................................................................. 42
6.10.1 De-Emphasis Control (PX_DEM1:0) ................................................................................... 42
6.10.2 ATAPI Channel Mixing and Muting (ATAPI) ........................................................................ 42
6.11 Volume Control (address 0Bh, 0Ch, 0Eh, 0Fh, 11h, 12h) ............................................................ 43
6.11.1 Digital Volume Control (xx_VOL7:0) ................................................................................... 43
6.12 PCM Clock Mode (address 16h) .................................................................................................. 44
6.12.1 Master Clock DIVIDE by 2 ENABLE (MCLKDIV) ................................................................ 44
7. FILTER PLOTS ..................................................................................................................................... 45
8. PARAMETER DEFINITIONS ................................................................................................................ 49
9. PACKAGE DIMENSIONS ................................................................................................................... 50
10. ORDERING INFORMATION .............................................................................................................. 51
11. REFERENCES .................................................................................................................................... 51
12. REVISION HISTORY ......................................................................................................................... 51
DS670F2
3
CS4365
LIST OF FIGURES
Figure 1.Serial Audio Interface Timing ...................................................................................................... 15
Figure 2.Direct Stream Digital - Serial Audio Input Timing ........................................................................ 16
Figure 3.Direct Stream Digital - Serial Audio Input Timing for Phase Modulation Mode ........................... 16
Figure 4.Control Port Timing - I²C Format ................................................................................................. 17
Figure 5.Control Port Timing - SPI Format ................................................................................................ 18
Figure 6.Typical Connection Diagram, Software Mode ............................................................................. 19
Figure 7.Typical Connection Diagram, Hardware Mode ........................................................................... 20
Figure 8.Format 0 - Left-Justified up to 24-bit Data .................................................................................. 23
Figure 9.Format 1 - I²S up to 24-bit Data .................................................................................................. 23
Figure 10.Format 2 - Right-Justified 16-bit Data ....................................................................................... 23
Figure 11.Format 3 - Right-Justified 24-bit Data ....................................................................................... 23
Figure 12.Format 4 - Right-Justified 20-bit Data ....................................................................................... 23
Figure 13.Format 5 - Right-Justified 18-bit Data ....................................................................................... 24
Figure 14.Format 8 - One-Line Mode 1 ..................................................................................................... 24
Figure 15.Format 9 - One-Line Mode 2 ..................................................................................................... 24
Figure 16.De-Emphasis Curve .................................................................................................................. 25
Figure 17.ATAPI Block Diagram (x = channel pair 1, 2, or 3) ................................................................... 26
Figure 18.DSD Phase Modulation Mode Diagram .................................................................................... 27
Figure 19.Full-Scale Output ...................................................................................................................... 28
Figure 20.Recommended Output Filter ..................................................................................................... 28
Figure 21.Recommended Mute Circuitry .................................................................................................. 29
Figure 22.Control Port Timing, I²C Mode .................................................................................................. 31
Figure 23.Control Port Timing, SPI Mode ................................................................................................. 32
Figure 24.Single-Speed (fast) Stopband Rejection ................................................................................... 45
Figure 25.Single-Speed (fast) Transition Band ......................................................................................... 45
Figure 26.Single-Speed (fast) Transition Band (detail) ............................................................................. 45
Figure 27.Single-Speed (fast) Passband Ripple ....................................................................................... 45
Figure 28.Single-Speed (slow) Stopband Rejection ................................................................................. 45
Figure 29.Single-Speed (slow) Transition Band ........................................................................................ 45
Figure 30.Single-Speed (slow) Transition Band (detail) ............................................................................ 46
Figure 31.Single-Speed (slow) Passband Ripple ...................................................................................... 46
Figure 32.Double-Speed (fast) Stopband Rejection ................................................................................. 46
Figure 33.Double-Speed (fast) Transition Band ........................................................................................ 46
Figure 34.Double-Speed (fast) Transition Band (detail) ............................................................................ 46
Figure 35.Double-Speed (fast) Passband Ripple ...................................................................................... 46
Figure 36.Double-Speed (slow) Stopband Rejection ................................................................................ 47
Figure 37.Double-Speed (slow) Transition Band ...................................................................................... 47
Figure 38.Double-Speed (slow) Transition Band (detail) .......................................................................... 47
Figure 39.Double-Speed (slow) Passband Ripple .................................................................................... 47
Figure 40.Quad-Speed (fast) Stopband Rejection .................................................................................... 47
Figure 41.Quad-Speed (fast) Transition Band .......................................................................................... 47
Figure 42.Quad-Speed (fast) Transition Band (detail) .............................................................................. 48
Figure 43.Quad-Speed (fast) Passband Ripple ........................................................................................ 48
Figure 44.Quad-Speed (slow) Stopband Rejection ................................................................................... 48
Figure 45.Quad-Speed (slow) Transition Band ......................................................................................... 48
Figure 46.Quad-Speed (slow) Transition Band (detail) ............................................................................. 48
Figure 47.Quad-Speed (slow) Passband Ripple ....................................................................................... 48
4
DS670F2
CS4365
LIST OF TABLES
Table 1. Single-Speed Mode Standard Frequencies ................................................................................ 21
Table 2. Double-Speed Mode Standard Frequencies ............................................................................... 21
Table 3. Quad-Speed Mode Standard Frequencies ................................................................................. 21
Table 4. PCM Digital Interface Format, Hardware Mode Options ............................................................. 22
Table 5. Mode Selection, Hardware Mode Options .................................................................................. 22
Table 6. Direct Stream Digital (DSD), Hardware Mode Options ............................................................... 22
Table 7. Digital Interface Formats - PCM Mode ........................................................................................ 36
Table 8. Digital Interface Formats - DSD Mode ........................................................................................ 36
Table 9. ATAPI Decode Table .................................................................................................................. 42
Table 10. Example Digital Volume Settings .............................................................................................. 43
DS670F2
5
CS4365
AOUTB1-
AOUTB1+
AOUTA1+
AOUTA1-
DSD_SCLK
MUTEC1
TST
VLS
DSDB3
TST
DSDA3
DSDB2
1. PIN DESCRIPTION
48 47 46 45 44 43 42 41 40 39 38 37
DSDA2
1
36
DSDB1
2
35
AOUTA2+
DSDA1
3
AOUTB2+
VD
4
34
33
GND
5
32
31
VA
GND
AOUTA2-
AOUTB2-
MCLK
6
LRCK
7
30
AOUTA3-
SDIN1
8
29
SCLK
9
28
AOUTA3+
AOUTB3+
CS4365
M4(TST)
10
27
AOUTB3-
SDIN2
M3(TST)
11
26
MUTEC2
25
MUTEC3
12
Pin Name
VD
GND
#
4
MUTEC4
VQ
MUTEC6
MUTEC5
RST
FILT+
VLC
M0(AD0/CS)
M1(SDA/CDIN)
M2(SCL/CCLK)
TST
SDIN3
13 14 15 16 17 18 19 20 21 22 23 24
Pin Description
Digital Power (Input) - Positive power supply for the digital section. Refer to the Recommended Operating Conditions for appropriate voltages.
5, 31 Ground (Input) - Ground reference. Should be connected to analog ground.
MCLK
6
Master Clock (Input) - Clock source for the delta-sigma modulator and digital filters. Tables 1
through 3 illustrate several standard audio sample rates and the required master clock frequencies.
LRCK
7
Left Right Clock (Input) - Determines which channel, Left or Right, is currently active on the
serial audio data line. The frequency of the left/right clock must be at the audio sample rate, Fs.
SDIN1
SDIN2
SDIN3
8
11
13
Serial Data Input (Input) - Input for two’s complement serial audio data.
SCLK
9
Serial Clock (Input) - Serial clocks for the serial audio interface.
TST
14
44
45
Test - These pins need to be tied to analog ground.
RST
19
Reset (Input) - The device enters a low power mode and all internal registers are reset to their
default settings when low.
VA
32
Analog Power (Input) - Positive power supply for the analog section. Refer to the Recommended Operating Conditions for appropriate voltages.
VLS
43
Serial Audio Interface Power (Input) - Determines the required signal level for the serial audio
interface. Refer to the Recommended Operating Conditions for appropriate voltages.
VLC
18
Control Port Power (Input) - Determines the required signal level for the control port and
Hardware Mode configuration pins. Refer to the Recommended Operating Conditions for
appropriate voltages.
6
DS670F2
CS4365
Pin Name
#
Pin Description
VQ
21
Quiescent Voltage (Output) - Filter connection for internal quiescent voltage. VQ must be
capacitively coupled to analog ground, as shown in the Typical Connection Diagram. The nominal voltage level is specified in the Analog Characteristics and Specifications section. VQ presents an appreciable source impedance and any current drawn from this pin will alter device
performance. However, VQ can be used to bias the analog circuitry assuming there is no AC
signal component and the DC current is less then the maximum specified in the Analog Characteristics and Specifications section.
FILT+
20
Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling circuits. Requires the capacitive decoupling to analog ground as shown in the Typical Connection
Diagram.
AOUTA1 +,AOUTB1 +,AOUTA2 +,AOUTB2 +,AOUTA3 +,AOUTB3 +,MUTEC1
MUTEC2
MUTEC3
MUTEC4
MUTEC5
MUTEC6
39,40
37,38
35,36 Differential Analog Output (Output) - The full-scale differential analog output level is specified
33,34 in the Analog Characteristics specification table.
29,30
27,28
41
26
25
24
23
22
Mute Control (Output) - The Mute Control pins go high during power-up initialization, reset,
muting, power-down or if the master clock to left/right clock frequency ratio is incorrect. These
pins are intended to be used as a control for external mute circuits on the line outputs to prevent the clicks and pops that can occur in any single supply system. Use of Mute Control is not
mandatory but recommended for designs requiring the absolute minimum in extraneous clicks
and pops.
Hardware Mode Definitions
M0
M1
M2
M3
M4
17
16
15
12
10
Mode Selection (Input) - Determines the operational mode of the device as detailed in Table 6
and Table 7.
Software Mode Definitions
SCL/CCLK
15
Serial Control Port Clock (Input) - Serial clock for the serial control port. Requires an external
pull-up resistor to the logic interface voltage in I²C® Mode as shown in the Typical Connection
Diagram.
SDA/CDIN
16
Serial Control Port Data (Input/Output) - SDA is a data I/O line in I²C Mode and is open drain,
requiring an external pull-up resistor to the logic interface voltage, as shown in the Typical Connection Diagram; CDIN is the input data line for the control port interface in SPI™ Mode.
AD0/CS
17
Address Bit 0 (I²C) / Control Port Chip Select (SPI) (Input) - AD0 is a chip address pin in I²C
Mode; CS is the chip-select signal for SPI Mode.
TST
10, 12
Test - These pins need to be tied to analog ground.
DSD Definitions
DSDA1
DSDB1
DSDA2
DSDB2
DSDA3
DSDB3
3
2
1
48
47
46
Direct Stream Digital Input (Input) - Input for Direct Stream Digital serial audio data. GND if
unused.
DSD_SCLK
42
DSD Serial Clock (Input) - Serial clock for the Direct Stream Digital serial audio interface.
DS670F2
7
CS4365
2. CHARACTERISTICS AND SPECIFICATIONS
RECOMMENDED OPERATING CONDITIONS
GND = 0 V; all voltages with respect to ground.
