TI TLV2731IDBVTG4

TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
D
D
D
D
D
D
D
D
D
DBV PACKAGE
(TOP VIEW)
Output Swing Includes Both Supply Rails
Low Noise . . . 15 nV/√Hz Typ at f = 1 kHz
Low Input Bias Current . . . 1 pA Typ
Fully Specified for Single-Supply 3-V and
5-V Operation
Common-Mode Input Voltage Range
Includes Negative Rail
High Gain Bandwidth . . . 2 MHz at
VDD = 5 V with 600 Ω Load
High Slew Rate . . . 1.6 V/µs at VDD = 5 V
Wide Supply Voltage Range
2.7 V to 10 V
Macromodel Included
OUT
1
VDD+
2
IN +
3
5
VDD– /GND
4
IN–
description
The TLV2731 is a single low-voltage operational amplifier available in the SOT-23 package. It offers 2 MHz of
bandwidth and 1.6 V/µs of slew rate for applications requiring good ac performance. The device exhibits
rail-to-rail output performance for increased dynamic range in single or split supply applications. The TLV2731
is fully characterized at 3 V and 5 V and is optimized for low-voltage applications.
The TLV2731, exhibiting high input impedance and low noise, is excellent for small-signal conditioning of
high-impedance sources, such as piezoelectric transducers. Because of the micropower dissipation levels
combined with 3-V operation, these devices work well in hand-held monitoring and remote-sensing
applications. In addition, the rail-to-rail output feature with single- or split-supplies makes this family a great
choice when interfacing with analog-to-digital converters (ADCs). The device can also drive 600-Ω loads for
telecom applications.
With a total area of 5.6mm2, the SOT-23 package only requires one-third the board space of the standard 8-pin
SOIC package. This ultra-small package allows designers to place single amplifiers very close to the signal
source, minimizing noise pick-up from long PCB traces.
AVAILABLE OPTIONS
PACKAGED DEVICES
TA
VIOmax AT 25°C
0°C to 70°C
3 mV
TLV2731CDBV
VALC
– 40°C to 85°C
3 mV
TLV2731IDBV
VALI
SOT-23 (DBV)†
SYMBOL
CHIP
FORM‡
(Y)
TLV2731Y
† The DBV package available in tape and reel only.
‡ Chip forms are tested at TA = 25°C only.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Advanced LinCMOS is a trademark of Texas Instruments.
Copyright  2001, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TLV2731Y chip information
This chip, when properly assembled, displays characteristics similar to the TLV2731C. Thermal compression
or ultrasonic bonding may be used on the doped-aluminum bonding pads. This chip may be mounted with
conductive epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
(5)
VDD +
(2)
(1)
(3)
+
IN +
(4)
(1)
OUT
–
IN –
(5)
VDD – / GND
CHIP THICKNESS: 10 MILS TYPICAL
BONDING PADS: 4 × 4 MILS MINIMUM
46
(2)
TJmax = 150°C
TOLERANCES ARE ± 10%.
ALL DIMENSIONS ARE IN MILS.
PIN (2) IS INTERNALLY CONNECTED
TO BACKSIDE OF CHIP.
(4)
(3)
31
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
equivalent schematic
VDD +
Q3
Q6
Q9
R7
Q12
Q14
Q16
C2
IN +
R6
OUT
C1
IN –
R5
Q1
Q4
Q13
Q15
R2
Q2
Q5
R3
R4
Q7
Q8
Q10
Q17
D1
Q11
R1
VDD – / GND
COMPONENT COUNT†
Transistors
Diodes
Resistors
Capacitors
23
5
11
2
† Includes both amplifiers and all
ESD, bias, and trim circuitry
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 V
Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± VDD
Input voltage range, VI (any input, see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to VDD
Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 5 mA
Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA
Total current into VDD + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA
Total current out of VDD – . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA
Duration of short-circuit current (at or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: TLV2731C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
TLV2731I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: DBV package . . . . . . . . . . . . . . . . . . 260°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to VDD – .
2. Differential voltages are at the noninverting input with respect to the inverting input. Excessive current flows when input is brought
below VDD – – 0.3 V.
3. The output may be shorted to either supply. Temperature and /or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.
DISSIPATION RATING TABLE
PACKAGE
TA ≤ 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 85°C
POWER RATING
DBV
150 mW
1.2 mW/°C
96 mW
78 mW
recommended operating conditions
TLV2731C
Supply voltage, VDD (see Note 1)
Input voltage range, VI
Operating free-air temperature, TA
NOTE 1: All voltage values, except differential voltages, are with respect to VDD – .
