HM5113165FTD-6 EO 128M EDO DRAM (8-Mword × 16-bit) 4k refresh E0177H10 (Ver. 1.0) Jul. 5, 2001 L Description The HM5113165F is 128M-bit dynamic R AM orga nized as 8, 388,608-w ord × 16-bit. It has re alize d high per forma nce and low powe r by employing C MOS proc ess tec hnology. HM5113165F off ers Extende d Da ta Out (EDO) Page Mode as a high speed access mode. It is packaged in 50-pin plastic TSOPII. Pr Features od • Single 3.3 V supply: 3.3 V ± 0.3 V • Access time: 60 ns (max) • Power dissipation ⎯ Active: 828 mW (max) ⎯ Standby : 3.6 mW (max) (CMOS interface) • EDO page mode capability • Refresh cycles ⎯ RAS-only refresh 4096 cycles /64 ms ⎯ CBR/Hidden refresh 4096 cycles /64 ms • 4 variations of refresh ⎯ RAS-only refresh ⎯ CAS-before-RAS refresh ⎯ Hidden refresh • 2CAS-byte control t uc Ordering Information Type No. Access time Package HM5113165FTD-6 60 ns 400-mil 50-pin plastic TSOP II (TTP-50DE) This product became EOL in December, 2006. Elpida Memory, Inc. is a joint venture DRAM company of NEC Corporation and Hitachi, Ltd. HM5113165FTD-6 Pin Arrangement (HM5113165F Series) 50-pin TSOP L EO 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 VSS I/O15 I/O14 I/O13 I/O12 VSS I/O11 I/O10 I/O9 I/O8 NC VSS LCAS UCAS OE NC NC NC A11 A10 A9 A8 A7 A6 VSS od Pr VCC I/O0 I/O1 I/O2 I/O3 VCC I/O4 I/O5 I/O6 I/O7 NC VCC WE RAS NC NC NC NC A0 A1 A2 A3 A4 A5 VCC (Top view) Pin Description Pin name A0 to A11 Function I/O0 to I/O15 Data input/output RAS Row address strobe UCAS, LCAS Column address strobe WE Write enable OE Output enable VCC Power supply VSS Ground NC No connection Data Sheet E0177H10 2 t uc Address input — Row/Refresh address A0 to A11 — Column address A0 to A10 HM5113165FTD-6 Block Diagram Column decoder A0 EO A1 to • • • Column address buffers 8M array 8M array A10 Row address buffers Row decoder 8M array L 8M array I/O buffers 8M array I/O8 to I/O15 8M array 8M array 8M array Pr Timing and control RAS UCAS LCAS WE OE Lower pellet od Timing and control Column decoder Column address buffers 8M array 8M array • • • Row address buffers 8M array 8M array 8M array 8M array 8M array t uc 8M array Row decoder A11 Upper pellet I/O buffers I/O0 to I/O7 Data Sheet E0177H10 3 HM5113165FTD-6 Operation Table LCAS UCAS WE OE I/O 0 to I/O 7 I/O 8 to I/O 15 Operation H × × × × High-Z High-Z Standby L L H H L Dout High-Z Read cycle L H L H L High-Z Dout L L L H EO RAS L L L H H L L Dout Dout L* 2 × Din × L* 2 × × Din 2 × Din Din L L L* L L H L* 2 H Din × L L* 2 H × Din L L* 2 H Din Din H H to L L to H Dout/Din High-Z L H to L L to H High-Z Dout/Din L H L L Early write cycle Delayed write cycle L L L L H L L L H to L L to H Dout/Din Dout/Din L H H × × High-Z High-Z RAS-only refresh cycle H to L L L H × High-Z High-Z CAS-before-RAS refresh cycle L L L H H High-Z High-Z Read cycle (Output disabled) Pr L Read-modify-write cycle od Notes: 1. H: VIH (inactive) L: VIL (active) ×: VIH or VIL 2. t WCS ≥ 0 ns: Early write cycle t WCS < 0 ns: Delayed write cycle 3. UCAS controls the