Parameters
Symbol
Min
Typ
Max
Units
Analog power
Digital internal power
Serial data port interface power
Control port interface power
Ambient Operating Temperature (Power Applied)
Commercial Grade (-CQZ)
Automotive Grade (-DQZ)
VA
VD
VLS
VLC
4.75
2.37
1.71
1.71
5.0
2.5
5.0
5.0
5.25
2.63
5.25
5.25
V
V
V
V
TA
-40
-40
-
+ 85
+105
°C
°C
DC Power Supply
ABSOLUTE MAXIMUM RATINGS
GND = 0 V; all voltages with respect to ground.
Parameters
Symbol
Min
Max
Units
Analog power
Digital internal power
Serial data port interface power
Control port interface power
Input Current
Any Pin Except Supplies
Digital Input Voltage
Serial data port interface
Control port interface
Ambient Operating Temperature (Power Applied)
Storage Temperature
VA
VD
VLS
VLC
Iin
VIND-S
VIND-C
Top
Tstg
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-55
-65
6.0
3.2
6.0
6.0
±10
VLS+ 0.4
VLC+ 0.4
125
150
V
V
V
V
mA
V
V
°C
°C
DC Power Supply
WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation
is not guaranteed at these extremes.
8
DS670F2
CS4365
DAC ANALOG CHARACTERISTICS - COMMERCIAL (-CQZ)
Test Conditions (unless otherwise specified): VA = VLS = VLC = 5 V; VD = 2.5 V; TA = 25°C; Full-scale 997 Hz
input sine wave (Note 1); Tested under max ac-load resistance; Valid with FILT+ and VQ capacitors as shown in
“Typical Connection Diagram” on page 19; Measurement Bandwidth 10 Hz to 20 kHz.
Parameters
Symbol
Min
Typ
Max
Unit
108
105
-
114
111
97
94
-
dB
dB
dB
dB
-
-100
-91
-51
-94
-74
-34
-94
-45
-
dB
dB
dB
dB
dB
dB
A-weighted
-
114
-
dB
(1 kHz)
-
110
-
dB
Fs = 48 kHz, 96 kHz, 192 kHz and DSD
Dynamic Range
24-bit
A-weighted
unweighted
16-bit A-weighted
(Note 2) unweighted
Total Harmonic Distortion + Noise
(Note 2) 16-bit
Idle Channel Noise / Signal-to-noise ratio
Interchannel Isolation
24-bit
0 dB
-20 dB
-60 dB THD+N
0 dB
-20 dB
-60 dB
DC Accuracy
Interchannel Gain Mismatch
-
0.1
-
dB
Gain Drift
-
100
-
ppm/°
C
VFS
1.28•VA
0.90•VA
1.32•VA
0.94•VA
1.36•VA
0.98•VA
Vpp
Vpp
ZOUT
-
130
-
Ω
IOUTmax
-
1.0
-
mA
RL
-
3
-
kΩ
Max Load Capacitance
CL
-
100
-
pF
Quiescent Voltage
VQ
-
50% VA
-
VDC
IQMAX
-
10
-
μA
Analog Output
Full-Scale DifferentialOutput Voltage (Note 3)
PCM, DSD processor
Direct DSD Mode
Output Impedance
Max DC Current draw from an AOUT pin
Min AC-Load Resistance
Max Current draw from VQ
Notes:
1.
One-half LSB of triangular PDF dither is added to data.
2. Performance limited by 16-bit quantization noise.
3. VFS is tested under load RL and includes attenuation due to ZOUT.
DS670F2
9
CS4365
DAC ANALOG CHARACTERISTICS - AUTOMOTIVE (-DQZ)
Test Conditions (unless otherwise specified): VA = 4.75 to 5.25 V; VLS = 1.71 to 5.25 V; VLC = 1.71 to 5.25 V;
VD = 2.37 to 2.63 V; TA = -40°C to 85°C; Full-scale 997 Hz input sine wave (Note 1); Tested under max ac-load
resistance; Valid with FILT+ and VQ capacitors as shown in “Typical Connection Diagram” on page 19; Measurement Bandwidth 10 Hz to 20 kHz.
Parameters
Fs = 48 kHz, 96 kHz, 192 kHz and DSD
Dynamic Range (Note 1)
Symbol
24-bit
A-weighted
unweighted
16-bit A-weighted
(Note 2) unweighted
Total Harmonic Distortion + Noise
(Note 1)
24-bit
0 dB
-20 dB
-60 dB THD+N
(Note 2) 16-bit
0 dB
-20 dB
-60 dB
Idle Channel Noise / Signal-to-noise ratio
A-weighted
Interchannel Isolation
(1 kHz)
Min
Typ
Max
Units
105
102
-
114
111
97
94
-
dB
dB
dB
dB
-
-100
-91
-51
-94
-74
-34
114
110
-91
-42
-
dB
dB
dB
dB
dB
dB
dB
dB
-
0.1
100
-
dB
ppm/°C
1.28•VA
0.90•VA
-
1.32•VA
0.94•VA
130
1.0
3
100
50% VA
10
1.36•VA
0.98•VA
-
Vpp
Vpp
Ω
mA
kΩ
pF
VDC
μA
DC Accuracy
Interchannel Gain Mismatch
Gain Drift
Analog Output
Full-Scale DifferentialPCM, DSD processor
VFS
Output Voltage (Note 3)
Direct DSD Mode
Output Impedance
ZOUT
Max DC Current draw from an AOUT pin
IOUTmax
Min AC-Load Resistance
RL
Max Load Capacitance
CL
Quiescent Voltage
VQ
Max Current draw from VQ
IQMAX
10
DS670F2
CS4365
POWER AND THERMAL CHARACTERISTICS
Parameters
Symbol
Min
Typ
Max
Units
normal operation, VA= 5 V
VD= 2.5 V
(Note 5) Interface current, VLC=5 V
VLS=5 V
(Note 6) power-down state (all supplies)
Power Dissipation (Note 4)
VA = 5 V, VD = 2.5 V
normal operation
(Note 6) power-down
Package Thermal Resistance
multi-layer
dual-layer
IA
ID
ILC
ILS
Ipd
-
60
16
2
84
200
65
22
-
mA
mA
μA
μA
μA
θJA
θJA
θJC
-
340
1
48
65
15
60
40
390
-
mW
mW
°C/Watt
°C/Watt
°C/Watt
dB
dB
Power Supplies
Power Supply Current
(Note 4)
Power Supply Rejection Ratio (Note 7)
(1 kHz)
(60 Hz)
PSRR
Notes:
4. Current consumption increases with increasing Fs within a given speed mode and is signal dependent.
Max values are based on highest Fs and highest MCLK.
5. ILC measured with no external loading on the SDA pin.
6. Power-Down Mode is defined as RST pin = Low with all clock and data lines held static.
7. Valid with the recommended capacitor values on FILT+ and VQ as shown in Figures 6 and 7.
DS670F2
11
CS4365
COMBINED INTERPOLATION & ON-CHIP ANALOG FILTER RESPONSE
The filter characteristics have been normalized to the sample rate (Fs) and can be referenced to the desired sample rate by multiplying the given characteristic by Fs. See Note 12.
Fast Roll-Off
Parameter
Unit
Min
Typ
Max
Combined Digital and On-chip Analog Filter Response - Single-Speed Mode - 48 kHz
Passband (Note 9)
Frequency Response
to -0.01 dB corner
to -3 dB corner
10 Hz to 20 kHz
StopBand
StopBand Attenuation
(Note 10)
Group Delay
De-emphasis Error (Note 11)
(Relative to 1 kHz)
Fs = 32 kHz
Fs = 44.1 kHz
Fs = 48 kHz
0
0
-
.454
.499
Fs
Fs
-0.01
-
+0.01
dB
0.547
-
-
Fs
102
-
-
dB
-
10.4/Fs
-
s
-
-
±0.36
±0.21
±0.14
dB
dB
dB
Combined Digital and On-chip Analog Filter Response - Double-Speed Mode - 96 kHz
Passband (Note 9)
Frequency Response
to -0.01 dB corner
to -3 dB corner
10 Hz to 20 kHz
StopBand
StopBand Attenuation
(Note 10)
Group Delay
0
0
-
.430
.499
Fs
Fs
-0.01
-
+0.01
dB
.583
-
-
Fs
80
-
-
dB
-
6.15/Fs
-
s
Combined Digital and On-chip Analog Filter Response - Quad-Speed Mode - 192 kHz
Passband (Note 9)
Frequency Response
to -0.01 dB corner
to -3 dB corner
10 Hz to 20 kHz
StopBand
StopBand Attenuation
(Note 10)
Group Delay
0
0
-
.105
.490
Fs
Fs
-0.01
-
+0.01
dB
.635
-
-
Fs
90
-
-
dB
-
7.1/Fs
-
s
Notes:
8. Slow roll-off interpolation filter is only available in Software Mode.
9. Response is clock-dependent and will scale with Fs.
10. For Single-Speed Mode, the Measurement Bandwidth is from stopband to 3 Fs.
For Double-Speed Mode, the Measurement Bandwidth is from stopband to 3 Fs.
For Quad-Speed Mode, the Measurement Bandwidth is from stopband to 1.34 Fs.
11. De-emphasis is available only in Single-Speed Mode; only 44.1 kHz De-emphasis is available in Hardware Mode.
12. Amplitude vs. Frequency plots of this data are available in Section 7. “Filter Plots” on page 45.
12
DS670F2
CS4365
COMBINED INTERPOLATION & ON-CHIP ANALOG FILTER RESPONSE
(CONTINUED)
Slow Roll-Off (Note 8)
Parameter
Unit
Min
Typ
Max
0
0
-
0.417
0.499
Fs
Fs
-0.01
-
+0.01
dB
.583
-
-
Fs
64
-
-
dB
Single-Speed Mode - 48 kHz
Passband (Note 9)
to -0.01 dB corner
to -3 dB corner
Frequency Response
10 Hz to 20 kHz
StopBand
StopBand Attenuation
(Note 10)
Group Delay
De-emphasis Error (Note 11)
(Relative to 1 kHz)
-
7.8/Fs
-
s
Fs = 32 kHz
Fs = 44.1 kHz
Fs = 48 kHz
-
-
±0.36
±0.21
±0.14
dB
dB
dB
to -0.01 dB corner
to -3 dB corner
0
0
-
.296
.499
Fs
Fs
-0.01
-
+0.01
dB
.792
-
-
Fs
70
-
-
dB
-
5.4/Fs
-
s
0
0
-
.104
.481
Fs
Fs
-0.01
-
+0.01
dB
.868
-
-
Fs
75
-
-
dB
-
6.6/Fs
-
s
Double-Speed Mode - 96 kHz
Passband (Note 9)
Frequency Response
10 Hz to 20 kHz
StopBand
StopBand Attenuation
(Note 10)
Group Delay
Quad-Speed Mode - 192 kHz
Passband (Note 9)
to -0.01 dB corner
to -3 dB corner
Frequency Response
10 Hz to 20 kHz
StopBand
StopBand Attenuation
(Note 10)
Group Delay
DSD COMBINED DIGITAL & ON-CHIP ANALOG FILTER RESPONSE
Parameter
Min
Typ
Max
Unit
DSD Processor Mode
Passband (Note 9)
Frequency Response
to -3 dB corner
0
-
50
kHz
10 Hz to 20 kHz
-0.05
-
+0.05
dB
27
-
-
dB/Oct
0
0
-
26.9
176.4
kHz
kHz
-0.1
-
0
dB
Roll-off
Direct DSD Mode
Passband (Note 9)
Frequency Response 10 Hz to 20 kHz
DS670F2
to -0.1 dB corner
to -3 dB corner
13
CS4365
DIGITAL CHARACTERISTICS
Parameters
Input Leakage Current
Input Capacitance
High-Level Input Voltage
Min
Typ
Max
Units
Iin
8
-
±10
0.30•VLS
0.30•VLC
0.20•VLC
μA
pF
V
V
V
V
V
Serial I/O
Control I/O
Serial I/O
Control I/O
Control I/O = 3.3 V, 5 V
VIH
VIH
VIL
VIL
VOL
0.70•VLS
0.70•VLC
-
Low-Level Output Voltage (IOL = -1.2 mA) Control I/O = 1.8 V, 2.5 V
VOL
-
-
0.25•VLC
V
MUTEC auto detect input high voltage
MUTEC auto detect input low voltage
Maximum MUTEC Drive Current
MUTEC High-Level Output Voltage
MUTEC Low-Level Output Voltage
VIH
VIL
Imax
VOH
VOL
0.70•VA
-
3
VA
0
0.30•VA
-
V
V
mA
V
V
Low-Level Input Voltage
Low-Level Output Voltage (IOL = -1.2 mA)
(Note 13)
Symbol
Notes:
13. Any pin except supplies. Transient currents of up to ±100 mA on the input pins will not cause SCR latchup.
14
DS670F2
CS4365
SWITCHING CHARACTERISTICS - PCM
Inputs: Logic 0 = GND, Logic 1 = VLS, CL = 20 pF.