4
MAX
MIN
MAX
2.7
10
2.7
10
VDD –
VDD –
Common-mode input voltage, VIC
POST OFFICE BOX 655303
TLV2731I
MIN
0
• DALLAS, TEXAS 75265
VDD + – 1.3
VDD + – 1.3
70
VDD –
VDD –
– 40
VDD + – 1.3
VDD + – 1.3
85
UNIT
V
V
V
°C
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature
coefficient of input
offset voltage
Input offset voltage
long-term drift
(see Note 4)
IIO
Input offset current
IIB
Input bias current
VICR
Common-mode input
voltage range
TA†
TEST CONDITIONS
Full range
VDD ± = ± 1.5 V,
V VIC = 0,
VO = 0,
RS = 50 Ω
VOL
AVD
Low-level
L
l
l output
t t
voltage
Large signal
Large-signal
differential voltage
amplification
0.7
3
µV/mo
25°C
0.5
60
0.5
150
1
0 to 2
60
–0 3
–0.3
22
to 2.2
60
150
1
150
60
150
0 to 2
0 to
1.7
1
7
pA
pA
–0 3
–0.3
22
to 2.2
0 to
1.7
17
2.87
25°C
Full range
RL = 600 Ω‡
VIC = 1.5
1 5 V,
V
VO = 1 V to 2 V
RL = 1 Mه
mV
0.003
25°C
IOL = 500 µA
3
V
IOH = – 1 mA
5V
VIC = 1
1.5
V,
0.7
UNIT
0.003
|VIO| ≤ 5 mV
IOL = 50 µA
MAX
25°C
25°C
VIC = 1.5 V,
TYP
µV/°C
Full range
IOH = – 2 mA
MIN
05
0.5
Full range
VOH
MAX
Full range
RS = 50 Ω
Ω,
TLV2731I
TYP
05
0.5
25°C
25
C
High-level
Hi
hl
l output
t t
voltage
TLV2731C
MIN
2.74
2.3
10
25°C
100
Full range
25°C
V
2.74
2.3
25°C
Full range
2.87
10
1
mV
100
300
1.6
300
1
0.3
1.6
0.3
V/mV
25°C
250
250
rid
Differential input
resistance
25°C
1012
1012
Ω
ric
Common-mode input
resistance
25°C
1012
1012
Ω
cic
Common-mode input
capacitance
f = 10 kHz
25°C
6
6
pF
zo
Closed-loop output
impedance
f = 1 MHz,
25°C
156
156
Ω
CMRR
Common-mode
rejection ratio
VIC = 0 to 1.7 V,,
VO = 1.5 V,
RS = 50 Ω
kSVR
Supply voltage
rejection ratio
(∆VDD /∆VIO)
VDD = 2.7 V to 8 V,,
VIC = VDD /2,
No load
IDD
Supply current
VO = 1
1.5
5V
V,
AV = 1
No load
25°C
60
Full range
55
25°C
70
Full range
70
70
60
70
dB
55
96
70
96
dB
25°C
Full range
70
750
1200
1500
750
1200
1500
µA
† Full range for the TLV2731C is 0°C to 70°C. Full range for the TLV2731I is – 40°C to 85°C.
‡ Referenced to 1.5 V
NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
operating characteristics at specified free-air temperature, VDD = 3 V
PARAMETER
TA†
TEST CONDITIONS
TLV2731C
MIN
TYP
25°C
0.75
1.25
Full
range
0.5
TLV2731I
MAX
MIN
TYP
0.75
1.25
SR
Slew rate at unity
gain
VO = 1.1 V to 1.9 V,
CL = 100 pF‡
Vn
Equivalent
input
q
noise voltage
f = 10 Hz
25°C
105
105
f = 1 kHz
25°C
16
16
Peak-to-peak
equivalent input
noise voltage
f = 0.1 Hz to 1 Hz
25°C
1.4
1.4
VN(PP)
f = 0.1 Hz to 10 Hz
25°C
1.5
1.5
In
Equivalent input
noise current
25°C
0.6
0.6
RL = 600 Ω‡,
VO = 1 V to 2 V,
f = 20 kHz,
kHz
RL = 600 Ω‡
AV = 1
MAX
UNIT
V/µs
0.5
nV/√Hz
µV
fA /√Hz
0.285%
0.285%
AV = 10
7.2%
7.2%
VO = 1 V to 2 V,
f = 20 kHz,
RL = 600 Ω§
AV = 1
AV = 10
0.014%
0.014%
0.098%
0.098%
0.13%
0.13%
Gain-bandwidth
product
f = 10 kHz,
CL = 100 pF‡
RL = 600 Ω‡,
25°C
1.9
1.9
MHz
BOM
Maximum outputswing bandwidth
VO(PP) = 1 V,
RL = 600 Ω‡,
AV = 1,
CL = 100 pF‡
25°C
60
60
kHz
0.9
0.9
Settling time
AV = –1,
Step = 1 V to 2 V,,
RL = 600 Ω‡,
CL = 100 pF‡
To 0.1%
ts
1.5
1.5
RL = 600 Ω‡,
CL = 100 pF‡
25°C
50°
50°
25°C
8
8
THD+N
φm
Total harmonic
distortion plus
noise
Phase margin at
unity gain
25°C
AV = 100
µs
25°C
To 0.01%
Gain margin
† Full range is – 40°C to 85°C.