upper pellet (I/O 8 to 15) only, and LCAS controls the lower pellet (I/O 0 to 7) only. Therefore, mode, read/write and High-Z control are done independently by each UCAS, LCAS. t uc Data Sheet E0177H10 4 HM5113165FTD-6 Absolute Maximum Ratings Symbol Value Unit Terminal voltage on any pin relative to VSS VT –0.5 to VCC + 0.5 (≤ 4.6 V (max)) V Power supply voltage relative to VSS VCC –0.5 to +4.6 V Short circuit output current Iout 50 mA Power dissipation PT 1.0 W Storage temperature Tstg –55 to +125 °C EO Parameter DC Operating Conditions L Parameter Min Typ Max Unit Notes VCC 3.0 3.3 3.6 V 1, 2 VSS 0 0 0 V 2 Input high voltage VIH 2.0 — VCC + 0.3 V 1 Input low voltage VIL –0.3 — 0.8 V 1 Ta 0 — 70 ˚C Supply voltage Ambient temperature range Pr Symbol Notes: 1. All voltage referred to VSS . 2. The supply voltage with all VCC pins must be on the same level. The supply voltage with all VSS pins must be on the same level. od t uc Data Sheet E0177H10 5 HM5113165FTD-6 DC Characteristics HM5113165F -6 EO Parameter 1, Operating current* * 2 Standby current Min Max Unit Test conditions I CC1 — 230 mA t RC = min I CC2 — 4 mA TTL interface RAS, UCAS, LCAS = VIH Dout = High-Z — 1 mA CMOS interface RAS, UCAS, LCAS ≥ VCC – 0.2 V Dout = High-Z I CC3 — 230 mA t RC = min I CC5 — 10 mA RAS = VIH UCAS, LCAS = VIL Dout = enable I CC6 — 230 mA t RC = min L Symbol RAS-only refresh current* 2 Standby current* 1 Pr CAS-before-RAS refresh current I CC7 — 200 mA RAS = VIL , CAS cycle, t HPC = t HPC min Input leakage current I LI –5 5 µA 0 V ≤ Vin ≤ VCC + 0.3 V I LO –5 5 µA 0 V ≤ Vout ≤ VCC Dout = disable Output high voltage VOH 2.4 Output low voltage VOL 0 Output leakage current od EDO page mode current* 1, * 3 VCC V High Iout = –2 mA 0.4 V Low Iout = 2 mA Notes: 1. I CC depends on output load condition when the device is selected. I CC max is specified at the output open condition. 2. Address can be changed once or less while RAS = VIL. 3. Measured with one sequential address change per EDO cycle, t HPC . 4. VIH ≥ VCC – 0.2 V, 0 V ≤ VIL ≤ 0.2 V. Parameter Symbol Min Typ Input capacitance (Address) CI1 — — Input capacitance (Clocks) CI2 — — Output capacitance (Data-in, Data-out) CI/O — — t uc Capacitance (Ta = 25°C, VCC = 3.3 V ± 0.3 V) Max Unit Notes 7 pF 1 7 pF 1 7 pF 1, 2 Notes : 1. Capacitance measured with Boonton Meter or effective capacitance measuring method. 2. RAS, UCAS and LCAS = VIH to disable Dout. Data Sheet E0177H10 6 HM5113165FTD-6 AC Characteristics (Ta = 0 to +70˚C, VCC = 3.3 V ± 0.3 V, VSS = 0 V) *1, *2, *19 Test Conditions Input rise and fall time: 2 ns Input pulse levels: VIL = 0 V, VIH = 3.0 V Input timing reference levels: 0.8 V, 2.0 V Output timing reference levels: 0.8 V, 2.0 V Output load: 1 TTL gate + C L (100 pF) (Including scope and jig) EO • • • • • Read, Write, Read-Modify-Write and Refresh Cycles (Common parameters) L Parameter HM5113165F -6 Min Max Unit Random read or write cycle time t RC 104 — ns RAS precharge time t RP 40 — ns t CP 10 — ns t RAS 60 10000 ns t