SIL15C Series 5 Vin and 12 Vin single output DC-DC CONVERTERS • • • • • • • • C Class Non-isolated 1 NEW Product 15 A current rating Input voltage range: 4.5 Vdc to 5.5 Vdc or 10.2 Vdc to 13.8 Vdc Output voltage range: 0.9 Vdc - 5.0 Vdc Industry leading value • Cost optimised design Excellent transient response Output Voltage adjustability • Pathway for future upgrades • Supports silicon voltage migration • Resulting in reduced design-in and qualification time Designed in reliability: MTBF of >7 million hrs per Telcordia SR-332 Available RoHS compliant The SIL15C Series is a new high density open frame non-isolated converter for spacesensitive applications. Each model has a wide input range (4.5 Vdc to 5.5 Vdc or 10.2 Vdc to 13.8 Vdc) and offer a wide 0.9 Vdc to 3.3 Vdc/5 Vdc output voltage range with a 15 A load. An external resistor adjusts the output voltage from its pre-set value of 0.9 Vdc to any value up to the maximum allowed value for that model. Typical efficiencies are 89% for the 5 V input version and 91% for the 12 V input version. The SIL15C series offers remote ON/OFF and overcurrent protection as standard. With full international safety approval including EN60950 and UL/cUL60950, the SIL15C reduces compliance costs and time to market. 2 YEAR WARRANTY SPECIFICATIONS All specifications are typical at nominal input, full load at 25 °C unless otherwise stated OUTPUT SPECIFICATIONS Voltage adjustability (See Note 5) INPUT SPECIFICATIONS (CONTD.) 5 V input models 12 V input models 0.9-3.3 Vdc 0.9V-5.0 Vdc Output setpoint accuracy With 1.0% trim resistors ±2.5% Line regulation Low line to high line ±0.2% max. Load regulation Full load to min. load ±0.5% max. Min/max load Overshoot (at turn on) 5 V input models 12 V input models Undershoot (See Note 1) Transient response (See Note 2) Deviation 5 Vin 12 Vin 4.5 Vdc 9.0 Vdc Turn OFF threshold 5 Vin 12 Vin 4.3 Vdc 7.5 Vdc GENERAL SPECIFICATIONS 0 A/15 A Efficiency 3% max. 1% max. Switching frequency Fixed Approvals and standards (pending) (See Note 4) 100 mV max. Ripple and noise 5 Hz to 20 MHz Turn ON threshold See table See Table 200 kHz TÜV Product Services IEC60950, UL/cUL60950 Material flammability UL94V-0 Weight 100 mV 200 µs recovery to within regulation band 14.2 g (0.5 oz) MTBF Telcordia SR-332 7,817,294 hours ENVIRONMENTAL SPECIFICATIONS INPUT SPECIFICATIONS Input voltage range 5 V input model 12 V input model Input current Minimum load Remote OFF Input current (max.) (See Note 3) 5 V input model 12 V input model 11.5 A @ Io max. 8.1 A @ Io max. Input reflected ripple (See Note 4) 5 V input model 12 V input model 200 mA (pk-pk) 200 mA (pk-pk) Remote ON/OFF Logic compatibility ON OFF Start-up time (See Note 9) 4.5-5.5 Vdc 10.2-13.8 Vdc 65 mA 20 mA Active high >2.4 Vdc <0.8 Vdc Power up Remote ON/OFF <20 ms <20 ms Thermal performance (See Note 8) Operating ambient, temperature Non-operating 0 ºC to +80 ºC -40 ºC to +125 ºC PROTECTION Short-circuit protection Hiccup, non-latching RECOMMENDED SYSTEM CAPACITANCE Input capacitance Output capacitance (See Note 11) (See Note 11) 270 µF/20 mΩ esr max. 680 µF/10 mΩ esr max. International Safety Standard Approvals UL/cUL CAN/CSA 22.2 No. E139421 UL 60950 file No. E139421 TÜV Product Service (EN60950) Certificate No. B 04 08 19870 228 CB report and certificate to US/6415C/UL File Name: sil15c.pdf Rev (05): 13 Dec 2005 SIL15C Series 5 Vin and 12 Vin single output DC-DC CONVERTERS C Class Non-isolated 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm OUTPUT POWER (MAX.) INPUT VOLTAGE OVP OUTPUT OUTPUT CURRENT VOLTAGE (12) (MIN.) 50 W 4.5-5.5 Vdc N/A 0.9-3.3 Vdc 75 W 10.2-13.8 Vdc N/A 0.9-5.0 Vdc Part Number System with Options NEW Product OUTPUT CURRENT (MAX.) EFFICIENCY (TYP.) LINE LOAD MODEL NUMBER (8,13,14,15) 0A 15 A 89% ±0.2% ±0.5% SIL15C-05SADJ-VJ 0A 15 A 91% ±0.2% ±0.5% SIL15C-12SADJ-VJ REGULATION SIL15C-12SADJ-VJ Packaging Options (15) J = Pb-free (RoHS 6/6 compliant) Product Family SIL = Single in Line Mounting Option V = Vertical Mount H = Horizontal Mount Rated Output Current 15 = 15 Amps Performance C = Cost Optimised Number of Outputs SADJ = Single Adjustable Output Input Voltage 05 = 4.5 Vdc to 5.5 Vdc 12 = 10.2 Vdc to 13.8 Vdc Output Voltage Adjustment of the SIL15C Series The ultra-wide output voltage trim range offers major advantages to users who select the SIL15C series. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.9 Vdc to 5.0 Vdc. When the SIL15C series converter leaves the factory the output has been adjusted to the default voltage of 0.9 V Notes 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Measured as per recommended set-up. Cin = 270 µF (20 mΩ esr max, Cout = 680 µF (10 mΩ esr max). di/dt = 10 A/µs, Vin = Nom, Tc = 25 °C, load change = 0.50 lo max. to 0.75 lo max. and 0.75 lo max. to 0.50 lo max. External input fusing is recommended. Measured with external filter. See Application Note 131 for details. Uses external resistor from trim pin to output ground. Min value = 485 Ω for 5 V model, 280 Ω for 12 V model. See Application Note 131 for details. Signal line assumed <3 m in length This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. The standard unit with the suffix '-V' is for vertical mounting. To order a unit with horizontal mounting, please add the suffix '-H' to the model number, e.g. SIL15C-05SADJ-HJ. Power-up is the time from application of dc input to Power Good enabled. Remote ON/OFF is from ON/OFF asserted high to power good enabled. See Application Note 131 for operation above 50 ºC. See Application Note 131 for ripple current requirements. These models have a wide trim output. 5 Vin has an output of 0.9 Vdc to 3.3 Vdc and 12 Vin has an output of 0.9 Vdc to 5 Vdc. An external resistor adjusts the output voltage. To order a unit with a pin length of 0.150”, please add suffix ‘P4’ to the model number, e.g. SIL15C-05SADJ-HP4J. TSE RoHS 5/6 (non Pb-free) compliant versions may be available on special request, please contact your local sales representative for details. NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/powergroup/products.htm to find a suitable alternative. Ripple and Noise Specification Output Voltage Pk - Pk RMS 5 V input models 0.9-2.5 Vdc 3.3 Vdc 30 mV 40 mV 15 mV 15 mV 12 V input models 0.9-2.5 Vdc 3.3-5 Vdc 50 mV 50 mV 20 mV 20 mV Model File Name: sil15c.pdf Rev (05): 13 Dec 2005 SIL15C Series 5 Vin and 12 Vin single output DC-DC CONVERTERS C Class Non-isolated 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product 0.475 ±0.025 (12.08 ±0.64) Pin 11 PIN CONNECTIONS Vout 2 Vout 3 Vout 4 Trim 5 Remote ON/OFF 6 Power Good 7 Ground 8 Ground 9 Reserved 10 Vin 11 Vin 12 Mechanical support (horizontal version only) 13 Mechanical support (horizontal version only) 1.000 (25.40) 2 places 0.64 ±0.025 (0.025) typ. ±0.001 1.100 (27.94) 0.050 (1.27) 2 places 0.150 (3.81) 0.150 (3.81) Ref 0.100 (2.54) 9 places 1.050 (26.67) All dimensions in inches (mm) General tolerance ±0.01in (±0.25mm) except where specified otherwise Figure 1: Mechanical Drawing - Horizontal Mount Version 0.075 (1.91) 1.200 (30.48) Pin 11 0.025 ±0.001 (0.64) Typ ±0.025 0.40 ±0.025 (10.186 ±0.635) 0.26 ±0.015 (6.704 ±0.381) 0.062 (1.57) Ref 1.10 (27.940) 1 0.120 (3.05) 13 places Pin 1 0.050 (1.27) Ref FUNCTION 0.260 ±0.015 (6.70 ±0.40) Pin 1 0.025 ±0.001 (0.64) Typ. ±0.025 0.140 (3.56) 11 Places PIN NUMBER 1.100 (27.94) Mechanical Support Pin 2 places 0.062 (1.57) Ref 0.050 (1.27) Ref 1.200 (30.48) 0.050 (1.27) Typ 0.050 (1.27) 0.025 ±0.001 (0.64) Typ. ±0.025 0.100 (2.54) 9 Places 1.050 (26.67) 0.150 (3.81) All dimensions in inches (mm) General tolerance ±0.01in (±0.25mm) except where specified otherwise Figure 2: Mechanical Drawing - Vertical Mount Version Datasheet © Artesyn Technologies® 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: Application Note Longform Datasheet www.artesyn.com File Name: sil15c.pdf Rev (05): 13 Dec 2005