‡ Referenced to 1.5 V
§ Referenced to 0 V
6
25°C
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
dB
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature
coefficient of input
offset voltage
Input offset voltage
long-term drift
(see Note 4)
IIO
Input offset current
IIB
Input bias current
VICR
Common-mode input
voltage range
TA†
TEST CONDITIONS
Full range
VDD ± = ± 2.5 V
V,
VO = 0,
VIC = 0,
RS = 50 Ω
VOL
AVD
Low-level
L
l
l output
t t
voltage
Large signal
Large-signal
differential voltage
amplification
0.7
3
TYP
MAX
0.7
3
UNIT
mV
µV/°C
25°C
0.003
0.003
µV/mo
25°C
0.5
25°C
|VIO| ≤ 5 mV
60
0.5
150
1
Full range
60
1
150
0 to 4
–0 3
–0.3
42
to 4.2
60
150
60
150
0 to 4
pA
pA
–0 3
–0.3
42
to 4.2
V
IOH = – 1 mA
0 to
3.7
3
7
0 to
3.7
37
25°C
4.9
25°C
IOH = – 4 mA
MIN
05
0.5
Full range
VOH
MAX
Full range
RS = 50 Ω
Ω,
TLV2731I
TYP
05
0.5
25°C
25
C
High-level
Hi
hl
l output
t t
voltage
TLV2731C
MIN
Full range
4.9
4.6
4.3
VIC = 2.5 V,
IOL = 500 µA
5V
VIC = 2
2.5
V,
IOL = 1 mA
VIC = 2.5
2 5 V,
V
VO = 1 V to 4 V
RL = 600 Ω‡
Full range
RL = 1 Mه
25°C
400
400
25°C
80
25°C
160
Full range
25°C
V
4.6
4.3
80
1
mV
160
500
1.5
500
1
0.3
1.5
0.3
V/mV
rid
Differential input
resistance
25°C
1012
1012
Ω
ric
Common-mode input
resistance
25°C
1012
1012
Ω
cic
Common-mode input
capacitance
f = 10 kHz
25°C
6
6
pF
zo
Closed-loop output
impedance
f = 1 MHz,
25°C
138
138
Ω
CMRR
Common-mode
rejection ratio
VIC = 0 to 2.7 V,,
VO = 2.5 V,
RS = 50 Ω
kSVR
Supply voltage
rejection ratio
(∆VDD /∆VIO)
VDD = 4.4 V to 8 V,,
VIC = VDD /2,
No load
IDD
Supply current
VO = 2
2.5
5V
V,
AV = 1
No load
25°C
60
Full range
55
25°C
70
Full range
70
70
60
70
dB
55
96
70
96
dB
25°C
Full range
70
850
1300
1600
850
1300
1600
µA
† Full range for the TLV2731C is 0°C to 70°C. Full range for the TLV2731I is – 40°C to 85°C.
‡ Referenced to 2.5 V
NOTE 5: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated
to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
7
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
operating characteristics at specified free-air temperature, VDD = 5 V
PARAMETER
TA†
TEST CONDITIONS
RL = 600 Ω‡,
TLV2731C
MIN
TYP
25°C
1
1.6
Full
range
0.7
TLV2731I
MAX
MIN
TYP
1
1.6
SR
Slew rate at unity
gain
VO = 1
1.5
5 V to 3
3.5
5V
V,
CL = 100 pF‡
Vn
Equivalent
input
q
noise voltage
f = 10 Hz
25°C
100
100
f = 1 kHz
25°C
15
15
Peak-to-peak
equivalent input
noise voltage
f = 0.1 Hz to 1 Hz
25°C
1.4
1.4
VN(PP)
f = 0.1 Hz to 10 Hz
25°C
1.5
1.5
In
Equivalent input
noise current
25°C
0.6
0.6
THD+N
BOM
ts
φm
VO = 1.5 V to 3.5 V,
f = 20 kHz,
kHz
RL = 600 Ω‡
AV = 1
0.409%
AV = 10
3.68%
3.68%
VO = 1.5 V to 3.5 V,
f = 20 kHz,
RL = 600 Ω§
AV = 1
AV = 10
0.018%
0.018%
0.045%
0.045%
0.116%
0.116%
Gain-bandwidth
product
f = 10 kHz,
CL = 100 pF‡
RL = 600 Ω‡,
Maximum
output-swing
bandwidth
VO(PP) = 1 V,
RL = 600 Ω‡,
AV = 1,
CL = 100 pF‡
To 0.1%
Settling time
AV = –1,
Step = 1.5 V to 3.5 V,,
RL = 600 Ω‡,
CL = 100 pF‡
RL = 600 Ω‡,
CL = 100 pF‡
Phase margin at
unity gain
8
25°C
µV
fA /√Hz
25°C
2
2
MHz
25°C
300
300
kHz
0.95
0.95
2.4
2.4
25°C
48°
48°
25°C
8
8
µs
25°C
To 0.01%
POST OFFICE BOX 655303
nV/√Hz
25°C
AV = 100
Gain margin
† Full range is – 40°C to 85°C.
‡ Referenced to 2.5 V
§ Referenced to 0 V
UNIT
V/µs
0.7
0.409%
Total harmonic
distortion plus
noise
MAX
• DALLAS, TEXAS 75265
dB
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
electrical characteristics at VDD = 3 V, TA = 25°C (unless otherwise noted)
PARAMETER
VIO
IIO
Input offset voltage
IIB
Input bias current
VICR
TLV2731Y
TEST CONDITIONS
MIN
TYP
MAX
UNIT
µV
750
VDD ± = ± 1.5
1 5 V,
V
RS = 50 Ω
VIC = 0,
0
Common-mode input voltage
g range
g
|VIO| ≤ 5 mV,
RS = 50 Ω
VOH
High-level output voltage
VOL
Low level output voltage
Low-level
IOH = – 1 mA
VIC = 1.5 V,
AVD
Large signal differential voltage amplification
Large-signal
rid
Differential input resistance
ric
Common-mode input resistance
cic
Common-mode input capacitance
f = 10 kHz
zo
Closed-loop output impedance
f = 1 MHz,
Ω
Common-mode rejection ratio