CAS 10 10000 ns t ASR 0 — ns t RAH 10 — ns CAS precharge time RAS pulse width CAS pulse width Row address setup time Row address hold time t ASC Column address hold time t CAH RAS to CAS delay time t RCD RAS to column address delay time t RAD RAS hold time t RSH CAS hold time t CSH CAS to RAS precharge time Notes 23 0 — ns 23 10 — ns 23 14 45 ns 3 12 30 ns 4 15 — ns 40 — ns t CRP 5 — OE to Din delay time t OED 15 — OE delay time from Din t DZO 0 — CAS delay time from Din t DZC 0 — Transition time (rise and fall) tT 2 50 t uc Column address setup time od Pr Symbol ns 23 ns 5 ns 6 ns 6 ns 7 Data Sheet E0177H10 7 HM5113165FTD-6 Read Cycle HM5113165F -6 Symbol Min Max Unit Notes Access time from RAS t RAC — 60 ns 8, 9 Access time from CAS t CAC — 15 ns 9, 10, 17 Access time from address t AA — 30 ns 9, 11, 17 Access time from OE t OEA — 15 ns 9 Read command setup time t RCS 0 — ns 23 Read command hold time to CAS t RCH 0 — ns 12, 23 Read command hold time from RAS t RCHR 60 — ns Read command hold time to RAS t RRH 0 — ns Column address to RAS lead time t RAL 30 — ns Column address to CAS lead time t CAL 18 — ns CAS to output in low-Z t CLZ 0 — ns t OH 3 — ns Output data hold time from OE t OHO 3 — ns Output buffer turn-off time t OFF — 15 ns 13, 21 t OEZ — 15 ns 13 t CDD 15 — ns 5 L EO Parameter Output buffer turn-off to OE CAS to Din delay time Output data hold time from RAS t OHR Output buffer turn-off to RAS t OFR Output buffer turn-off to WE t WEZ WE to Din delay time t WED RAS to Din delay time t RDD od Pr Output data hold time 12 21 3 — ns 21 — 15 ns 13, 21 — 15 ns 13 15 — ns 15 — ns t uc Data Sheet E0177H10 8 HM5113165FTD-6 Write Cycle HM5113165F -6 Symbol Min Max Unit Notes Write command setup time t WCS 0 — ns 14, 23 Write command hold time t WCH 10 — ns 23 Write command pulse width t WP 10 — ns Write command to RAS lead time t RWL 15 — ns Write command to CAS lead time t CWL 10 — ns 23 Data-in setup time t DS 0 — ns 15, 23 Data-in hold time t DH 10 — ns 15, 23 Notes L EO Parameter Read-Modify-Write Cycle Pr HM5113165F -6 Parameter Min Max Unit t RWC 140 — ns RAS to WE delay time t RWD 79 — ns 14 t CWD 34 — ns 14 49 — ns 14 15 — ns CAS to WE delay time Column address to WE delay time t AWD OE hold time from WE t OEH Refresh Cycle od Symbol Read-modify-write cycle time -6 t uc HM5113165F Parameter Symbol Min Max Unit Notes CAS setup time (CBR refresh cycle) t CSR 5 — ns 23 CAS hold time (CBR refresh cycle) t CHR 10 — ns 23 WE setup time (CBR refresh cycle) t WRP 0 — WE hold time (CBR refresh cycle) t WRH 10 — RAS precharge to CAS hold time t RPC 5 — ns ns ns 23 Data Sheet E0177H10 9 HM5113165FTD-6 EDO Page Mode Cycle HM5113165F -6 Symbol Min Max Unit Notes EDO page mode cycle time t HPC 25 — ns 20 EDO page mode RAS pulse width t RASP — 100000 ns 16 Access time from CAS precharge t CPA — 35 ns 9, 17, 23 RAS hold time from CAS precharge t CPRH 35 — ns Output data hold time from CAS low t DOH 3 — ns CAS hold time referred OE t COL 10 — ns CAS to OE setup time t COP 5 — ns