CONNOR-WINFIELD OFC5DJ3BS

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX
(630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
ABSOLU TE MAX IMUM RATING S
PARAMETER
Storage Temperature
Supply Voltage
(Vcc)
MINIMUM
-40
-0.5
NOMINAL
-
MAXIMUM
85
7
UNITS
°C
Vdc
(Fo)
MINIMUM
10
NOMINAL
-
MAXIMUM
20
UNITS
MHz
OPERATING SPECIFIC ATIONS
Standard Frequencies Available:
Frequency Calibration
Frequency vs. Temperature Stability
Frequency vs. Voltage Stability (+/-5%)
Frequency vs. Load Stability (+/-5%)
Aging: Daily
Aging: First Year
Aging: Long Term (20 Years)
Total Frequency Tolerance (20 years)
Allen Variance: 1 second, 100 average.
Operating Temperature Range
Supply Voltage
Power Consumption: Turn On
Power Consumption: Steady-State
Start-Up Time
Warm Up
10.00M
TABLE 1.0
UNITS
PARAMETER
Center Frequency
CW 0534
SURFACE MOUNT 5.0V OCXO with SINEWAVE OUTPUT
OFC5DJ3BS
CRYSTAL CONTROLLED OSCILLATORS
NOTE
TABLE 2.0
(Vcc)
10 MHZ, 13 MHz, 15 MHZ, or 20 MHz
-0.2
0.2
ppm
-20
20
ppb
-2
2
ppb
-2
2
ppb
-1
1
ppb/day
-50
50
ppb
-250
250
ppb
-500
500
ppb
1.00E-10
RMS
-20
70
°C
4.75
5.00
5.25
Vdc
3.75
W
1. 5
W
500
mS
-100
100
ppb
SINEWAVE OUTPUT CHARACTERISTICS
NOTE
1
2
3
4
5
6
6
7
8
OFC5DJ3BS
DESCRIPTION
The Connor-Winfield
OFC5DJ3BS is a 5V Surface
Mount Oven Controlled Crystal
Oscillator (OCXO) with a
Sinewave output. The
OFC5J3BS is designed for
Wireless applications requiring
low Phase Noise and tight
frequency stability.
FEATURES
TABLE 3.0
PARAMETER
LOAD
Output Power
Spurious Output
SSB Phase Noise at 1Hz offset
SSB Phase Noise at 10Hz offset
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
MINIMUM
45
0
NOMINAL
50
3
-85
-110
-135
-150
MAXIMUM
55
-80
-
UNITS
Ohms
dBm
dBc
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
-
SSB Phase Noise at 10KHz offset
-
-155
-
dBc/Hz
RESTABILIZATION TIME
Off Time
< 1 Hour
< 6 Hours
< 24 Hours
1 to 16 Days
> 16 Days
NOTE
FREQUENCY STABILITY: ±20ppb
TEMERATURE RANGE: -20 to 70°C
5.0V OPERATION
SINEWAVE OUTPUT
TABLE 4. 0
NOTE
9
9
9
9
9
Restabilization Time
< 2 Hours
< 12 Hours
< 48 Hours
48 Hours + ¼ Off Time
< 6 Days
FIXED FREQUENCY OCXO
LOW PHASE NOISE
SURFACE MOUNT PACKAGE
TAPE AND REEL PACKAGING
PACKAG E CHARACTERISTICS
TABLE 5.0
Non-hermetic package consisting of an FR4 substrate with grounded metal
cover.
ENVIRONMNETAL CHARACTERISTICS
TABLE 6.0
Shock
100G’s, 6mS, halfsine per MIL-STD-202F, Method 213B, Test Condition C
Vibration
0.06” D.A. or 10G peak 10 to 500 Hz, per MIL-STD-202F, Method 204D,
Test condition A
PROCESS RECOMMENDATIONS
TABLE 7.0
Solder Reflow
The component solder used internal to this device has a melting point of
221°C. The peak temperature inside the device should be less than or equal
to 220°C for a maximum of 10 seconds
Wash
Ultrasonic cleaning is not recommended.
Package
ORDERING INFORMATION
OFC5DJ3BS
OCXO
SERIES
- 10.00MHz
CENTER
FREQUENCY
Specifications subject to change without notice.
DATA SHEET #:
Cx067
PAGE 1
OF
2
REV: 04
DATE:
03/09/07
aCopyright 2001 Connor-Winfield all rights reserved.
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX
(630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
PRODUCT
D ATA
SHEET
CRYSTAL CONTROLLED OSCILLATORS
PIN CONNECTIONS
Notes:
1)
2)
3)
4)
5)
6)
7)
8)
9)
TABLE 8.0
Pin
1
2
6
7
8
9
10
11
12
13
14
15
16
Labels will include the calibr ation frequency at the time of ship.
Initial calibration @ 25°C at the time of shipment.
Overall frequency stability ref erenced to measurement at 25°C.
After ten days of continuous operation.
Inclusive of calibration, freq uency stability vs. change in tem perature, supply voltage
change, load change, hock and vibration, 20 years aging.
Vcc = 5.0Vdc.
From Vcc=90% of final value. No m ore than 16 transitions at start-up before oscillator
has started.
Measured @ 0°C, within 5 minutes, refer enced one hour after turn-on.
For a given off time, the time r equired to meet daily aging, short-term stability.
Function
N/C
Ground
N/C
Ground
Vcc
Vcc
Ground
Ground
N/C
Ground
Output
Ground
N/C
SUGGESTED PAD LAYOUT
PACKAGE LAYOUT
.310
(7.87mm)
10.00M
OFC5DJ3BS
CW
DATE CODE
12.7
.110
(2.75mm)
.210
(5.33mm)
.110
(2.75mm)
Pin 1
Dimensional Tolerance:
±.005 (.127mm)
.210
(5.33mm)
KEEP OUT AREAS (3 PLACES)
TEST CIRCUIT
SOLDER PROFILE
Temperature
225°C
Vcc
Vcc
10 GND
GND 7
11 GND
NC 6
Ramp-Up Rate
3°C/second max.
from 150°C to 225°C.
225°C
tp
Ramp-Down Rate
6°C/second max.
183°C
150°C
12 NC
13 GND
100°C
14 OUT
15 GND
GND 2
NC
NC
25°C
0
50 Ohm
Time
60-120s
Max.
10-30s
60-150s Max.
360 Sec. Max.
Specifications subject to change without notice.
DATA SHEET #:
Cx067
PAGE 2
OF
2
REV: 04
DATE:
03/09/07
aCopyright 2001 Connor-Winfield all rights reserved.