VIC = 0 to 1.7 V,
AV = 1
VO = 0,
156
CMRR
RS = 50 Ω
70
dB
kSVR
Supply voltage rejection ratio (∆VDD /∆VIO)
VDD = 2
2.7
7 V to 8 V
V,
VIC = 0
0,
No load
96
dB
VO = 0,
No load
750
µA
Input offset current
VIC = 1.5 V,
IDD
Supply current
† Referenced to 1.5 V
VO = 1 V to 2 V
VO = 0,
0
IOL = 50 µA
IOL = 500 µA
0.5
60
pA
1
60
pA
– 0.3
to
2.2
V
2.87
V
10
mV
100
RL = 600 Ω†
1.6
RL = 1 Mن
250
V/mV
1012
1012
Ω
6
pF
Ω
electrical characteristics at VDD = 5 V, TA = 25°C (unless otherwise noted)
PARAMETER
VIO
IIO
Input offset voltage
IIB
Input bias current
VICR
VIC = 0,
0
Common-mode input voltage
g range
g
|VIO| ≤ 5 mV,
RS = 50 Ω
VOH
High-level output voltage
VOL
Low level output voltage
Low-level
IOH = – 1 mA
VIC = 2.5 V,
AVD
Large signal differential voltage amplification
Large-signal
rid
Differential input resistance
ric
Common-mode input resistance
cic
Common-mode input capacitance
f = 10 kHz
zo
Closed-loop output impedance
f = 1 MHz,
CMRR
Common-mode rejection ratio
kSVR
Supply voltage rejection ratio (∆VDD /∆VIO)
VIC = 2.5 V,
VO = 1 V to 2 V
VO = 0,
0
IOL = 500 µA
IOL = 1 mA
TYP
MAX
µV
60
pA
1
60
pA
– 0.3
to
4.2
V
4.9
V
80
160
15
RL = 1 Mن
400
VIC = 0 to 1.7 V,
VDD = 2
2.7
7 V to 8 V
V,
VIC = 0
0,
VO = 0,
No load
• DALLAS, TEXAS 75265
UNIT
0.5
RL = 600 Ω†
AV = 1
VO = 0,
POST OFFICE BOX 655303
MIN
710
VDD ± = ± 1.5
1 5 V,
V
RS = 50 Ω
Input offset current
IDD
Supply current
† Referenced to 2.5 V
TLV2731Y
TEST CONDITIONS
mV
V/mV
1012
1012
Ω
6
pF
Ω
138
Ω
RS = 50 Ω
70
dB
No load
96
dB
850
µA
9
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
Input offset voltage
Distribution
vs Common-mode input voltage
1,, 2
3, 4
αVIO
IIB/IIO
Input offset voltage temperature coefficient
Distribution
5, 6
Input bias and input offset currents
vs Free-air temperature
7
VI
Input voltage
vs Supplyy voltage
g
vs Free-air temperature
8
9
VOH
VOL
High-level output voltage
vs High-level output current
10, 13
Low-level output voltage
vs Low-level output current
11, 12, 14
VO(PP)
Maximum peak-to-peak output voltage
vs Frequency
15
IOS
Short circuit output current
Short-circuit
vs Supplyy voltage
g
vs Free-air temperature
16
17
VO
AVD
Output voltage
vs Differential input voltage
Differential voltage amplification
vs Load resistance
AVD
Large signal differential voltage amplification
Large-signal
vs Frequency
q
y
vs Free-air temperature
21,, 22
23, 24
zo
Output impedance
vs Frequency
25, 26
CMRR
Common mode rejection ratio
Common-mode
vs Frequency
q
y
vs Free-air temperature
27
28
kSVR
Supply voltage rejection ratio
Supply-voltage
vs Frequency
q
y
vs Free-air temperature
29,, 30
31
IDD
Supply current
vs Supply voltage
32
SR
Slew rate
vs Load capacitance
vs Free-air temperature
33
34
VO
VO
Inverting large-signal pulse response
35, 36
Voltage-follower large-signal pulse response
37, 38
VO
VO
Inverting small-signal pulse response
39, 40
Vn
Equivalent input noise voltage
vs Frequency
Noise voltage (referred to input)
Over a 10-second period
45
Total harmonic distortion plus noise
vs Frequency
46
Gain bandwidth product
Gain-bandwidth
vs Free-air temperature
vs Supply voltage
47
48
Gain margin
vs Load capacitance
49, 50
φm
Phase margin
vs Frequency
q
y
vs Load capacitance
21,, 22
51, 52
B1
Unity-gain bandwidth
vs Load capacitance
53, 54
THD + N
10
Voltage-follower small-signal pulse response
POST OFFICE BOX 655303
18, 19
20
41, 42
• DALLAS, TEXAS 75265
43, 44
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
DISTRIBUTION OF TLV2731
INPUT OFFSET VOLTAGE
DISTRIBUTION OF TLV2731
INPUT OFFSET VOLTAGE
20
16
537 Amplifiers From 1 Wafer Lot
VDD = ± 1.5 V
TA = 25°C
18
14
Precentage of Amplifiers – %
16
14
12
10
8
6
4
12
10
8
6
4
3
2.6
1.8
2.2
1
1.4
0.6
–0.2
0.2
–0.6
VIO – Input Offset Voltage – mV
VIO – Input Offset Voltage – mV
Figure 1
Figure 2
INPUT OFFSET VOLTAGE†
vs
COMMON-MODE INPUT VOLTAGE
INPUT OFFSET VOLTAGE†
vs
COMMON-MODE INPUT VOLTAGE
1
1
VDD = 3 V
RS = 50 Ω
TA = 25°C
0.8
0.8
VIO – Input Offset Voltage – mV
0.6
VIO – Input Offset Voltage – mV