Read command hold time from CAS precharge t RCHC 35 — ns Write pulse width during CAS precharge t WPE 10 — ns OE precharge time 10 — ns L EO Parameter t OEP 9, 22 Pr EDO Page Mode Read-Modify-Write Cycle HM5113165F -6 od Parameter Symbol EDO page mode read-modify-write cycle t HPRWC time WE delay time from CAS precharge t CPW Max Unit 68 — ns 54 — ns Parameter Symbol Max Refresh period t REF 64 Notes 14, 23 t uc Refresh Min Unit Notes ms 4096 cycles Notes: 1. AC measurements assume t T = 2 ns. 2. An initial pause of 200 µs is required after power up followed by a minimum of eight initialization cycles (any combination of cycles containing RAS-only refresh or CAS-before-RAS refresh). 3. Operation with the t RCD (max) limit insures that t RAC (max) can be met, t RCD (max) is specified as a reference point only; if t RCD is greater than the specified t RCD (max) limit, than the access time is controlled exclusively by t CAC . Data Sheet E0177H10 10 HM5113165FTD-6 L EO 4. Operation with the t RAD (max) limit insures that t RAC (max) can be met, t RAD (max) is specified as a reference point only; if t RAD is greater than the specified t RAD (max) limit, then access time is controlled exclusively by t AA . 5. Either t OED or t CDD must be satisfied. 6. Either t DZO or t DZC must be satisfied. 7. VIH (min) and VIL (max) are reference levels for measuring timing of input signals. Also, transition times are measured between VIH (min) and VIL (max). 8. Assumes that t RCD ≤ t RCD (max) and t RAD ≤ t RAD (max). If t RCD or t RAD is greater than the maximum recommended value shown in this table, t RAC exceeds the value shown. 9. Measured with a load circuit equivalent to 1 TTL loads and 100 pF. 10. Assumes that t RCD ≥ t RCD (max) and t RCD + t CAC (max) ≥ t RAD + t AA (max). 11. Assumes that t RAD ≥ t RAD (max) and t RCD + t CAC (max) ≤ t RAD + t AA (max). 12. Either t RCH or t RRH must be satisfied for a read cycles. 13. t OFF (max), t OEZ (max), t WEZ (max) and t OFR (max) define the time at which the outputs achieve the open circuit condition and are not referred to output voltage levels. 14. t WCS , t RWD, t CWD, t AWD and t CPW are not restrictive operating parameters. They are included in the data sheet as electrical characteristics only; if t WCS ≥ t WCS (min), the cycle is an early write cycle and the data out pin will remain open circuit (high impedance) throughout the entire cycle; if t RWD ≥ t RWD (min), t CWD ≥ t CWD (min), and t AWD ≥ t AWD (min), or t CWD ≥ t CWD (min), t AWD ≥ t AWD (min) and t CPW ≥ t CPW (min), the cycle is a read-modify-write and the data output will contain data read from the selected cell; if neither of the above sets of conditions is satisfied, the condition of the data out (at access time) is indeterminate. 15. t DS and t DH are referred to UCAS and LCAS leading edge in early write cycles and to WE leading edge in delayed write or read-modify-write cycles. 16. t RASP defines RAS pulse width in EDO page mode cycles. 