Parameters
Symbol
RST pin Low Pulse Width
(Note 14)
MCLK Frequency
MCLK Duty Cycle
(Note 15)
Min
Max
Units
1
-
ms
1.024
55.2
MHz
45
55
%
Input Sample Rate - LRCK (Manual selection)
Single-Speed Mode
Double-Speed Mode
Quad-Speed Mode
Fs
Fs
Fs
4
50
100
54
108
216
kHz
kHz
kHz
Input Sample Rate - LRCK (Auto detect)
Single-Speed Mode
Double-Speed Mode
Quad-Speed Mode
Fs
Fs
Fs
4
84
170
54
108
216
kHz
kHz
kHz
LRCK Duty Cycle
45
55
%
SCLK Duty Cycle
45
55
%
SCLK High Time
tsckh
8
-
ns
SCLK Low Time
tsckl
8
-
ns
LRCK Edge to SCLK Rising Edge
tlcks
5
-
ns
SCLK Rising Edge to LRCK Falling Edge
tlckd
5
-
ns
SDIN Setup Time Before SCLK Rising Edge
tds
3
-
ns
SDIN Hold Time After SCLK Rising Edge
tdh
5
-
ns
Notes:
14. After powering up, RST should be held low until after the power supplies and clocks are settled.
15. See Tables 1 - 3 for suggested MCLK frequencies.
16. MSB of CH1 is always the second SCLK rising edge following LRCK rising edge.
LRCK
tlcks
tsckh
tsckl
SCLK
tds
SDINx
tdh
MSB
MSB-1
Figure 1. Serial Audio Interface Timing
DS670F2
15
CS4365
SWITCHING CHARACTERISTICS - DSD
Logic 0 = GND; Logic 1 = VLS; CL = 20 pF.
Parameter
Symbol
MCLK Duty Cycle
DSD_SCLK Pulse Width Low
DSD_SCLK Pulse Width High
DSD_SCLK Frequency
tsclkl
tsclkh
(64x Oversampled)
(128x Oversampled)
DSD_A / _B valid to DSD_SCLK rising setup time
DSD_SCLK rising to DSD_A or DSD_B hold time
DSD clock to data transition (Phase Modulation Mode)
tsdlrs
tsdh
tdpm
Min
Typ
Max
Unit
40
160
160
1.024
2.048
20
20
-20
-
60
3.2
6.4
20
%
ns
ns
MHz
MHz
ns
ns
ns
t sclkh
t sclkl
DSD_SCLK
t sdlrs
t sdh
DSDxx
Figure 2. Direct Stream Digital - Serial Audio Input Timing
t dpm
t dpm
DSD_SCLK
(128Fs)
DSD_SCLK
(64Fs)
DSDxx
Figure 3. Direct Stream Digital - Serial Audio Input Timing for Phase Modulation Mode
16
DS670F2
CS4365
SWITCHING CHARACTERISTICS - CONTROL PORT - I²C FORMAT
Inputs: Logic 0 = GND, Logic 1 = VLC, CL = 20 pF.
Symbol
Min
Max
Unit
SCL Clock Frequency
Parameter
fscl
-
100
kHz
RST Rising Edge to Start
tirs
500
-
ns
Bus Free Time Between Transmissions
tbuf
4.7
-
µs
Start Condition Hold Time (prior to first clock pulse)
thdst
4.0
-
µs
Clock Low time
tlow
4.7
-
µs
Clock High Time
thigh
4.0
-
µs
Setup Time for Repeated Start Condition
tsust
4.7
-
µs
thdd
0
-
µs
tsud
250
-
ns
Rise Time of SCL and SDA
trc, trc
-
1
µs
Fall Time SCL and SDA
tfc, tfc
-
300
ns
Setup Time for Stop Condition
tsusp
4.7
-
µs
Acknowledge Delay from SCL Falling
tack
300
1000
ns
SDA Hold Time from SCL Falling
(Note 17)
SDA Setup time to SCL Rising
Notes:
17. Data must be held for sufficient time to bridge the transition time, tfc, of SCL.
RST
t irs
Stop
Repeated
Start
Start
Stop
SDA
t buf
t
t high
t hdst
tf
hdst
t susp
SCL
t
low
t
hdd
t sud
t sust
tr
Figure 4. Control Port Timing - I²C Format
DS670F2
17
CS4365
SWITCHING CHARACTERISTICS - CONTROL PORT - SPI FORMAT
Inputs: Logic 0 = GND, Logic 1 = VLC, CL = 20 pF.
Symbol
Min
Max
Unit
CCLK Clock Frequency
Parameter
fsclk
-
6
MHz
RST Rising Edge to CS Falling
tsrs
500
-
ns
tspi
500
-
ns
CS High Time Between Transmissions
tcsh
1.0
-
µs
CS Falling to CCLK Edge
tcss
20
-
ns
CCLK Low Time
tscl
66
-
ns
CCLK High Time
tsch
66
-
ns
CCLK Edge to CS Falling
(Note 18)
tdsu
40
-
ns
CCLK Rising to DATA Hold Time
(Note 19)
tdh
15
-
ns
Rise Time of CCLK and CDIN
(Note 20)
tr2
-
100
ns
Fall Time of CCLK and CDIN
(Note 20)
tf2
-
100
ns
CDIN to CCLK Rising Setup Time
Notes:
18. tspi is only needed before first falling edge of CS after RST rising edge. tspi = 0 at all other times.
19. Data must be held for sufficient time to bridge the transition time of CCLK.
20. For FSCK < 1 MHz.
RST
t srs
CS
t spi t css
t scl
t sch
t csh
CCLK
t r2
t f2
CDIN
t dsu t
dh
Figure 5. Control Port Timing - SPI Format
18
DS670F2
CS4365
3. TYPICAL CONNECTION DIAGRAM
+2.5 V
+5 V
1 µF
+
+
0.1 µF
0.1 µF
4
VD
1 µF
32
VA
220 Ω
6
7
PCM
Digital
Audio
Source
9
8
11
13
MCLK
AOUTA1+
LRCK
AOUTA1-
SCLK
SDIN1
AOUTB1+
SDIN2
AOUTB1AOUTA2+
+1.8 V to +5 V
AOUTA2-
VLS
CS4365
0.1 µF
AOUTB2+
AOUTB2-
470 Ω
3
2
1
DSD
Audio
Source
48
47
46
42
19
15
MicroController
16
38
37
Analog Conditioning
and Muting
Analog Conditioning
and Muting
DSDA1
AOUTA3+
DSDB1
AOUTA3-
35
36
Analog Conditioning
and Muting
34
33
29
30
Analog Conditioning
and Muting
Analog Conditioning
and Muting
DSDA2
DSDB2
AOUTB3+
DSDA3
AOUTB3-
28
27
Analog Conditioning
and Muting
DSDB3
41
MUTEC1
MUTEC2 26
25
MUTEC3
24
MUTEC4
23
MUTEC5
MUTEC6 22
DSD_SCLK
RST
SCL/CCLK
Mute
Drive
SDA/CDIN
ADO/CS
2 KΩ
2 KΩ
17
40
SDIN3
470 Ω
43
39
Note*
18
+1.8 V to +5 V
FILT+ 20
VLC
CMOUT
0.1 µF
2
Note*: Necessary for I C
control port operation
+
21
0.1 µ F + 1 µF
GND
5
GND
31
0.1 µ F
47 µF
TST
10, 12,
14, 44, 45
Figure 6. Typical Connection Diagram, Software Mode
DS670F2
19
CS4365
+5 V
+2.5 V
1 µF
+
0.1 µF
0.1 µF
4
VD
220 Ω
6
7
PCM
Digital
Audio
Source
9
8
11
13
MCLK
AOUTA1+
LRCK
AOUTA1-
SCLK
MUTEC1
SDIN1
SDIN3
AOUTB1+
MUTEC2
VLS
AOUTA2+
AOUTA2-
3
2
1
DSD
Audio
Source
48
47
46
42
DSDA1
MUTEC3
AOUTB2+
DSDB2
AOUTB2-
DSDA3
DSD_SCLK
MUTEC4
AOUTA3+
+1.8 V to +5 V
MUTEC5
10
M4
12
M3
15
M2
16
17
19
18
38
37
26
Analog Conditioning
and Muting
35
36
25
Analog Conditioning
and Muting
34
33
24
Analog Conditioning
and Muting
DSDB3
AOUTA3-
Stand-Alone
Mode
Configuration
Analog Conditioning
and Muting
DSDB1
DSDA2
Optional
47 KΩ
40
41
CS4365
0.1 µF
470 Ω
39
SDIN2
AOUTB143
1 µF
32
VA
470 Ω
+1.8 V to +5 V
+
AOUTB3+
AOUTB3-
M1
MUTEC6
29
30
23
Analog Conditioning
and Muting
28
27
22
Analog Conditioning
and Muting
M0
RST
FILT+ 20
CMOUT
+
21
0.1 µ F + 1 µF
VLC
0.1 µ F
47 µF
0.1 µF
GND
5
GND
31
TST
14, 44, 45
Figure 7. Typical Connection Diagram, Hardware Mode
20
DS670F2
CS4365
4. APPLICATIONS
The CS4365 serially accepts two’s complement formatted PCM data at standard audio sample rates including 48,
44.1 and 32 kHz in SSM, 96, 88.2 and 64 kHz in DSM, and 192, 176.4 and 128 kHz in QSM. Audio data is input via
the serial data input pins (SDINx). The Left/Right Clock (LRCK) determines which channel is currently being input
on SDINx, and the Serial Clock (SCLK) clocks audio data into the input data buffer. For more information on serial
audio interfaces, see Cirrus Application Note AN282, “The 2-Channel Serial Audio Interface: A Tutorial.”
The CS4365 can be configured in Hardware Mode by the M0, M1, M2, M3 and M4 pins and in Software Mode
through I²C or SPI.
4.1
Master Clock
MCLK/LRCK must be an integer ratio as shown in Tables 1 - 3. The LRCK frequency is equal to Fs, the
frequency at which words for each channel are input to the device. The MCLK-to-LRCK frequency ratio and
speed mode is detected automatically during the initialization sequence by counting the number of MCLK
transitions during a single LRCK period and by detecting the absolute speed of MCLK. Internal dividers are
then set to generate the proper internal clocks. Tables 1 - 3 illustrate several standard audio sample rates
and the required MCLK and LRCK frequencies. Please note there is no required phase relationship, but
MCLK, LRCK and SCLK must be synchronous.