–1.4
–1
–1.8
3
2.6
1.8
2.2
1
1.4
–0.2
0.2
0.6
–0.6
–1.4
–1
–1.8
–3
–2.6
–2.2
–2.2
0
0
–3
2
2
–2.6
Precentage of Amplifiers – %
537 Amplifiers
From 1 Wafer Lot
VDD = ± 2.5 V
TA = 25°C
0.4
0.2
0
– 0.2
VDD = 5 V
RS = 50 Ω
TA = 25°C
0.6
0.4
0.2
0
– 0.2
ÁÁ
ÁÁ
ÁÁ
– 0.4
ÁÁ
ÁÁ
– 0.6
– 0.8
– 0.4
– 0.6
– 0.8
–1
–1
0
1
2
3
VIC – Common-Mode Input Voltage – V
–1
–1
0
1
2
3
4
VIC – Common-Mode Input Voltage – V
Figure 3
5
Figure 4
† For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
DISTRIBUTION OF TLV2731 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT†
DISTRIBUTION OF TLV2731 INPUT OFFSET
VOLTAGE TEMPERATURE COEFFICIENT†
30
30
32 Amplifiers From
1 Wafer Lots
VDD± = ± 2.5 V
P Package
TA = 25°C to 125°C
25
Percentage of Amplifiers – %
Percentage of Amplifiers – %
25
32 Amplifiers From
1 Wafer Lots
VDD± = ± 1.5 V
P Package
TA = 25°C to 125°C
20
15
10
20
15
10
5
5
0
0
–4
–3
–2
–1
0
1
2
3
α VIO – Input Offset Voltage
Temperature Coefficient – µV/°C
4
–4
–3
–2
–1
0
1
2
α VIO – Input Offset Voltage
Temperature Coefficient – µV/°C
INPUT BIAS AND INPUT OFFSET CURRENTS†
vs
FREE-AIR TEMPERATURE
100
90
80
INPUT VOLTAGE
vs
SUPPLY VOLTAGE
5
VDD± = ± 2.5 V
VIC = 0
VO = 0
RS = 50 Ω
RS = 50 Ω
TA = 25°C
4
3
70
60
50
40
2
1
0
|VIO| ≤ 5 mV
–1
ÁÁ
ÁÁ
30
–2
–3
20
IIB
IIO
–4
10
0
25
–5
45
65
85
105
TA – Free-Air Temperature – °C
125
1
Figure 7
1.5
2
2.5
3
3.5
|VDD ±| – Supply Voltage – V
Figure 8
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
12
4
Figure 6
VI – Input Voltage – V
IIIB
IB and IIIO
IO – Input Bias and Input Offset Currents – pA
Figure 5
3
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
4
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
INPUT VOLTAGE†
vs
FREE-AIR TEMPERATURE
HIGH-LEVEL OUTPUT VOLTAGE†‡
vs
HIGH-LEVEL OUTPUT CURRENT
3
5
VDD = 3 V
VDD = 5 V
VOH – High-Level Output Voltage – V
4
VI – Input Voltage – V
3
|VIO| ≤ 5 mV
2
ÁÁ
1
ÁÁ
ÁÁ
0
–1
– 55 – 35 – 15
5
25
45
65 85 105
TA – Free-Air Temperature – °C
2.5
TA = – 40°C
2
TA = 25°C
1.5
TA = 85°C
1
TA = 125°C
0.5
0
5
0
125
Figure 9
LOW-LEVEL OUTPUT VOLTAGE†‡
vs
LOW-LEVEL OUTPUT CURRENT
1.2
1.4
1
VOL – Low-Level Output Voltage – V
VOL – Low-Level Output Voltage – V
VDD = 3 V
TA = 25°C
VIC = 0
0.8
VIC = 0.75 V
0.6
VIC = 1.5 V
ÁÁ
ÁÁ
ÁÁ
0.4
0.2
0
0
4
2
3
IOL – Low-Level Output Current – mA
1
15
Figure 10
LOW-LEVEL OUTPUT VOLTAGE‡
vs
LOW-LEVEL OUTPUT CURRENT
ÁÁ
ÁÁ
10
|IOH| – High-Level Output Current – mA
5
VDD = 3 V
VIC = 1.5 V
1.2
TA = 125°C
1
TA = 85°C
0.8
TA = 25°C
0.6
TA = – 40°C
0.4
0.2
0
0
1
2
3
4
IOL – Low-Level Output Current – mA
Figure 11
5
Figure 12
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
‡ For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
LOW-LEVEL OUTPUT VOLTAGE†‡
vs
LOW-LEVEL OUTPUT CURRENT
HIGH-LEVEL OUTPUT VOLTAGE†‡
vs
HIGH-LEVEL OUTPUT CURRENT
5
1.4
VDD = 5 V
VIC = 2.5 V
VDD = 5 V
ÁÁ
ÁÁ
1.2
4
TA = – 40°C
VOL – Low-Level Output Voltage – V
VOH – High-Level Output Voltage – V
4.5
3.5
3
TA = 25°C
2.5
TA = 85°C
2
1.5
1
0.5
0
5
10
1
TA = 85°C
0.8
TA = 25°C
0.6
15
20
25
TA = – 40°C
0.4
ÁÁ
ÁÁ
TA = 125°C
0
TA = 125°C
0.2
0
4
5
1
2
3
IOL – Low-Level Output Current – mA
0
30
|IOH| – High-Level Output Current – mA
Figure 13
Figure 14
ÁÁ
ÁÁ
ÁÁ
30
RI = 600 Ω
TA = 25°C
4
VDD = 5 V
3
VDD = 3 V
2
1
0
10 2
10 3
SHORT-CIRCUIT OUTPUT CURRENT
vs
SUPPLY VOLTAGE
I OS – Short-Circuit Output Current – mA
VO(PP) – Maximum Peak-to-Peak Output Voltage – V
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE‡
vs
FREQUENCY
5
10 4
10 5
f – Frequency – Hz
10 6
VO = VDD/2
VIC = VDD/2
TA = 25°C
25
20
15
VID = – 100 mV
10
5
0
–5
– 10
– 15
VID = 100 mV
– 20
– 25
– 30
2
Figure 15
3
4
5
6
VDD – Supply Voltage – V
7
Figure 16
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
‡ For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
14
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
8
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
SHORT-CIRCUIT OUTPUT CURRENT †‡
vs
FREE-AIR TEMPERATURE
3
30
VDD = 5 V
VIC = 2.5 V
VO = 2.5 V
25
20
15