17. Access time is determined by the longest among t AA , t CAC and t CPA. 18. In delayed write or read-modify-write cycles, OE must disable output buffer prior to applying data to the device. 19. When output buffers are enabled once, sustain the low impedance state until valid data is obtained. When output buffer is turned on and off within a very short time, generally it causes large VCC/V SS line noise, which causes to degrade VIH min/VIL max level. 20. t HPC (min) can be achieved during a series of EDO page mode write cycles or EDO page mode read cycles. If both write and read operation are mixed in a EDO page mode RAS cycle (EDO page mode mix cycle (1), (2)), minimum value of CAS cycle (tCAS + t CP + 2 t T) becomes greater than the specified t HPC (min) value. The value of CAS cycle time of mixed EDO page mode is shown in EDO page mode mix cycle (1) and (2). 21. Data output turns off and becomes high impedance from later rising edge of RAS and CAS. Hold time and turn off time are specified by the timing specifications of later rising edge of RAS and CAS between t OHR and t OH and between t OFR and t OFF. 22. t DOH defines the time at which the output level go cross. VOL = 0.8 V, VOH = 2.0 V of output timing reference level. 23. t ASC, t CAH , t RCS , t WCS , t WCH, t CSR , t RPC , t CRP , t CHR, t RCH, t CPA, t CPW , t CWL, t DH, t DS, t CHS and t CP are determined by each of UCAS /LCAS independently. 24. XXX: H or L (H: VIH (min) ≤ VIN ≤ VIH (max), L: VIL (min) ≤ VIN ≤ VIL (max)) ///////: Invalid Dout When the address, clock and input pins are not described on timing waveforms, their pins must be applied VIH or VIL. od Pr t uc Data Sheet E0177H10 11 HM5113165FTD-6 Timing Waveforms*24 Read Cycle EO tRC tRAS tRP RAS tCSH tT tASR tRAD tRAH tRAL tCAL tASC tCAH Pr Address tRSH tCAS L CAS tCRP tRCD Column Row tRRH tRCHR tRCS od WE tRCH tDZC tCDD tWED tRDD High-Z tDZO tOEA OE tCAC tAA tRAC tCLZ t uc ; Din tOED tOEZ tOHO tOFF tOH tOFR tOHR tWEZ Dout Dout Data Sheet E0177H10 12 HM5113165FTD-6 Early Write Cycle tRC tRAS tRP EO RAS tCSH tCRP tRCD tRSH tCAS tT CAS L tASR tASC tCAH Pr Address tRAH Row Column tWCS tDS tDH Din High-Z* Dout t uc Din od WE tWCH * t WCS t WCS (min) Data Sheet E0177H10 13 HM5113165FTD-6 Delayed Write Cycle*18 tRC tRAS tRP EO RAS tCSH tCRP tRCD tRSH tCAS tT CAS L tRAH tASR Address tASC Row tCAH Column Pr tRCS WE High-Z tDS tDH Din tOED tDZO tOEH tOEP OE tOEZ tCLZ High-Z Dout Invalid Dout Data Sheet E0177H10 14 t uc ; Din tRWL tWP od tDZC tCWL HM5113165FTD-6 Read-Modify-Write Cycle*18 tRWC tRAS tRP EO RAS tT tRCD L CAS tASR Address tCAS tCRP tRAD tASC tRAH Row tCAH Column Pr tCWL tCWD tRCS tRWL tWP tAWD tRWD WE od tDZC tDH tDS High-Z Din ; Din tOED tOEH tOEA tOEP OE tCAC tAA tOEZ tRAC tOHO Dout t uc tDZO Dout High-Z tCLZ Data Sheet E0177H10 15 HM5113165FTD-6 RAS-Only Refresh Cycle tRC tRAS tRP EO RAS tT tRPC tCRP tCRP CAS L tASR Address tRAH Row tOFR High-Z od Data Sheet E0177H10 16 t uc ; Dout Pr tOFF HM5113165FTD-6 CAS-Before-RAS Refresh Cycle tRC tRP tRC tRP EO tRAS tRAS tRP