Sample Rate
(kHz)
256x
384x
MCLK (MHz)
512x
768x
32
44.1
48
8.1920
11.2896
12.2880
12.2880
16.9344
18.4320
16.3840
22.5792
24.5760
24.5760
33.8688
36.8640
1024x
1152x
32.7680
45.1584
49.1520
36.8640
= Denotes clock ratio and sample rate combinations which are NOT supported under auto speedmode detection. Please see “Switching Characteristics - PCM” on page 15.
Table 1. Single-Speed Mode Standard Frequencies
Sample Rate
(kHz)
128x
192x
64
88.2
96
8.1920
11.2896
12.2880
12.2880
16.9344
18.4320
MCLK (MHz)
256x
16.3840
22.5792
24.5760
384x
512x
24.5760
33.8688
36.8640
32.7680
45.1584
49.1520
= Denotes clock ratio and sample rate combinations which are NOT supported under auto speedmode detection. Please see “Switching Characteristics - PCM” on page 15.
Table 2. Double-Speed Mode Standard Frequencies
Sample Rate
(kHz)
64x
176.4
192
11.2896
12.2880
96x
MCLK (MHz)
128x
192x
256x
16.9344
18.4320
22.5792
24.5760
33.8688
36.8640
45.1584
49.1520
= Denotes clock ratio and sample rate combinations which are NOT supported under auto speedmode detection. Please see “Switching Characteristics - PCM” on page 15.
Table 3. Quad-Speed Mode Standard Frequencies
DS670F2
21
CS4365
4.2
Mode Select
In Hardware Mode, operation is determined by the Mode Select pins. The states of these pins are continually scanned for any changes; however, the mode should only be changed while the device is in reset
(RST pin low) to ensure proper switching from one mode to another. These pins require connection to supply or ground as outlined in Figure 7. For M0, M1, and M2, supply is VLC. For M3 and M4, supply is VLS.
Tables 4 - 6 show the decode of these pins.
In Software Mode, the operational mode and data format are set in the FM and DIF registers. See “PCM
Control (address 03h)” on page 35.
M1
(DIF1)
M0
(DIF0)
0
0
1
1
0
1
0
1
M4
M3
M2
(DEM)
0
0
0
0
1
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
X
DESCRIPTION
FORMAT
Left-Justified, up to 24-bit data
I²S, up to 24-bit data
Right-Justified, 16-bit Data
Right-Justified, 24-bit Data
Table 4. PCM Digital Interface Format, Hardware Mode Options
0
1
2
3
FIGURE
8
9
10
11
DESCRIPTION
Single-Speed without De-Emphasis (4 to 50 kHz sample rates)
Single-Speed with 44.1 kHz De-Emphasis; see Figure 16
Double-Speed (50 to 100 kHz sample rates)
Quad-Speed (100 to 200 kHz sample rates)
Auto Speed-Mode Detect (32 kHz to 200 kHz sample rates)
Auto Speed-Mode Detect with 44.1 kHz De-Emphasis; see Figure 16
DSD Processor Mode (see Table 6 for details)
Table 5. Mode Selection, Hardware Mode Options
M2
M1
M0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
DESCRIPTION
64x oversampled DSD data with a 4x MCLK to DSD data rate
64x oversampled DSD data with a 6x MCLK to DSD data rate
64x oversampled DSD data with a 8x MCLK to DSD data rate
64x oversampled DSD data with a 12x MCLK to DSD data rate
128x oversampled DSD data with a 2x MCLK to DSD data rate
128x oversampled DSD data with a 3x MCLK to DSD data rate
128x oversampled DSD data with a 4x MCLK to DSD data rate
128x oversampled DSD data with a 6x MCLK to DSD data rate
Table 6. Direct Stream Digital (DSD), Hardware Mode Options
22
DS670F2
CS4365
4.3
Digital Interface Formats
The serial port operates as a slave and supports the I²S, Left-Justified, Right-Justified, and One-Line Mode
(OLM) digital interface formats with varying bit depths from 16 to 32, as shown in Figures 8-15. Data is
clocked into the DAC on the rising edge. OLM configuration is only supported in Software Mode.
Left Channel
LRCK
Right Channel
SCLK
SDINx
MSB
-1 -2 -3 -4 -5
+5 +4 +3 +2 +1
LSB
MSB
-1 -2 -3 -4
+5 +4 +3 +2 +1
LSB
Figure 8. Format 0 - Left-Justified up to 24-bit Data
Left Channel
LRCK
Right Channel
SCLK
SDINx
MSB
-1 -2 -3 -4 -5
+5 +4 +3 +2 +1
LSB
MSB
-1 -2 -3 -4
+5 +4 +3 +2 +1 LSB
Figure 9. Format 1 - I²S up to 24-bit Data
LRCK
Right Channel
Left Channel
SCLK
SDINx
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
32 clocks
Figure 10. Format 2 - Right-Justified 16-bit Data
LRCK
Right Channel
Left Channel
SCLK
SDINx
0
23 22 21 20 19 18
7 6 5 4 3 2 1 0
23 22 21 20 19 18
7 6 5 4 3 2 1 0
32 clocks
Figure 11. Format 3 - Right-Justified 24-bit Data
LRCK
Right Channel
Left Channel
SCLK
SDINx
1 0
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
32 clocks
Figure 12. Format 4 - Right-Justified 20-bit Data
DS670F2
23
CS4365
LRCK
Right Channel
Left Channel
SCLK
SDINx
1 0
17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
32 clocks
Figure 13. Format 5 - Right-Justified 18-bit Data
4.3.1
OLM #1
OLM #1 serial audio interface format operates in Single-, Double-, or Quad-Speed Mode and will slave to
SCLK at 128 Fs. Six channels of MSB first 20-bit PCM data are input on SDIN1.
LRCK
64 clks
64 clks
Left Channel
Right Channel
SCLK
MSB
SDIN1
LSB MSB
DAC_A1
20 clks
LSB MSB
LSB
MSB
LSB MSB
LSB MSB
LSB
DAC_A2
DAC_A3
DAC_B1
DAC_B2
DAC_B3
20 clks
20 clks
20 clks
20 clks
20 clks
MSB
Figure 14. Format 8 - One-Line Mode 1
4.3.2
OLM #2
OLM #2 serial audio interface format operates in Single-, Double-, or Quad-Speed Mode and will slave to
SCLK at 256 Fs. Six channels of MSB first 24-bit PCM data are input on SDIN1.
LRCK
128 clks
128 clks
Left C hannel
Right C hannel
SC LK
SD IN1
M SB
LS B M SB
LS B M S B
LS B
M SB
LS B M SB
LS B M SB
LS B
DAC _A1
DAC_A2
DAC_A3
DAC_B1
DAC_B2
DAC_B3
24 clks
24 clks
24 clks
24 clks
24 clks
24 clks
MSB
Figure 15. Format 9 - One-Line Mode 2
4.4
Oversampling Modes
The CS4365 operates in one of three oversampling modes based on the input sample rate. Mode selection
is determined by the M4, M3 and M2 pins in Hardware Mode or the FM bits in Software Mode. Single-Speed
mode supports input sample rates up to 50 kHz and uses a 128x oversampling ratio. Double-Speed Mode
supports input sample rates up to 100 kHz and uses an oversampling ratio of 64x. Quad-Speed Mode supports input sample rates up to 200 kHz and uses an oversampling ratio of 32x.
The auto-speed mode detect feature allows for the automatic selection of speed mode based off of the incoming sample rate. This allows the CS4365 to accept a wide range of sample rates with no external intervention necessary. The auto-speed mode detect feature is available in both hardware and Software Mode.
24
DS670F2
CS4365
4.5
Interpolation Filter
To accommodate the increasingly complex requirements of digital audio systems, the CS4365 incorporates
selectable interpolation filters for each mode of operation. A “fast” and a “slow” roll-off filter is available in
each of Single, Double, and Quad-Speed modes. These filters have been designed to accommodate a variety of musical tastes and styles. The FILT_SEL bit is used to select which filter is used (see the “Filter
Plots” on page 45 for more details).
When in Hardware Mode, only the “fast” roll-off filter is available.
Filter specifications can be found in Section , and filter response plots can be found in Figures 24 to 47.
4.6
De-Emphasis
The CS4365 includes on-chip digital de-emphasis filters. The de-emphasis feature is included to accommodate older audio recordings that utilize pre-emphasis equalization as a means of noise reduction. Figure 16
shows the de-emphasis curve. The frequency response of the de-emphasis curve will scale proportionally
with changes in sample rate, Fs if the input sample rate does not match the coefficient which has been selected.
In Software Mode the required de-emphasis filter coefficients for 32 kHz, 44.1 kHz, or 48 kHz are selected
via the de-emphasis control bits.
In Hardware Mode only the 44.1 kHz coefficient is available (enabled through the M2 pin). If the input sample rate is not 44.1 kHz and de-emphasis has been selected then the corner frequencies of the de-emphasis
filter will be scaled by a factor of the actual Fs over 44,100.
Gain
dB
T1=50 µs
0dB
T2 = 15 µs
-10dB
F1
3.183 kHz
F2
Frequency
10.61 kHz
Figure 16. De-Emphasis Curve
DS670F2
25
CS4365
4.7
ATAPI Specification
The CS4365 implements the channel-mixing functions of the ATAPI CD-ROM specification. The
ATAPI functions are applied per A-B pair. Refer to Table 9 on page 42 and Figure 17 for additional information.
A Channel
Volume
Control
Left Channel
Audio Data
Σ
SDINx
Right Channel
Audio Data
MUTE
Aout Ax
MUTE
AoutBx
Σ
B Channel
Volume
Control
Figure 17. ATAPI Block Diagram (x = channel pair 1, 2, or 3)
4.8
Direct Stream Digital (DSD) Mode
In Software Mode, the DSD/PCM bits (Reg. 02h) are used to configure the device for DSD Mode. The
DSD_DIF bits (Reg 04h) then control the expected DSD rate and MCLK ratio.
The DIR_DSD bit (Reg 04h) selects between two proprietary methods for DSD-to-analog conversion. The
first method uses a decimation-free DSD processing technique which allows for features such as matched
PCM-level output, DSD volume control, and 50kHz on-chip filter. The second method sends the DSD data
directly to the on-chip switched-capacitor filter for conversion (without the above-mentioned features).
The DSD_PM_EN bit (Reg. 04h) selects Phase Modulation (data plus data inverted) as the style of data
input. In this mode, the DSD_PM_mode bit selects whether a 128Fs or 64x clock is used for phase modulated 64x data (see Figure 18). Use of Phase Modulation Mode may not directly affect the performance of
the CS4365, but may lower the sensitivity to board-level routing of the DSD data signals.
The CS4365 can detect errors in the DSD data which does not comply with the SACD specification. The
STATIC_DSD and INVALID_DSD bits (Reg. 04h) allow the CS4365 to alter the incoming invalid DSD data.
Depending on the error, the data may either be attenuated or replaced with a muted DSD signal (the
MUTEC pins would be set according to the DAMUTE bit (Reg. 08h)).
More information for any of these register bits can be found in Section 7. “Filter Plots” on page 45.
The DSD input structure and analog outputs are designed to handle a nominal 0 dB-SACD (50% modulation
index) at full rated performance. Signals of +3 dB-SACD may be applied for brief periods of time, however;
performance at these levels is not guaranteed. If sustained +3 dB-SACD levels are required, the digital volume control should be set to -3.0 dB. This same volume control register affects PCM output levels. There
is no need to change the volume control setting between PCM and DSD in order to have the 0dB output
levels match (both 0 dBFS and 0 dB-SACD will output at -3 dB in this case).