VID = – 100 mV
10
5
0
–5
– 10
VID = 100 mV
– 15
VDD = 3 V
VIC = 1.5 V
RI = 600 Ω
TA = 25°C
2.5
V O – Output Voltage – V
I OS – Short-Circuit Output Current – mA
OUTPUT VOLTAGE‡
vs
DIFFERENTIAL INPUT VOLTAGE
2
1.5
1
0.5
– 20
– 25
– 30
– 75
0
– 50
– 25
0
25
50
75
100
TA – Free-Air Temperature – °C
125
– 10 – 8
–6
–4
4
6
8
10
DIFFERENTIAL VOLTAGE AMPLIFICATION‡
vs
LOAD RESISTANCE
AVD – Differential Voltage Amplification – V/mV
5
V O – Output Voltage – V
2
Figure 18
OUTPUT VOLTAGE‡
vs
DIFFERENTIAL INPUT VOLTAGE
VDD = 5 V
VIC = 2.5 V
RL = 600 Ω
TA = 25°C
3
2
1
0
– 10 – 8
0
VID – Differential Input Voltage – mV
Figure 17
4
–2
–6 –4 –2
0
2
4
6
VID – Differential Input Voltage – mV
8
10
10 4
VO(PP) = 2 V
TA = 25°C
10 3
VDD = 5 V
VDD = 3 V
10 2
101
ÁÁ
ÁÁ
ÁÁ
1
0.1
Figure 19
1
101
10 2
10 3
RL – Load Resistance – kΩ
Figure 20
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
‡ For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE MARGIN†
vs
FREQUENCY
ÁÁ
ÁÁ
60
180°
VDD = 3 V
RL = 600 Ω
CL= 100 pF
TA = 25°C
135°
40
90°
Phase Margin
45°
20
Gain
0°
0
φom
m – Phase Margin
AVD
A
VD – Large-Signal Differential
Voltage Amplification – dB
80
– 45°
– 20
– 40
10 4
10 5
10 6
f – Frequency – Hz
– 90°
10 7
Figure 21
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE MARGIN†
vs
FREQUENCY
ÁÁ
ÁÁ
60
180°
VDD = 5 V
RL= 600 Ω
CL= 100 pF
TA = 25°C
135°
40
Phase Margin
90°
45°
20
Gain
0
0°
– 45°
– 20
– 40
10 4
φom
m – Phase Margin
AVD
A
VD – Large-Signal Differential
Voltage Amplification – dB
80
10 5
10 6
f – Frequency – Hz
– 90°
10 7
Figure 22
† For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION†‡
vs
FREE-AIR TEMPERATURE
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION†‡
vs
FREE-AIR TEMPERATURE
10 3
10 3
AVD – Large-Signal Differential Voltage
Amplification – V/mV
AVD – Large-Signal Differential Voltage
Amplification – V/mV
RL = 1 MΩ
10 2
101
RL = 600 Ω
1
VDD = 3 V
VIC = 1.5 V
VO = 0.5 V to 2.5 V
0.1
– 75
– 50
– 25
0
25
50
75
100
TA – Free-Air Temperature – °C
RL = 1 MΩ
10 2
101
RL = 600 Ω
1
VDD = 5 V
VIC = 2.5 V
VO = 1 V to 4 V
0.1
– 75
125
– 50
– 25
0
25
50
75
100
TA – Free-Air Temperature – °C
Figure 23
Figure 24
OUTPUT IMPEDANCE‡
vs
FREQUENCY
OUTPUT IMPEDANCE‡
vs
FREQUENCY
1000
1000
VDD = 5 V
TA = 25°C
100
z o – Output Impedance – Ω
z o – Output Impedance – Ω
VDD = 3 V
TA = 25°C
AV = 100
10
AV = 10
1
100
10
1
AV = 1
0.1
10 2
125
AV = 100
AV = 10
AV = 1
10 3
10 4
f– Frequency – Hz
10 5
10 6
0.1
10 2
Figure 25
10 3
10 4
f– Frequency – Hz
10 5
10 6
Figure 26
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
‡ For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
COMMON-MODE REJECTION RATIO†‡
vs
FREE-AIR TEMPERATURE
COMMON-MODE REJECTION RATIO†
vs
FREQUENCY
84
TA = 25°C
VDD = 5 V
VIC = 2.5 V
CMMR – Common-Mode Rejection Ratio – dB
CMRR – Common-Mode Rejection Ratio – dB
100
80
60
VDD = 3 V
VIC = 1.5 V
40
20
0
10 2
10 3
10 4
10 5
f – Frequency – Hz
10 6
82
VDD = 5 V
80
78
76
74
72
VDD = 3 V
70
– 75 – 50 – 25
0
25
50
75 100
TA – Free-Air Temperature – °C
10 7
Figure 27
Figure 28
SUPPLY-VOLTAGE REJECTION RATIO†
vs
FREQUENCY
SUPPLY-VOLTAGE REJECTION RATIO†
vs
FREQUENCY
Á
Á
Á
100
VDD = 3 V
TA = 25°C
k SVR – Supply-Voltage Rejection Ratio – dB
k SVR – Supply-Voltage Rejection Ratio – dB
100
80
kSVR +
60
40
kSVR –
20
0
10 2
10 3
10 4
10 5
f – Frequency – Hz
10 6
10 7
ÁÁ
ÁÁ
ÁÁ
VDD = 5 V
TA = 25°C
80
kSVR +
60
kSVR –
40
20
0
10 2
10 3
10 4
10 5
10 6
f – Frequency – Hz
Figure 29
Figure 30
† For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
‡ Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
18
125
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
10 7
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
SUPPLY-VOLTAGE REJECTION RATIO†
vs
FREE-AIR TEMPERATURE
SUPPLY CURRENT†
vs
SUPPLY VOLTAGE
1000
VO = 0
No Load
VDD = 2.7 V to 8 V
VIC = VO = VDD / 2
TA = – 40°C
98
I DD – Supply Current – µ A
k SVR – Supply-Voltage Rejection Ratio – dB
100
96
92
90
– 75 – 50
TA = 85°C
TA = 25°C
500
ÁÁ
ÁÁ
ÁÁ
94
ÁÁ
ÁÁ
ÁÁ