RAS tT tRPC tCP tRPC tCSR tCHR tCP tCRP tCSR tCHR L CAS tWRP tWRH tWRP tWRH WE Pr Address tOFR od tOFF High-Z t uc ; Dout Data Sheet E0177H10 17 HM5113165FTD-6 Hidden Refresh Cycle tRC tRAS tRP tRC tRAS tRC tRP tRAS tRP EO RAS tT tRSH tCHR tCRP tRCD CAS tRAL L tRAD tASR Address tRAH tASC Row tCAH Column Pr tRRH tRCS WE tWED od tDZC tRCH tCDD tRDD High-Z Din tDZO OE tCAC tAA tRAC t uc tOEA tOFF ; tCLZ tOH Dout Dout Data Sheet E0177H10 18 tOED tOFR tOHR tOEZ tWEZ tOHO HM5113165FTD-6 EDO Page Mode Read Cycle (1) t RP t HPC t RASP EO RAS tT t CSH t CP t HPC t CAS CAS t HPC t CPRH t CP t t CRP RSH t CAS t RCHR t RCS t CP tCAS tCAS t RCHC t RCH t RCS t RRH t RCH WE Address tRAH tASC tCAH L tASR Row Column 1 t WPE t ASC t CAH t ASC t CAH Column 2 Column 3 t CAL t CAL t RAL t CAH tASC t WED Column 4 t CAL t CAL tRDD tCDD tDZC Pr High-Z Din tCOL tDZO tCOP t OEP OE tCPA tOEA tOEZ tOHO tAA tOEZ ; tCAC tAA tOFR tOHR tOEZ tCPA tCPA tAA tCAC od tAA tCAC tOED tOEP tWEZ tRAC Dout tOEA tDOH Dout 1 Dout 2 Dout 2 tOHO Dout 3 tCAC tOHO tOFF tOH tOEA Dout 4 t uc Data Sheet E0177H10 19 HM5113165FTD-6 EDO Page Mode Read Cycle (2) t RP t RASP EO RAS tT t CSH t CP t HPC t CAS CAS tHPC t CP t HPC t CP t CAS t CAS t CRP tRSH tCAS t RCHC t RRH t RCH t RCS WE Address tRAH tASC tCAH L tASR Row Column 1 t ASC t CAH t ASC t CAH Column 2 t CAL t RAL t CAH tASC Column 3 t CAL t WED Column 4 t CAL tRDD t CAL tDZC tCDD Pr High-Z Din tCOL tDZO tCOP t OEP OE tOEA tCPA tOEZ tOFR tOHR tOEZ tCPA tAA ; tCAC tAA tCPA tAA tCAC od tAA tCAC tOED tOEP tDOH tRAC Dout tOHO tOEA tOEZ tDOH tOHO Dout 1 Dout 2 Dout 2 Dout 3 tCAC tOHO tOFF tOH tOEA Dout 4 t uc Data Sheet E0177H10 20 HM5113165FTD-6 EDO Page Mode Early Write Cycle tRP tRASP EO RAS tT tCSH tHPC tCAS tRCD tCP tRSH tCAS tCP tCAS tCRP CAS L tASR Address Row tRAH tASC Column 1 Column 2 tWCH tDH Din 1 tWCS tWCH tASC tCAH Column N tWCS tWCH tDS tDH Din 2 High-Z* tDS tDH Din N t uc Dout tCAH od tDS Din tASC Pr tWCS WE tCAH * t WCS t WCS (min) Data Sheet E0177H10 21 HM5113165FTD-6 EDO Page Mode Delayed Write Cycle*18 tRASP EO tRP RAS tT tCP tRCD tCRP tCP tCSH tHPC tCAS tCAS tRSH tCAS CAS L tRAD tASR tASC tCAH tASC tCAH Column 1 Column 2 tRAH Address Row tASC tCAH tWP tDZC tDS tRCS Din 1 tDZO tOED tDH Din 2 tDZO tOED tOEP tOEH tDZO tDH Din N tOED tOEP tOEH t uc ; tOEP tOEH tWP tDZC tDS od tWP tDZC tDS tDH Din tCWL tRWL tRCS tRCS WE tCWL Pr tCWL Column N OE tCLZ tCLZ tOEZ tCLZ tOEZ Dout Invalid Dout Invalid Dout Data Sheet E0177H10 22 tOEZ Invalid Dout High-Z HM5113165FTD-6 EDO Page Mode Read-Modify-Write Cycle*18 t RASP EO t RP RAS tT t HPRWC t CP t RCD t RSH t CP t CAS t CAS t CRP t CAS CAS L t ASR Address t RAD t ASC t RAH Row t ASC t CAH t CAH Column 1 Column 2 Column N Pr t RWD t CWL t AWD t RCS t CPW t AWD t CWD Din 1 t OED t OEP t OEH t RWL t CWD t WP t t DZC DS t DH Din 2 t OED t DZO t OEP t OEH t OED t DZO t OHO Din N t OEP t OEH t OHO ; ; t OHO t DH t uc OE t CWL t AWD t RCS t WP t t DZC DS t DH t DZO t CWL od t WP t t DZC DS Din t CPW t RCS t CWD WE t ASC t