26
DS670F2
CS4365
DSD Phase
Modulation Mode
DSD Normal Mode
BCKA
(64Fs)
Not Used
DSD_SCLK
BCKA
(128Fs)
DSD_SCLK
DSD_SCLK
BCKD
(64Fs)
Not Used
DSDAx,
DSDBx
D0
D0
D1
D1
D1
D2
D2
DSDAx,
DSDBx
Not Used
Figure 18. DSD Phase Modulation Mode Diagram
4.9
Grounding and Power Supply Arrangements
As with any high-resolution converter, the CS4365 requires careful attention to power supply and grounding
arrangements if its potential performance is to be realized. The Typical Connection Diagram shows the recommended power arrangements, with VA, VD, VLC, and VLS connected to clean supplies. If the ground
planes are split between digital ground and analog ground, the GND pins of the CS4365 should be connected to the analog ground plane.
All signals, especially clocks, should be kept away from the FILT+ and VQ pins in order to avoid unwanted
coupling into the DAC.
4.9.1
Capacitor Placement
Decoupling capacitors should be placed as close to the DAC as possible, with the low value ceramic capacitor being the closest. To further minimize impedance, these capacitors should be located on the same
layer as the DAC. If desired, all supply pins with similar voltage ratings may be connected to the same
supply, but a decoupling capacitor should still be placed on each supply pin.
Notes:
All decoupling capacitors should be referenced to ground.
The CDB4365 evaluation board demonstrates the optimum layout and power supply arrangements.
DS670F2
27
CS4365
4.10
Analog Output and Filtering
The application note “Design Notes for a 2-Pole Filter with Differential Input” discusses the second-order
Butterworth filter and differential to single-ended converter which was implemented on the CS4365 evaluation board, CDB4365, as seen in Figure 20. The CS4365 does not include phase or amplitude compensation for an external filter. Therefore, the DAC system phase and amplitude response will be dependent on
the external analog circuitry. The off-chip filter has been designed to attenuate the typical full-scale output
level to below 2 Vrms.
Figure 19 shows how the full-scale differential analog output level specification is derived.
4.15 V
2.5 V
AOUT+
0.85 V
4.15 V
AOUT-
2.5 V
0.85 V
Full-Scale Output Level= (AOUT+) - (AOUT-)= 6.6 Vpp
Figure 19. Full-Scale Output
Figure 20. Recommended Output Filter
28
DS670F2
CS4365
4.11
The MUTEC Outputs
The MUTEC1-6 pins have an auto-polarity detect feature. The MUTEC output pins are high impedance at
the time of reset. The external mute circuitry needs to be self-biased into an active state in order to be muted
during reset. Upon release of reset, the CS4365 will detect the status of the MUTEC pins (high or low) and
will then select that state as the polarity to drive when the mutes become active. The external-bias voltage
level that the MUTEC pins see at the time of release of reset must meet the “MUTEC auto-detect input
high/low voltage” specifications as outlined in the Digital Characteristics section.
Figure 21 shows a single example of both an active high and an active low mute drive circuit. In these designs, the pull-up and pull-down resistors have been especially chosen to meet the input high/low threshold
when used with the MMUN2111 and MMUN2211 internal bias resistances of 10 kΩ. Use of the Mute Control
function is not mandatory, but recommended, for designs requiring the absolute minimum in extraneous
clicks and pops. Also, use of the Mute Control function can enable the system designer to achieve idle channel noise/signal-to-noise ratios which are only limited by the external mute circuit.
Figure 21. Recommended Mute Circuitry
4.12
Recommended Power-Up Sequence
4.12.1 Hardware Mode
1. Hold RST low until the power supplies and configuration pins are stable, and the master and left/right
clocks are locked to the appropriate frequencies, as discussed in Section 4.1. In this state, the
registers are reset to the default settings, FILT+ will remain low, and VQ will be connected to VA/2.
If RST can not be held low long enough the SDINx pins should remain static low until all other clocks
are stable, and if possible the RST should be toggled low again once the system is stable.
2. Bring RST high. The device will remain in a low power state with FILT+ low and will initiate the
Hardware power-up sequence after approximately 512 LRCK cycles in Single-Speed Mode (1024
LRCK cycles in Double-Speed Mode, and 2048 LRCK cycles in Quad-Speed Mode).
DS670F2
29
CS4365
4.12.2 Software Mode
1. Hold RST low until the power supply is stable, and the master and left/right clocks are locked to the
appropriate frequencies, as discussed in Section 4.1. In this state, the registers are reset to the default
settings, FILT+ will remain low, and VQ will be connected to VA/2.
2. Bring RST high. The device will remain in a low power state with FILT+ low for 512 LRCK cycles in
Single-Speed Mode (1024 LRCK cycles in Double-Speed Mode, and 2048 LRCK cycles in QuadSpeed Mode).
3. In order to reduce the chances of clicks and pops, perform a write to the CP_EN bit prior to the
completion of approximately 512 LRCK cycles in Single-Speed Mode (1024 LRCK cycles in DoubleSpeed Mode, and 2048 LRCK cycles in Quad-Speed Mode). The desired register settings can be
loaded while keeping the PDN bit set to 1. Set the RMP_UP and RMP_DN bits to 1; then set the
format and mode control bits to the desired settings.
If more than the stated range of LRCK cycles passes before CPEN bit is written, the chip will enter
Hardware Mode and begin to operate with the M0-M4 as the mode settings. CPEN bit may be written
at anytime, even after the Hardware sequence has begun. It is advised that if the CPEN bit cannot be
set in time, the SDINx pins should remain static low (this way no audio data can be converted
incorrectly by the Hardware Mode settings).
4. Set the PDN bit to 0. This will initiate the power-up sequence, which lasts approximately 50 µs.
4.13
Recommended Procedure for Switching Operational Modes
For systems where the absolute minimum in clicks and pops is required, it is recommended that the MUTE
bits are set prior to changing significant DAC functions (such as changing sample rates or clock sources).
The mute bits may then be released after clocks have settled and the proper modes have been set.
It is required to have the device held in reset if the minimum high/low time specs of MCLK cannot be met
during clock source changes.
4.14
Control Port Interface
The control port is used to load all the internal register settings in order to operate in Software Mode (see
Section 7. “Filter Plots” on page 45). The operation of the control port may be completely asynchronous with
the audio sample rate. However, to avoid potential interference problems, the control port pins should remain static if no operation is required.
The control port operates in one of two modes: I²C or SPI.
4.14.1 MAP Auto Increment
The device has MAP (memory address pointer) auto-increment capability enabled by the INCR bit (also
the MSB) of the MAP. If INCR is set to 0, MAP will stay constant for successive I²C writes or reads and
SPI writes. If INCR is set to 1, MAP will auto-increment after each byte is written, allowing block reads or
writes of successive registers.
4.14.2 I²C Mode
In the I²C Mode, data is clocked into and out of the bi-directional serial control data line, SDA, by the serial
control port clock, SCL (see Figure 22 for the clock to data relationship). There is no CS pin. The AD0 pin
enables the user to alter the chip address (001100[AD0][R/W]) and should be tied to VLC or GND, as required, before powering up the device. If the device ever detects a high-to-low transition on the AD0/CS
pin after power-up, SPI Mode will be selected.
30
DS670F2
CS4365
4.14.2.1 I²C Write
To write to the device, follow the procedure below while adhering to the control port Switching Specifications in Section .
1. Initiate a START condition to the I²C bus followed by the address byte. The upper 6 bits must be
001100. The seventh bit must match the setting of the AD0 pin, and the eighth must be 0. The eighth
bit of the address byte is the R/W bit.
2. Wait for an acknowledge (ACK) from the part, then write to the memory address pointer, MAP. This
byte points to the register to be written.
3. Wait for an acknowledge (ACK) from the part, then write the desired data to the register pointed to by
the MAP.
4. If the INCR bit (see Section 4.14.1) is set to 1, repeat the previous step until all the desired registers
are written, then initiate a STOP condition to the bus.
5. If the INCR bit is set to 0 and further I²C writes to other registers are desired, it is necessary to initiate
a repeated START condition and follow the procedure detailed from step 1. If no further writes to other
registers are desired, initiate a STOP condition to the bus.
4.14.2.2 I²C Read
To read from the device, follow the procedure below while adhering to the control port Switching Specifications.
1. Initiate a START condition to the I²C bus followed by the address byte. The upper 6 bits must be
001100. The seventh bit must match the setting of the AD0 pin, and the eighth must be 1. The eighth
bit of the address byte is the R/W bit.
2. After transmitting an acknowledge (ACK), the device will then transmit the contents of the register
pointed to by the MAP. The MAP register will contain the address of the last register written to the
MAP, or the default address (see Section 4.14.1) if an I²C read is the first operation performed on the
device.
3. Once the device has transmitted the contents of the register pointed to by the MAP, issue an ACK.
4. If the INCR bit is set to 1, the device will continue to transmit the contents of successive registers. Continue providing a clock and issue an ACK after each byte until all the desired registers are read, then
initiate a STOP condition to the bus.
5. If the INCR bit is set to 0 and further I²C reads from other registers are desired, it is necessary to initiate
a repeated START condition and follow the procedure detailed from steps 1 and 2 from the I²C Write
instructions followed by step 1 of the I²C Read section. If no further reads from other registers are desired, initiate a STOP condition to the bus.
N ote 1
SDA
001100
ADDR
AD 0
R/W
ACK
DATA
1-8
ACK
DATA
1-8
ACK
SCL
Start
Stop
N ote: If operation is a w rite, th is byte contain s the M em o ry A ddress P ointer, M A P.
Figure 22. Control Port Timing, I²C Mode
DS670F2
31
CS4365
4.14.3 SPI Mode
In SPI Mode, data is clocked into the serial control data line, CDIN, by the serial control port clock, CCLK
(see Figure 23 for the clock to data relationship). There is no AD0 pin. Pin CS is the chip select signal and
is used to control SPI writes to the control port. When the device detects a high to low transition on the
AD0/CS pin after power-up, SPI Mode will be selected. All signals are inputs and data is clocked in on the
rising edge of CCLK.
4.14.3.1 SPI Write
To write to the device, follow the procedure below while adhering to the control port Switching Specifications in Section .
1. Bring CS low.
2. The address byte on the CDIN pin must then be 00110000.
3. Write to the memory address pointer, MAP. This byte points to the register to be written.
4. Write the desired data to the register pointed to by the MAP.
5. If the INCR bit (see Section 4.14.1) is set to 1, repeat the previous step until all the desired registers
are written, then bring CS high.
6. If the INCR bit is set to 0 and further SPI writes to other registers are desired, it is necessary to bring
CS high, and follow the procedure detailed from step 1. If no further writes to other registers are desired, bring CS high.