750
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
250
0
0
125
1
2
3
7
8
SLEW RATE†‡
vs
FREE-AIR TEMPERATURE
3.5
4
VDD = 5 V
AV = – 1
TA = 25°C
SR –
VDD = 5 V
RL = 600 Ω
CL = 100 pF
AV = 1
3
2.5
SR – Slew Rate – V/ µ s
SR – Slew Rate – V/ µ s
6
Figure 32
SLEW RATE‡
vs
LOAD CAPACITANCE
3
5
VDD – Supply Voltage – V
Figure 31
SR +
4
2
1.5
1
SR –
2
SR +
1
0.5
0
101
10 2
10 3
10 4
10 5
0
– 75
– 50
CL – Load Capacitance – pF
Figure 33
– 25
0
25
50
75 100
TA – Free-Air Temperature – °C
125
Figure 34
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
‡ For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
INVERTING LARGE-SIGNAL PULSE
RESPONSE†
3
5
VDD = 3 V
RL = 600 Ω
CL = 100 pF
AV = –1
TA = 25°C
2
1.5
1
3
2
1
0.5
0
VDD = 5 V
RL = 600 Ω
CL = 100 pF
AV = –1
TA = 25°C
4
VO – Output Voltage – V
2.5
VO – Output Voltage – V
INVERTING LARGE-SIGNAL PULSE
RESPONSE†
0
0
0.5
1
1.5
2 2.5 3 3.5
t – Time – µs
4
4.5
5
0
0.5
1
1.5
3
3.5
4
4.5
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE†
5
3
VDD = 3 V
RL = 600 Ω
CL = 100 pF
AV = 1
TA = 25°C
VDD = 5 V
RL = 600 Ω
CL = 100 pF
AV = 1
TA = 25°C
4
VO – Output Voltage – V
2.5
2
1.5
1
3
2
1
0.5
0
0
1
2
3
4
5
6
7
8
9
10
0
1
t – Time – µs
2
3
4
5
6
t – Time – µs
7
8
9
Figure 38
Figure 37
† For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
20
5
Figure 36
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE†
VO – Output Voltage – V
2.5
t – Time – µs
Figure 35
0
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
10
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
INVERTING SMALL-SIGNAL
PULSE RESPONSE†
INVERTING SMALL-SIGNAL
PULSE RESPONSE†
1.56
VDD = 5 V
RL = 600 Ω
CL = 100 pF
AV = – 1
TA = 25°C
2.54
VO
VO – Output Voltage – V
1.54
VO – Output Voltage – V
2.56
VDD = 3 V
RL = 600 Ω
CL = 100 pF
AV = – 1
TA = 25°C
1.52
1.5
1.48
2.52
2.5
2.48
2.46
1.46
0
0.1
0.2
0.3
0.4 0.5 0.6
0.7
0.8
0.9
1
0
0.1
0.2 0.3
t – Time – µs
Figure 39
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE†
2.56
1.56
VDD = 3 V
RL = 600 Ω
CL = 100 pF
AV = 1
TA = 25°C
VDD = 5 V
RL = 600 Ω
CL = 100 pF
AV = 1
TA = 25°C
2.54
VO
VO – Output Voltage – V
VO
VO – Output Voltage – V
1
Figure 40
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE†
1.54
0.4 0.5 0.6 0.7 0.8 0.9
t – Time – µs
1.52
1.5
2.52
2.5
2.48
1.48
1.48
2.46
0 0.25 0.5 0.75
1 1.25 1.5 1.75
t – Time – µs
2
2.25 2.50
0
0.25 0.5 0.75
Figure 41
1 1.25 1.5 1.75
t – Time – µs
2
2.25 2.5
Figure 42
† For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
21
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
EQUIVALENT INPUT NOISE VOLTAGE†
vs
FREQUENCY
EQUIVALENT INPUT NOISE VOLTAGE†
vs
FREQUENCY
120
VDD = 3 V
RS = 20 Ω
TA = 25°C
100
V n – Equivalent Input Noise Voltage – nV/ Hz
V n – Equivalent Input Noise Voltage – nV/ Hz
120
80
60
40
20
0
10 1
10 2
10 3
f – Frequency – Hz
VDD = 5 V
RS = 20 Ω
TA = 25°C
100
80
60
40
20
0
101
10 4
10 2
10 3
f – Frequency – Hz
Figure 43
Figure 44
THD + N – Total Harmonic Distortion Plus Noise – %
INPUT NOISE VOLTAGE OVER
A 10-SECOND PERIOD†
1000
VDD = 5 V
f = 0.1 Hz to 10 Hz
TA = 25°C
750
Noise Voltage – nV
500
250
0
– 250
– 500
– 750
– 1000
0
2
4
6
t – Time – s
10 4
8
10
TOTAL HARMONIC DISTORTION PLUS NOISE†
vs
FREQUENCY
10
AV = 10
VDD = 5 V
TA = 25°C
AV = 100
AV = 1
1
AV = 100
RL = 600 Ω to 2.5 V
RL = 600 Ω to 0 V
0.1
AV = 10
0.01
101
AV = 1
10 2
10 3
10 4
f – Frequency – Hz
Figure 45
Figure 46
† For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
22
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
10 5
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
GAIN-BANDWIDTH PRODUCT ‡
vs
SUPPLY VOLTAGE
GAIN-BANDWIDTH PRODUCT †‡
vs
FREE-AIR TEMPERATURE
2.5
3.5
VDD = 5 V
f = 10 kHz
RL = 600 Ω
CL = 100 pF
Gain-Bandwidth Product – kHz
Gain-Bandwidth Product – kHz
4
3
2.5
2
RL = 600 Ω
CL = 100 pF
TA = 25°C
2.25
2
1.75
1.5
1
– 75
1.5
– 50 – 25
0
25
50
75
100
125
0
1
TA – Free-Air Temperature – °C
2
3
4
5
6
VDD – Supply Voltage – V
Figure 47
8
Figure 48
GAIN MARGIN‡
vs
LOAD CAPACITANCE
GAIN MARGIN‡