CAH t OEA t CAC t OEA t CAC t AA t OEA t CAC t AA t CPA t RAC t OEZ t CLZ t AA t CPA t OEZ t CLZ t OEZ t CLZ High-Z Dout Dout 1 Dout 2 Dout N Data Sheet E0177H10 23 HM5113165FTD-6 EDO Page Mode Mix Cycle (1) *20 t RP t RASP EO RAS tT t CAS CAS t CRP t CP t CP t CP t CAS tCAS t CSH tCAS tCWL tRSH t RCD t WCS tCPW tAWD WE L t ASC tRAH tASR Address Row tASC t CAH Column 2 Column 3 tASC t RAL t CAH Column 4 t CAL tRDD tCDD t CAL t DH Din 1 tWP t DH t DS High-Z Din 3 tOED ; Din Column 1 t ASC t CAH Pr t DS tCAH t RRH t RCH t RCS t RCS t WCH OE tCPA tAA tOEA tAA tCAC Dout tWED t DOH Dout 2 tOFR tWEZ tCPA od tCPA tOEP t OEZ tCAC t OHO Dout 3 tAA tOEZ tCAC tOHO tOEA tOFF tOH Dout 4 t uc Data Sheet E0177H10 24 HM5113165FTD-6 EDO Page Mode Mix Cycle (2)* 20 t RP t RASP RAS EO tT CAS t CSH t CAS t RCD t CAS tCAS t RCHR t RCS t RCH tWCS t WCH tCWL t ASC tRAH Row tCAH Column 1 t ASC t CAH t ASC t CAH Column 2 Column 3 tRSH t RCS t RRH t RCH tWP tCPW L Address tCAS t RCS WE tASR t CRP t CP t CP t CP t RAL t CAH tASC Column 4 t CAL t CAL t DS t DH Pr t DS High-Z Din Din 2 Din 3 t OEP t OEP tOED tOED tCOP tWED tCOL OE t OEA tOEA tCAC tOEZ tCPA tAA tCAC tRAC t OHO Dout 1 tOFR tWEZ tCPA od tAA Dout tRDD tCDD t DH tOEZ t OHO Dout 3 tAA tCAC tOEZ tOEA tOFF tOH tOHO Dout 4 t uc Data Sheet E0177H10 25 HM5113165FTD-6 Package Dimensions HM5113165FTD Series (TTP-50DE) Unit: mm 20.95 21.35 Max 26 10.16 50 L 0.80 *0.30 ± 0.10 0.28 ± 0.05 25 0.13 M *0.12 ± 0.05 0.10 ± 0.04 Pr 1.20 Max 0.80 11.76 ± 0.20 1.075 Max 0.10 0.50 ± 0.10 Hitachi Code JEDEC EIAJ Mass (reference value) TTP-50DE — — 0.56 g od *Dimension including the plating thickness Base material dimension 0° – 5° 0.45 1 0.05 ± 0.05 EO As of January, 2001 t uc Data Sheet E0177H10 26 HM5113165FTD-6 Cautions L EO 1. Elpida Memory, Inc. neither warrants nor grants licenses of any rights of Elpida Memory, Inc.’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Elpida Memory, Inc. bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document. 2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use. 3. Elpida Memory, Inc. makes every attempt to ensure that its products are of high quality and reliability. However, contact Elpida Memory, Inc. before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support. 4. Design your application so that the product is used within the ranges guaranteed by Elpida Memory, Inc. particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Elpida Memory, Inc. bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail-safes, so that the equipment incorporating Elpida Memory, Inc. product does not cause bodily injury, fire or other consequential damage due to operation of the Elpida Memory, Inc. product. 5. This product is not designed to be radiation resistant. 6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Elpida Memory, Inc.. 7. Contact Elpida Memory, Inc. for any questions regarding this document or Elpida Memory, Inc. semiconductor products. od Pr C Elpida Memory, Inc. 2001 t uc Data Sheet E0177H10 27