CS
CCLK
CHIP
ADDRESS
C DIN
0011000
MAP
DATA
LSB
MSB
R/W
byte 1
byte n
M AP = M em ory Address Pointer
Figure 23. Control Port Timing, SPI Mode
4.15
Memory Address Pointer (MAP)
7
INCR
0
6
Reserved
0
5
Reserved
0
4
MAP4
0
3
MAP3
0
2
MAP2
0
1
MAP1
0
0
MAP0
0
4.15.1 INCR (Auto Map Increment Enable)
Default = ‘0’
0 - Disabled
1 - Enabled
4.15.2 MAP4-0 (Memory Address Pointer)
Default = ‘00000’
32
DS670F2
CS4365
5. REGISTER QUICK REFERENCE
Addr
Function
01h
Chip Revision
02h
Mode Control
default
default
03h
PCM Control
default
04h
DSD Control
05h
Filter Control
06h
Invert Control
07h
Group Control
08h
Ramp and Mute
09h
Mute Control
default
default
default
default
default
default
0Ah Mixing Control
Pair 1 (AOUTx1)
default
0Bh Vol. Control A1
default
0Ch Vol. Control B1
default
0Dh Mixing Control
Pair 2 (AOUTx1)
default
0Eh Vol. Control A2
default
0Fh
Vol. Control B2
default
10h
Mixing Control
Pair 3 (AOUTx1)
11h
Vol. Control A3
12h
Vol. Control B3
default
default
default
16h
7
6
5
4
3
2
1
0
PART4
PART3
PART2
PART1
PART0
REV
REV
REV
0
1
x
x
0
1
1
CPEN
FREEZE
DSD/PCM
0
0
0
0
0
0
0
1
DIF3
DIF2
DIF1
DIF0
Reserved
Reserved
FM1
FM0
0
0
0
0
0
0
1
1
DSD_DIF2 DSD_DIF1 DSD_DIF0 DIR_DSD
DS670F2
x
PDN
STATIC_D INVALID_D DSD_PM_ DSD_PM_
SD
SD
MD
EN
0
0
0
0
1
0
0
0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
FILT_SEL
0
0
0
0
0
0
0
0
Reserved
Reserved
INV_B3
INV_A3
INV_B2
INV_A2
INV_B1
INV_A1
0
0
0
0
0
0
0
0
MUTEC1
MUTEC0
Reserved
P1_A=B
P2_A=B
P3_A=B
Reserved
SNGLVOL
0
0
0
0
0
0
0
0
SZC1
SZC0
RMP_UP
RMP_DN
PAMUTE
DAMUTE
MUTE_P1
MUTE_P0
1
1
1
1
0
Reserved
Reserved
MUTE_B3 MUTE_A3 MUTE_B2
1
0
0
MUTE_A2
MUTE_B1
MUTE_A1
0
0
0
0
0
0
0
0
Reserved
P1_DEM1
P1_DEM0
P1ATAPI4
P1ATAPI3
P1ATAPI2
P1ATAPI1
P1ATAPI0
0
0
0
0
1
0
0
1
A1_VOL7
A1_VOL6
A1_VOL5
A1_VOL4
A1_VOL3
A1_VOL2
A1_VOL1
A1_VOL0
0
0
0
0
0
0
0
0
B1_VOL7
B1_VOL6
B1_VOL5
B1_VOL4
B1_VOL3
B1_VOL2
B1_VOL1
B1_VOL0
0
0
0
0
0
0
0
0
Reserved
P2_DEM1
P2_DEM0
P2ATAPI4
P2ATAPI3
P2ATAPI2
P2ATAPI1
P2ATAPI0
0
0
0
0
1
0
0
1
A2_VOL7
A2_VOL6
A2_VOL5
A2_VOL4
A2_VOL3
A2_VOL2
A2_VOL1
A2_VOL0
0
0
0
0
0
0
0
0
B2_VOL7
B2_VOL6
B2_VOL5
B2_VOL4
B2_VOL3
B2_VOL2
B2_VOL1
B2_VOL0
0
0
0
0
0
0
0
0
Reserved
P3_DEM1
P3_DEM0
P3ATAPI4
P3ATAPI3
P3ATAPI2
P3ATAPI1
P3ATAPI0
0
0
0
0
1
0
0
1
A3_VOL7
A3_VOL6
A3_VOL5
A3_VOL4
A3_VOL3
A3_VOL2
A3_VOL1
A3_VOL0
0
0
0
0
0
0
0
0
B3_VOL7
B3_VOL6
B3_VOL5
B3_VOL4
B3_VOL3
B3_VOL2
B3_VOL1
B3_VOL0
0
0
0
0
0
0
0
0
Reserved
MCLKDIV
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
0
0
0
0
0
PCM clock mode Reserved
default
Reserved DAC3_DIS DAC2_DIS DAC1_DIS
0
33
CS4365
6.
REGISTER DESCRIPTION
Note:
All registers are read/write in I²C Mode and write only in SPI, unless otherwise noted.
6.1
Chip Revision (address 01h)
7
6
5
4
3
2
1
0
PART4
0
PART3
1
PART2
1
PART1
0
PART0
1
REV2
-
REV1
-
REV0
-
6.1.1 Part Number ID (PART) [Read Only]
01101- CS4365
Revision ID (REV) [Read Only]
000 - Revision A0
001 - Revision B0
Function:
This read-only register can be used to identify the model and revision number of the device.
6.2
Mode Control 1 (address 02h)
7
6
5
4
3
2
1
0
CPEN
0
FREEZE
0
DSD/PCM
0
Reserved
0
DAC3_DIS
0
DAC2_DIS
0
DAC1_DIS
0
PDN
1
6.2.1 Control Port Enable (CPEN)
Default = 0
0 - Disabled
1 - Enabled
Function:
This bit defaults to 0, allowing the device to power-up in Stand-Alone Mode. The Control Port Mode can
be accessed by setting this bit to 1. This will allow the operation of the device to be controlled by the registers, and the pin definitions will conform to Control Port Mode. To accomplish a clean power-up, the user
should write this bit within 10 ms following the release of Reset.
6.2.2 Freeze Controls (FREEZE)
Default = 0
0 - Disabled
1 - Enabled
Function:
This function allows modifications to be made to the registers without the changes taking effect until the
FREEZE is disabled. To make multiple changes in the Control port registers take effect simultaneously,
enable the FREEZE Bit, make all register changes, then Disable the FREEZE bit.
34
DS670F2
CS4365
6.2.3 PCM/DSD Selection (DSD/PCM)
Default = 0
0 - PCM
1 - DSD
Function:
This function selects DSD or PCM Mode. The appropriate data and clocks should be present before
changing modes, or else MUTE should be selected.
6.2.4 DAC Pair Disable (DACx_DIS)
Default = 0
0 - DAC Pair x Enabled
1 - DAC Pair x Disabled
Function:
When the bit is set, the respective DAC channel pair (AOUTAx and AOUTBx) will remain in a reset state.
It is advised that changes to these bits be made while the power-down (PDN) bit is enabled to eliminate
the possibility of audible artifacts.
6.2.5 Power Down (PDN)
Default = 1
0 - Disabled
1 - Enabled
Function:
The entire device will enter a low-power state when this function is enabled, and the contents of the control
registers are retained in this mode. The power-down bit defaults to ‘enabled’ on power-up and must be
disabled before normal operation in Control Port Mode can occur.
6.3
PCM Control (address 03h)
7
6
5
4
3
2
1
0
DIF3
0
DIF2
0
DIF1
0
DIF0
0
Reserved
0
Reserved
0
FM1
1
FM0
1
6.3.1 Digital Interface Format (DIF)
Default = 0000 - Format 0 (Left-Justified, up to 24-bit data)
Function:
These bits select the interface format for the serial audio input. The DSD/PCM bit determines whether
PCM or DSD Mode is selected.
The required relationship between the Left/Right clock, serial clock and serial data is defined by the Digital
Interface Format and the options are detailed in Figures 8 through 15.
Note: While in PCM Mode, the DIF bits should only be changed when the power-down (PDN) bit is set
to ensure proper switching from one mode to another.
DS670F2
35
CS4365
DIF3
DIF2
DIF1
DIF0
0
0
0
0
0
0
1
1
X
0
0
0
0
1
1
0
0
X
0
0
1
1
0
0
0
0
X
0
1
0
1
0
1
0
1
X
DESCRIPTION
FORMAT
Left-Justified, up to 24-bit data
I²S, up to 24-bit data
Right-Justified, 16-bit data
Right-Justified, 24-bit data
Right-Justified, 20-bit data
Right-Justified, 18-bit data
One-Line Mode 1, 24-bit Data
One-Line Mode 2, 20-bit Data
All other combinations are Reserved
0
1
2
3
4
5
8
9
Table 7. Digital Interface Formats - PCM Mode
6.3.2 Functional Mode (FM)
Default = 11
00 - Single-Speed Mode (4 to 50 kHz sample rates)
01 - Double-Speed Mode (50 to 100 kHz sample rates)
10 - Quad-Speed Mode (100 to 200 kHz sample rates)
11 - Auto Speed Mode detect (32 kHz to 200 kHz sample rates)
Function:
Selects the required range of input sample rates or Auto Speed Mode.
6.4
DSD Control (address 04h)
7
6
5
4
DSD_DIF2
0
DSD_DIF1
0
DSD_DIF0
0
DIR_DSD
0
3
2
1
0
STATIC_DSD INVALID_DSD DSD_PM_MD DSD_PM_EN
1
1
0
0
6.4.1 DSD Mode Digital Interface Format (DSD_DIF)
Default = 000 - Format 0 (64x oversampled DSD data with a 4x MCLK to DSD data rate)
Function:
The relationship between the oversampling ratio of the DSD audio data and the required Master clock-toDSD-data rate is defined by the Digital Interface Format pins.
The DSD/PCM bit determines whether PCM or DSD Mode is selected.
DIF2
DIF1
DIFO
DESCRIPTION
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
64x oversampled DSD data with a 4x MCLK to DSD data rate
64x oversampled DSD data with a 6x MCLK to DSD data rate
64x oversampled DSD data with a 8x MCLK to DSD data rate
64x oversampled DSD data with a 12x MCLK to DSD data rate
128x oversampled DSD data with a 2x MCLK to DSD data rate
128x oversampled DSD data with a 3x MCLK to DSD data rate
128x oversampled DSD data with a 4x MCLK to DSD data rate
128x oversampled DSD data with a 6x MCLK to DSD data rate
Table 8. Digital Interface Formats - DSD Mode
36
DS670F2
CS4365
6.4.2 Direct DSD Conversion (DIR_DSD)
Function:
When set to 0 (default), DSD input data is sent to the DSD processor for filtering and volume control functions.
When set to 1, DSD input data is sent directly to the switched capacitor DACs for a pure DSD conversion.
In this mode, the full-scale DSD and PCM levels will not be matched (see Section ), the dynamic range
performance may be reduced, the volume control is inactive, and the 50 kHz low pass filter is not available
(see Section for filter specifications).
6.4.3 Static DSD Detect (STATIC_DSD)
Function:
When set to 1 (default), the DSD processor checks for 28 consecutive zeroes or ones and, if detected,
sends a mute signal to the DACs. The MUTEC pins will eventually go active according to the DAMUTE
register.
When set to 0, this function is disabled.
6.4.4 Invalid DSD Detect (INVALID_DSD)
Function:
When set to 1, the DSD processor checks for greater than 24 out of 28 bits of the same value and, if detected, will attenuate the data sent to the DACs. The MUTEC pins go active according to the DAMUTE
register.
When set to 0 (default), this function is disabled.
6.4.5 DSD Phase Modulation Mode Select (DSD_PM_MODE)
Function:
When set to 0 (default), the 128Fs (BCKA) clock should be input to DSD_SCLK for Phase Modulation
Mode. (See Figure 18 on page 27)
When set to 1, the 64Fs (BCKD) clock should be input to DSD_SCLK for Phase Modulation Mode.
6.4.6 DSD Phase Modulation Mode Enable (DSD_PM_EN)
Function:
When set to 1, DSD phase modulation input mode is enabled, and the DSD_PM_MODE bit should be set
accordingly.
When set to 0 (default), this function is disabled (DSD normal mode).
