PB8 MOUNTING BOARD • Plug-compatible logic connections • Screw terminal barrier block for load connections • Resident pull-up resistors • 5 amp field-replaceable fuses • All even-numbered logic connections are logic ground Input and output modules accepted interchangeably Operate with 5, 15 or 24 volt logic supplies Captive-screw retaining system for standard-size modules • • • (LITTLEFUSE #251005 or equivalent) • LEDs indicate logic status MECHANICAL SPECIFICATIONS SCREW TERMINAL LOGIC SUPPLY BARRIER STRIP 6-32 SCREW TERMINAL POWER BARRIER STRIP (see note 2) 8.0 (203,2) DIMENSIONS: INCHES (MILLIMETERS) TOLERANCE:+-0.020 ( +- 0,50) 7.5 (190,5) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 - + REPLACEABLE 5 AMP LINE FUSE (8) (see note 4) GORDOS DIGITAL I/O MODULES SOLD SEPERATELY 0.3 (7,6) 0 1 2 3 4 5 6 3.5 (88,9) SWAGED STANDOFF THRU HOLE 0.15 (3,2) DIA. (4) 3.0 (76,2) 2.6 (66,0) 1.4 (35,6) 7 PULL UP RESISTORS 3.3K OHM (8) 0.45 (11,4) 0.75 (19,1) SIGNAL INPUT/OUTPUT 50 TRACE (0.1" CENTERS) MALE CARD EDGE (see note 1) 2.2 (55,9) LED STATUS INDICATORS (8) NOTES: 1) MATING CONNECTOR IS BERG 66317-150 OR EQUIVALENT. SPECIFY SUFFIX "V" FOR OPTIONAL CA26HM-2F-SR CIRCUIT ASSEMBLY OR EQUIVALENT 26 CONDUCTOR PERPENDICULAR-TO-THE-BOARD MALE PIN CONNECTOR. 2) 6-32 SCREW TERMINAL BARRIER STRIPS ACCEPT WIRE SIZES FROM 24 TO 12 AWG. 3) OPTIONAL JUMPERS ARE AVAILABLE TO INTERCONNECT BARRIER STRIP COMMONS. ORDER 1 EACH "JS8". 4) LITTLE FUSE 251005 OR EQUIVALENT. LOGIC SUPPLY BARRIER STRIP 1 2 + BOTTOM ALL EVEN PINS “V” OR “C” OPTION EDGE CONN TOP + LOGIC 49 25 SIGNAL INPUT/OUTPUT 50 TRACE (0.1" CENTERS) MALE CARD EDGE OR OPTIONAL PIN CONNECTOR +LOGIC APPROVALS UL E79183 CSA 38595 47 45 43 41 39 37 35 33 25 1 3 4 5 6 POWER BARRIER STRIP 7 8 9 10 1112 1314 5 AMP LINE FUSE 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 5 5 5 5 5 5 5 5 23 21 19 17 15 13 11 9 1 CUSTOMER INSTALLED OPTIONAL JUMPERS FOR CONNECTING LOGIC SUPPLY THRU CARD EDGE CONNECTOR 15 16 I/O MODULE PIN SOCKETS AMP #645979-1 OR EQUIVALENT LED STATUS INDICATOR (8) PULL UP RESISTOR 3.3K OHM (8) Rev. 070808 DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / PERIGO HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. x Disconnect all power before installing or working with this equipment. x Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. x Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. x Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION x Eteindre toutes les sources d'énergie de cet appareil avant de travailler dessus de cet appareil x Vérifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lésions sérieuses sérieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. x Stellen Sie jeglichen Strom ab, der dieses Gerät versorgt, bevor Sie an dem Gerät Arbeiten durchführen x Vor dem Drehen auf Energie alle Anschlüsse überprüfen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen können zum Tode oder zu schweren Verletzungen führen. RISCHIO DI SCOSSA ELETTRICA O DELL’ESPLOSI ONE. x Spenga tutta l'alimentazion e che fornisce questa apparecchiatu ra prima del lavorare a questa apparecchiatu ra x Verificare tutti i collegamenti e sostituire tutte le coperture prima della rotazione sull'alimentazi one L'omissione di seguire queste istruz ioni provocherà la morte o di lesioni serie RISCO DE DESCARGA ELÉTTRICA OU EXPLOSÃO x Desconectar o equipamento de toda á energia antes de instalar ou trabalhar com este equipamen to x Verificar todas as conexões e recolocar todas as tampas antes de religar o equipamento O não cumprimento destas instruções pode levar á morte ou lesões sérias. ANNEX - ENVIROMENTAL INFORMATION