CONNOR-WINFIELD AGOF5S3P

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX
(630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
CRYSTAL CONTROLLED OSCILLATORS
14 PIN DIP 5.0V STRATUM 3 PLUS HCMOS OCXO
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Storage Temperature
TABLE 1.0
UNITS
MINIMUM
-40
NOMINAL
-
MAXIMUM
85
UNITS
°C
(Vcc)
-0.5
-
7.0
Vdc
NOMINAL
(Fo)
MAXIMUM
20.00
UNITS
Center Frequency
Frequency Calibration
Frequency vs. Change in Temperature
Frequency vs. Change in Supply Voltage
Frequency vs. Change in Load
Frequency Aging Daily
Frequency Aging per year
Total Frequency Tolerance
Operating Temperature Range
MINIMUM
9.00
Supply Voltage
Supply Current
Supply Current Steady State @25°C
Supply Voltage
OPERATING SPECIFICATIONS
CW 0107
AGOF5S3P
10.00M
NOTE
TABLE 2.0
PARAMETER
-0.30
-0.21
-0.05
-0.02
-0.2
-1.5
-20
-
(Vcc)
4.75
(Icc)
-
(Icc)
Allan Variance (1 second)
Jitter (10Hz to 10 MHz)
SSB Phase Noise at 1Hz offset
SSB Phase Noise at 10Hz offset
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at 10KHz offset
Start Up Time: Oscillator
Warm Up Time
Retrace
TDEV @ 1.0 Sec.
TDEV @ 4.0 Sec.
0.30
0.21
0.05
0.02
2
0.2
1.5
70
MHz
ppm
ppm
ppm
ppm
ppb/day
ppm
ppm
°C
5.00
5.25
Vdc
-
300
mA
-
75
-
mA
-
5.00E-10
-
-0.3
-
-70
-100
-125
-140
-150
-
1
10
5
0.3
1
2
AGOF5S3P
NOTE
1
2
3
4
DESCRIPTION
The Connor-Winfield
AGOF5S3P is a hermetically
sealed 14 Pin DIP, 5.0V Oven
Controlled Crystal Oscillator
(OCXO) with a HCMOS / TTL
compatible output. The
AGOF5S3P is designed for
higher stability Stratum 3 Plus
applications requiring low
jitter and tight calibration.
5
ps RMS
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
mS
Minutes
ppm
nS
nS
FEATURES
6
7
5.0V OPERATION
FREQUENCY STABILITY ±0.21ppm
TEMPERATURE RANGE: -20 to 70°C
HCMOS OUTPUT CHARACTERISTICS
PARAMETER
LOAD
Voltage
(High)
(Low)
(Voh)
(Vol)
Current
(High)
(Low)
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
TABLE 3.0
MINIMUM
12
4.75
-
NOMINAL
15
-
MAXIMUM
18
0.4
UNITS
pf
Vdc
Vdc
-4
45
-
50
-
4
55
6
mA
mA
%
nS
(Ioh)
(Ioh)
OVERALL FREQUENCY TOLERANCE :
±1.5ppm over Twenty Years.
8
8
OVERALL AGING: ±0.5ppm over Twenty
Years
RoHS 5/6 COMPLIANT
TABLE 4.0
PACKAGE CHARACTERISTICS
Package
NOTE
14 pin DIP, hermetically sealed, grounded case, welded package
Notes:
1)
2)
3)
4)
5)
Initial calibration @ 25C at time of shipment.
Frequency vs. temperature stability, -20 to 70°C absolute.
Frequency stability per 5% change in supply voltage.
Frequency stability per 5% change in load
Inclusive of calibration, operating temperature range, supply voltage change, load change, shock
and vibration and aging over 20 years.
6) Measured @ 25C, within 5 minutes, the unit will be within +/-0.5ppm of nominal.
7) 24 hours off then 60 minutes on at a constant temperature and voltage.
8) Supply voltage at 5.00 Vdc.
ORDERING INFORMATION
AGOF5S3P
OCXO
SERIES
- 10.00MHz
CENTER
FREQUENCY
Specifications subject to change without notice.
DATA SHEET #:
Cx039
PAGE 1
OF
2
REV: 02
DATE:
08/31/07
aCopyright 2007 Connor-Winfield all rights reserved.
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX
(630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
CRYSTAL CONTROLLED OSCILLATORS
ENVIRONMENTAL CHARACTERISTICS
Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 20 cycles,10 minute dwell, 1minute
transition.
Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No bubbles in flourinert (FC-43) at 125°C ±5°C for 20
seconds.
SOLDERING
Pin Solderability: Per MIL-STD-883, Method 200. 8 hour steam age prior to 254°C ±5°C Solder pot dip, 95% Coverage.
Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board-mount product, 260°C
±5°C for 20 Seconds.
MECHANICAL CHARACTERISTICS
Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak, 10Hz to 500Hz, 15minute cycles 12 times each
perpendicular axis.
Shock: Per MIL-STD-202, Method 213, Condition D. 500G’s, 1ms, halfsine, 3 shocks per direction.
Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C.
Package Outline and Pin Connections
Solder Profile
Test Circuit
Temperature
225°C
Ramp-Up Rate
3°C/second max.
from 150°C to 225°C.
225°C
tp
Ramp-Down Rate
6°C/second max.
183°C
150°C
100°C
25°C
0
Time
60-120s
Max.
10-30s
60-150s Max.
360 Sec. Max.
Specifications subject to change without notice.
DATA SHEET #:
Cx039
PAGE 2
OF
2
REV:
02
DATE:
08/31/07
aCopyright 2007 Connor-Winfield all rights reserved.