DS670F2
37
CS4365
6.5
Filter Control (address 05h)
7
6
5
4
3
2
1
0
Reserved
0
Reserved
0
Reserved
0
Reserved
0
Reserved
0
Reserved
0
Reserved
0
FILT_SEL
0
6.5.1 Interpolation Filter Select (FILT_SEL)
Function:
When set to 0 (default), the Interpolation Filter has a fast roll-off.
When set to 1, the Interpolation Filter has a slow roll-off.
The specifications for each filter can be found in the Analog characteristics table, and response plots can
be found in Figures 24 to 47.
6.6
Invert Control (address 06h)
7
6
5
4
3
2
1
0
Reserved
0
Reserved
0
INV_B3
0
INV_A3
0
INV_B2
0
INV_A2
0
INV_B1
0
INV_A1
0
6.6.1 Invert Signal Polarity (Inv_xx)
Function:
When set to 1, this bit inverts the signal polarity of channel xx.
When set to 0 (default), this function is disabled.
6.7
Group Control (address 07h)
7
6
5
4
3
2
1
0
MUTEC1
0
MUTEC0
0
Reserved
0
P1_A=B
0
P2_A=B
0
P3_A=B
0
Reserved
0
SNGLVOL
0
6.7.1 Mute Pin Control (MUTEC1, MUTEC0)
Default = 00
00 - Six mute control signals
01, 10 - One mute control signal
11 - Three mute control signals
Function:
Selects how the internal mute control signals are routed to the MUTEC1 through MUTEC6 pins. When
set to ‘00’, there is one mute control signal for each channel: AOUT1A on MUTEC1, AOUT1B on
MUTEC2, etc. When set to ‘01’ or ‘10’, there is a single mute control signal on the MUTEC1 pin. When
set to ‘11’, there are three mute control signals, one for each stereo pair: AOUT1A and AOUT1B on
MUTEC1, AOUT2A and AOUT2B on MUTEC2, and AOUT3A and AOUT3B on MUTEC3.
38
DS670F2
CS4365
6.7.2 Channel A Volume = Channel B Volume (Px_A=B)
Default = 0
0 - Disabled
1 - Enabled
Function:
The AOUTAx and AOUTBx volume levels are independently controlled by the A and the B Channel Volume Control Bytes when this function is disabled. The volume on both AOUTAx and AOUTBx are determined by the A Channel Attenuation and Volume Control Bytes (per A-B pair), and the B Channel Bytes
are ignored when this function is enabled.
6.7.3 Single Volume Control (SNGLVOL)
Default = 0
0 - Disabled
1 - Enabled
Function:
The individual channel volume levels are independently controlled by their respective Volume Control
Bytes when this function is disabled. The volume on all channels is determined by the A1 Channel Volume
Control Byte, and the other Volume Control Bytes are ignored when this function is enabled.
6.8
Ramp and Mute (address 08h)
7
6
5
4
3
2
1
0
SZC1
1
SZC0
0
RMP_UP
1
RMP_DN
1
PAMUTE
1
DAMUTE
1
MUTE_P1
0
MUTE_P0
0
6.8.1 Soft Ramp and Zero Cross CONTROL (SZC)
Default = 10
00 - Immediate Change
01 - Zero Cross
10 - Soft Ramp
11 - Soft Ramp on Zero Crossings
Function:
Immediate Change
When Immediate Change is selected, all level changes will take effect immediately in one step.
Zero Cross
Zero Cross Enable dictates that signal-level changes, either by attenuation changes or muting, will occur
on a signal zero crossing to minimize audible artifacts. The requested level change will occur after a timeout period between 512 and 1024 sample periods (10.7 ms to 21.3 ms at 48 kHz sample rate) if the signal
does not encounter a zero crossing. The zero cross function is independently monitored and implemented
for each channel.
Soft Ramp
Soft Ramp allows level changes, both muting and attenuation, to be implemented by incrementally ramping, in 1/8 dB steps, from the current level to the new level at a rate of 1 dB per 8 left/right clock periods.
DS670F2
39
CS4365
Soft Ramp on Zero Crossing
Soft Ramp and Zero Cross Enable dictates that signal-level changes, either by attenuation changes or
muting, will occur in 1/8 dB steps and be implemented on a signal zero crossing. The 1/8 dB level change
will occur after a timeout period between 512 and 1024 sample periods (10.7 ms to 21.3 ms at 48 kHz
sample rate) if the signal does not encounter a zero crossing. The zero cross function is independently
monitored and implemented for each channel.
6.8.2 Soft Volume Ramp-Up after Error (RMP_UP)
Function:
An un-mute will be performed after executing an LRCK/MCLK ratio change or error, and after changing
the Functional Mode.
When set to 1 (default), this unmute is effected, similar to attenuation changes, by the Soft and Zero Cross
bits in the Volume and Mixing Control register.
When set to 0, an immediate unmute is performed in these instances.
Note:
For best results, it is recommended that this feature be used in conjunction with the RMP_DN bit.
6.8.3 Soft Ramp-Down before Filter Mode Change (RMP_DN)
Function:
If either the FILT_SEL or DEM bits are changed the DAC will stop conversion for a period of time to
change its filter values. This bit selects how the data is effected prior to and after the change of the filter
values.
When set to 1 (default), a mute will be performed prior to executing a filter mode change and an un-mute
will be performed after executing the filter mode change. This mute and un-mute are effected, similar to
attenuation changes, by the Soft and Zero Cross bits in the Volume and Mixing Control register.
When set to 0, an immediate mute is performed prior to executing a filter mode change.
Note:
For best results, it is recommended that this feature be used in conjunction with the RMP_UP bit.
6.8.4 PCM Auto-Mute (PAMUTE)
Function:
When set to 1 (default), the Digital-to-Analog converter output will mute following the reception of 8192
consecutive audio samples of static 0 or -1. A single sample of non-static data will release the mute. Detection and muting is done independently for each channel. The quiescent voltage on the output will be
retained and the Mute Control pin will go active during the mute period.
When set to 0, this function is disabled.
40
DS670F2
CS4365
6.8.5 DSD Auto-Mute (DAMUTE)
Function:
When set to 1 (default), the Digital-to-Analog converter output will mute following the reception of 256 repeated 8-bit DSD mute patterns (as defined in the SACD specification).
A single bit not fitting the repeated mute pattern (mentioned above) will release the mute. Detection and
muting is done independently for each channel. The quiescent voltage on the output will be retained, and
the Mute Control pin will go active during the mute period.
6.8.6 MUTE Polarity and DETECT (MUTEP1:0)
Default = 00
00 - Auto polarity detect, selected from MUTEC1 pin
01 - Reserved
10 - Active low mute polarity
11 - Active high mute polarity
Function:
Auto mute polarity detect (00)
See Section 4.11 “The MUTEC Outputs” on page 29 for description.
Active low mute polarity (10)
When RST is low, the outputs are high impedance and will need to be biased active. Once reset has been
released and after this bit is set, the MUTEC output pins will be active low polarity.
Active high mute polarity (11)
At reset time, the outputs are high impedance and will need to be biased active. Once reset has been
released and after this bit is set, the MUTEC output pins will be active high polarity.
6.9
Mute Control (address 09h)
7
6
5
4
3
2
1
0
Reserved
0
Reserved
0
MUTE_B3
0
MUTE_A3
0
MUTE_B2
0
MUTE_A2
0
MUTE_B1
0
MUTE_A1
0
6.9.1 Mute (MUTE_xx)
Default = 0
0 - Disabled
1 - Enabled
Function:
The Digital-to-Analog converter output will mute when enabled. The quiescent voltage on the output will
be retained. The muting function is affected, similarly to attenuation changes, by the Soft and Zero Cross
bits. The MUTE pins will go active during the mute period according to the MUTEC bits.
DS670F2
41
CS4365
6.10
Mixing Control (address 0Ah, 0Dh, 10h, 13h)
7
6
5
4
3
2
1
0
Reserved
0
Px_DEM1
0
Px_DEM0
0
PxATAPI4
0
PxATAPI3
1
PxATAPI2
0
PxATAPI1
0
PxATAPI0
1
6.10.1 De-Emphasis Control (PX_DEM1:0)
Default = 00
00 - Disabled
01 - 44.1 kHz
10 - 48 kHz
11 - 32 kHz
Function:
Selects the appropriate digital filter to maintain the standard 15 μs/50 μs digital de-emphasis filter response at 32, 44.1 or 48 kHz sample rates. (see Figure 16)
De-emphasis is only available in Single-Speed Mode.
6.10.2 ATAPI Channel Mixing and Muting (ATAPI)
Default = 01001 - AOUTAx=aL, AOUTBx=bR (Stereo)
Function:
The CS4365 implements the channel-mixing functions of the ATAPI CD-ROM specification. The ATAPI
functions are applied per A-B pair. Refer to Table 9 and Figure 17 for additional information.
ATAPI4
ATAPI3
ATAPI2
ATAPI1
ATAPI0
AOUTAx
AOUTBx
0
0
0
0
0
MUTE
MUTE
0
0
0
0
1
MUTE
bR
0
0
0
1
0
MUTE
bL
0
0
0
1
1
MUTE
b[(L+R)/2]
0
0
1
0
0
aR
MUTE
0
0
1
0
1
aR
bR
0
0
1
1
0
aR
bL
0
0
1
1
1
aR
b[(L+R)/2]
0
1
0
0
0
aL
MUTE
0
1
0
0
1
aL
bR
0
1
0
1
0
aL
bL
0
1
0
1
1
aL
b[(L+R)/2]
0
1
1
0
0
a[(L+R)/2]
MUTE
0
1
1
0
1
a[(L+R)/2]
bR
0
1
1
1
0
a[(L+R)/2]
bL
0
1
1
1
1
a[(L+R)/2]
b[(L+R)/2]
1
0
0
0
0
MUTE
MUTE
1
0
0
0
1
MUTE
bR
1
0
0
1
0
MUTE
bL
Table 9. ATAPI Decode Table
42
DS670F2
CS4365
ATAPI4
ATAPI3
ATAPI2
ATAPI1
ATAPI0
AOUTAx
AOUTBx
1
0
0
1
1
MUTE
[(bL+aR)/2]
1
0
1
0
0
aR
MUTE
1
0
1
0
1
aR
bR
1
0
1
1
0
aR
bL
1
0
1
1
1
aR
[(aL+bR)/2]
1
1
0
0
0
aL
MUTE
1
1
0
0
1
aL
bR
1
1
0
1
0
aL
bL
1
1
0
1
1
aL
[(aL+bR)/2]
1
1
1
0
0
[(aL+bR)/2]
MUTE
1
1
1
0
1
[(aL+bR)/2]
bR
1
1
1
1
0
[(bL+aR)/2]
bL
1
1
1
1
1
[(aL+bR)/2]
[(aL+bR)/2]
Table 9. ATAPI Decode Table
6.11
Volume Control (address 0Bh, 0Ch, 0Eh, 0Fh, 11h, 12h)
7
6
5
4
3
2
1
0
xx_VOL7
0
xx_VOL6
0
xx_VOL5
0
xx_VOL4
0
xx_VOL3
0
xx_VOL2
0
xx_VOL1
0
xx_VOL0
0
These six registers provide individual volume and mute control for each of the six channels.
The values for “xx” in the bit fields above are as follows:
Register address 0Bh - xx = A1
Register address 0Ch - xx = B1
Register address 0Eh - xx = A2
Register address 0Fh - xx = B2
Register address 11h - xx = A3
Register address 12h - xx = B3
6.11.1
Digital Volume Control (xx_VOL7:0)
Default = 00h (0 dB)
Function:
The Digital Volume Control registers allow independent control of the signal levels in 1/2 dB increments
from 0 to -127.5 dB. Volume settings are decoded as shown in Table 10. The volume changes are implemented as dictated by the Soft and Zero Cross bits in the Power and Muting Control register. Note that
the values in the volume setting column in Table 10 are approximate. The actual attenuation is determined
by taking the decimal value of the volume register and multiplying by 6.02/12.
Binary Code
Decimal Value
Volume Setting
00000000
00000001
00000110
11111111
0
1
6
255
0 dB
-0.5 dB
-3.0 dB
-127.5 dB
Table 10. Example Digital Volume Settings
DS670F2
43
CS4365
6.12
PCM Clock Mode (address 16h)
7
6
5
4
3
2
1
0
Reserved
0
Reserved
0
MCLKDIV
0
Reserved
0
Reserved
0
Reserved
0
Reserved
0
Reserved
0
6.12.1 Master Clock DIVIDE by 2 ENABLE (MCLKDIV)
Function:
When set to 1, the MCLKDIV bit enables a circuit which divides the externally applied MCLK signal by 2
prior to all other internal circuitry.
When set to 0 (default), MCLK is unchanged.
44
DS670F2
CS4365
0
0
−20
−20
−40
−40
Amplitude (dB)
Amplitude (dB)
7. FILTER PLOTS
−60
−60
−80
−80
−100
−100
−120
0.4
−120
0.4
1
0.9
0.8
0.7
0.6
Frequency(normalized to Fs)
0.5
Figure 24. Single-Speed (fast) Stopband Rejection
0.42
0.44
0.46
0.48
0.5
0.52
Frequency(normalized to Fs)
0.54
0.56
0.58
0.6
Figure 25. Single-Speed (fast) Transition Band
0
0.02
−1
0.015
−2
0.01
0.005
−4
Amplitude (dB)
Amplitude (dB)
−3
−5
−6
0
−0.005
−7
−0.01
−8
−0.015
−9
−10
0.45
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
−0.02
0.55
0
0
−20
−20
−40
−40
−60
−80
−100
−100
0.5
0.8
0.7
0.6
Frequency(normalized to Fs)
0.9
1
Figure 28. Single-Speed (slow) Stopband Rejection
DS670F2
0.1
0.15
0.2
0.25
0.3
Frequency(normalized to Fs)
0.35
0.4
0.45
0.5
−60
−80
−120
0.4
0.05
Figure 27. Single-Speed (fast) Passband Ripple
Amplitude (dB)
Amplitude (dB)
Figure 26. Single-Speed (fast) Transition Band (detail)
0
−120
0.4
0.42
0.44
0.46
0.48
0.5
0.52
Frequency(normalized to Fs)
0.54
0.56
0.58
0.6
Figure 29. Single-Speed (slow) Transition Band
45
CS4365
0.02
0
−1
0.015
−2
0.01
−3
Amplitude (dB)
Amplitude (dB)
0.005
−4
−5
−6
0
−0.005
−7
−0.01
−8
−0.015
−9
−10
0.45
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
−0.02
0.55
Figure 30. Single-Speed (slow) Transition Band (detail)
0.1
0.15
0.2
0.25
0.3
Frequency(normalized to Fs)
0.35
0.4
0.45
0.5
0
20
20
40
40
Amplitude (dB)
Amplitude (dB)
0.05
Figure 31. Single-Speed (slow) Passband Ripple
0
60
60
80
80
100
100
120
0
120
0.4
0.5
0.6
0.7
0.8
Frequency(normalized to Fs)
0.9
1
Figure 32. Double-Speed (fast) Stopband Rejection
0.4
0.42
0.44
0.46
0.48
0.5
0.52
Frequency(normalized to Fs)
0.54
0.56
0.58
0.6
Figure 33. Double-Speed (fast) Transition Band
0
0.02
1
0.015
2
0.01
0.005
4
Amplitude (dB)
Amplitude (dB)
3
5
6
0
0.005
7
0.01
8
0.015
9
10
0.45
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
Figure 34. Double-Speed (fast) Transition Band (detail)
46
0.02
0
0.05
0.1
0.15
0.2
0.25
0.3
Frequency(normalized to Fs)
0.35
0.4
0.45
0.5
Figure 35. Double-Speed (fast) Passband Ripple
DS670F2
CS4365
0
20
20
40
40
Amplitude (dB)
Amplitude (dB)
0
60
60
80
80
100
100
120
120
0.2
0.3
0.4
0.5
0.6
0.7
Frequency(normalized to Fs)
0.8
0.9
1
Figure 36. Double-Speed (slow) Stopband Rejection
0.2
0.3
0.4
0.5
0.6
Frequency(normalized to Fs)
0.7
0.8
Figure 37. Double-Speed (slow) Transition Band
0
0.02
1
0.015
2
0.01
0.005
4
Amplitude (dB)
Amplitude (dB)
3
5
6
0
0.005
7
0.01
8
0.015
9
10
0.45
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
0.02
0.55
Figure 38. Double-Speed (slow) Transition Band (detail)
40
40
Amplitude (dB)
Amplitude (dB)
20
60
0.15
0.2
Frequency(normalized to Fs)
0.25
0.3
0.35
60
80
80
100
100
120
0.3
0.4
0.5
0.6
0.7
Frequency(normalized to Fs)
0.8
0.9
1
Figure 40. Quad-Speed (fast) Stopband Rejection
DS670F2
0.1
0
20
0.2
0.05
Figure 39. Double-Speed (slow) Passband Ripple
0
120
0
0.2
0.3
0.4
0.5
0.6
Frequency(normalized to Fs)
0.7
0.8
Figure 41. Quad-Speed (fast) Transition Band
47
CS4365
0.2
0
1
0.15
2
0.1
3
Amplitude (dB)
Amplitude (dB)
0.05
4
5
6
0
0.05
7
0.1
8
0.15
9
10
0.45
0.2
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
Figure 42. Quad-Speed (fast) Transition Band (detail)
0
0.05
0.1
0.15
Frequency(normalized to Fs)
0.2
0.25
Figure 43. Quad-Speed (fast) Passband Ripple
0
0
20
40
40
Amplitude (dB)
Amplitude (dB)
20
60
60
80
80
100
100
120
120
0.1
0.2
0.3
0.4
0.5
0.6
0.7
Frequency(normalized to Fs)
0.8
0.9
1
Figure 44. Quad-Speed (slow) Stopband Rejection
0.1
0.2
0.3
0.4
0.5
0.6
Frequency(normalized to Fs)
0.7
0.8
0.9
Figure 45. Quad-Speed (slow) Transition Band
0.02
0
1
0.015
2
0.01
0.005
4
Amplitude (dB)
Amplitude (dB)
3
5
6
0
0.005
7
0.01
8
0.015
9
10
0.45
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
Figure 46. Quad-Speed (slow) Transition Band (detail)
48
0.02
0
0.02
0.04
0.06
0.08
Frequency(normalized to Fs)
0.1
0.12
Figure 47. Quad-Speed (slow) Passband Ripple
DS670F2
CS4365
8. PARAMETER DEFINITIONS
Total Harmonic Distortion + Noise (THD+N)
The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified
bandwidth (typically 10 Hz to 20 kHz), including distortion components. Expressed in decibels.
Dynamic Range
The ratio of the full-scale rms value of the signal to the rms sum of all other spectral components over the
specified bandwidth. Dynamic range is a signal-to-noise measurement over the specified bandwidth
made with a -60 dBFS signal. 60 dB is then added to the resulting measurement to refer the measurement to full scale. This technique ensures that the distortion components are below the noise level and
do not affect the measurement. This measurement technique has been accepted by the Audio Engineering Society, AES17-1991, and the Electronic Industries Association of Japan, EIAJ CP-307.
Interchannel Isolation
A measure of crosstalk between the left and right channels. Measured for each channel at the converter's
output with all zeros to the input under test and a full-scale signal applied to the other channel. Units in
decibels.
Interchannel Gain Mismatch
The gain difference between left and right channels. Units in decibels.
Gain Drift
The change in gain value with temperature. Units in ppm/°C.
DS670F2
49
CS4365
9. PACKAGE DIMENSIONS
48L LQFP PACKAGE DRAWING
E
E1
D D1
1
e
B
∝
A
A1
L
DIM
MIN
INCHES
NOM
MAX
MIN
MILLIMETERS
NOM
MAX
A
A1
B
D
D1
E
E1
e*
L
µ
--0.002
0.007
0.343
0.272
0.343
0.272
0.016
0.018
0.000°
0.055
0.004
0.009
0.354
0.28
0.354
0.28
0.020
0.24
4°
0.063
0.006
0.011
0.366
0.280
0.366
0.280
0.024
0.030
7.000°
--0.05
0.17
8.70
6.90
8.70
6.90
0.40
0.45
0.00°
1.40
0.10
0.22
9.0 BSC
7.0 BSC
9.0 BSC
7.0 BSC
0.50 BSC
0.60
4°
1.60
0.15
0.27
9.30
7.10
9.30
7.10
0.60
0.75
7.00°
* Nominal pin pitch is 0.50 mm
*Controlling dimension is mm.
*JEDEC Designation: MS022
50
DS670F2
CS4365
10.ORDERING INFORMATION
Product
Description
CS4365
114 dB, 192 kHz 6-channel D/A Converter
CDB4365
CS4365 Evaluation Board
Package
Pb-Free
48-pin
LQFP
YES
-
Grade
Temp Range
Container
Tray
Commercial -40°C to +85°C
Tape & Reel
Tray
Automotive -40°C to +105°C
Tape & Reel
-
Order #
CS4365-CQZ
CS4365-CQZR
CS4365-DQZ
CS4365-DQZR
CDB4365
11.REFERENCES
1. How to Achieve Optimum Performance from Delta-Sigma A/D & D/A Converters, by Steven Harris. Paper
presented at the 93rd Convention of the Audio Engineering Society, October 1992.
2. CDB4365 data sheet, available at http://www.cirrus.com.
3. Design Notes for a 2-Pole Filter with Differential Input, by Steven Green. Cirrus Logic Application Note AN48
4. The I²C-Bus Specification: Version 2.0, Philips Semiconductors, December 1998.
http://www.semiconductors.philips.com.
12.REVISION HISTORY
Release
PP3
Changes
Updated Guaranteed Operational Temperature Range in “Recommended Operating Conditions” on page 8.
Updated VA, VLC, and VLS current cunsumption specs
Updated Fullscale output level
Updated Dynamic perforamnce limits.
Removed VOH specification
Updated VOL specification
F1
Updated “Recommended Operating Conditions” on page 8
Updated “DAC Analog Characteristics - Commercial (-CQZ)” on page 9
Updated “DAC Analog Characteristics - Automotive (-DQZ)” on page 10
Updated “Power and Thermal Characteristics” on page 11
Updated Legal Information on page 52
Removed TDM Mode functionality
F2
Updated “DAC Pair Disable (DACx_DIS)” on page 35
Updated “Digital Interface Format (DIF)” on page 35
Added PCM mode format changeable in reset only to “Mode Select” on page 22
Updated Package Thermal Resistance in “Power and Thermal Characteristics” on page 11
DS670F2
51
CS4365
Contacting Cirrus Logic Support
For all product questions and inquiries, contact a Cirrus Logic Sales Representative.
To find the one nearest to you, go to www.cirrus.com
IMPORTANT NOTICE
Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject
to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant
information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale
supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus
for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third
parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights,
copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent
does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE
IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER’S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY
INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS’ FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES.
Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks
or service marks of their respective owners.
I²C is a registered trademark of Philips Semiconductor.
SPI is a trademark of Motorola, Inc.
52
DS670F2