vs
LOAD CAPACITANCE
20
20
TA = 25°
RL = ∞
TA = 25°
RL = 600 Ω
Rnull = 100 Ω
Rnull = 100 Ω
15
15
Rnull = 500 Ω
Gain Margin – dB
Gain Margin – dB
7
Rnull = 1000 Ω
10
Rnull = 50 Ω
5
Rnull = 500 Ω
Rnull = 50 Ω
10
5
Rnull = 0
Rnull = 0
0
101
10 2
10 3
10 4
CL – Load Capacitance – pF
10 5
0
101
Figure 49
10 2
10 3
10 4
CL – Load Capacitance – pF
10 5
Figure 50
† Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
‡ For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
23
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
TYPICAL CHARACTERISTICS
PHASE MARGIN†
vs
LOAD CAPACITANCE
PHASE MARGIN†
vs
LOAD CAPACITANCE
75°
75°
TA = 25°C
RL = ∞
Rnull = 1000 Ω
Rnull = 500 Ω
45°
30°
Rnull = 100 Ω
Rnull = 100 Ω
45°
30°
Rnull = 50 Ω
Rnull = 50 Ω
15°
Rnull = 500 Ω
60°
φom
m – Phase Margin
60°
φom
m – Phase Margin
TA = 25°C
RL = 600 Ω
Rnull = 0 Ω
15°
Rnull = 0
0°
101
10 2
10 3
10 4
CL – Load Capacitance – pF
0°
101
10 5
10 2
10 3
10 4
CL – Load Capacitance – pF
Figure 52
Figure 51
UNITY-GAIN BANDWIDTH†
vs
LOAD CAPACITANCE
UNITY-GAIN BANDWIDTH†
vs
LOAD CAPACITANCE
10
10
TA = 25°C
RL = 600 Ω
B1 – Unity-Gain Bandwidth – kHz
B1 – Unity-Gain Bandwidth – kHz
TA = 25°C
RL = ∞
1
ÁÁ
ÁÁ
0.1
10 2
1
ÁÁ
ÁÁ
10 3
10 4
10 5
0.1
10 2
CL – Load Capacitance – pF
Figure 53
10 3
10 4
CL – Load Capacitance – pF
Figure 54
† For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V.
24
10 5
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
10 5
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
APPLICATION INFORMATION
driving large capacitive loads
The TLV2731 is designed to drive larger capacitive loads than most CMOS operational amplifiers. Figure 49
through Figure 54 illustrate its ability to drive loads greater than 100 pF while maintaining good gain and phase
margins (Rnull = 0).
A small series resistor (Rnull) at the output of the device (see Figure 55) improves the gain and phase margins
when driving large capacitive loads. Figure 49 through Figure 52 show the effects of adding series resistances
of 50 Ω, 100 Ω, 500 Ω, and 1000 Ω. The addition of this series resistor has two effects: the first effect is that
it adds a zero to the transfer function and the second effect is that it reduces the frequency of the pole associated
with the output load in the transfer function.
The zero introduced to the transfer function is equal to the series resistance times the load capacitance. To
calculate the approximate improvement in phase margin, equation 1 can be used.
ǒ
Ǔ
+ tan–1 2 × π × UGBW × Rnull × CL
Where :
∆φ m1 + Improvement in phase margin
UGBW + Unity-gain bandwidth frequency
R null + Output series resistance
C L + Load capacitance
∆φ m1
(1)
The unity-gain bandwidth (UGBW) frequency decreases as the capacitive load increases (see Figure 53 and
Figure 54). To use equation 1, UGBW must be approximated from Figure 53 and Figure 54.
VDD +
VI
–
Rnull
+
VDD – / GND
CL
RL
Figure 55. Series-Resistance Circuit
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
25
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
APPLICATION INFORMATION
macromodel information
Macromodel information provided was derived using Microsim Parts, the model generation software used
with Microsim PSpice . The Boyle macromodel (see Note 6) and subcircuit in Figure 56 are generated using
the TLV2731 typical electrical and operating characteristics at TA = 25°C. Using this information, output
simulations of the following key parameters can be generated to a tolerance of 20% (in most cases):
D
D
D
D
D
D
D
D
D
D
D
D
Maximum positive output voltage swing
Maximum negative output voltage swing
Slew rate
Quiescent power dissipation
Input bias current
Open-loop voltage amplification
Unity-gain frequency
Common-mode rejection ratio
Phase margin
DC output resistance
AC output resistance
Short-circuit output current limit
NOTE 6: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers,” IEEE Journal
of Solid-State Circuits, SC-9, 353 (1974).
99
3
VDD +
9
RSS
10
J1
DP
VC
J2
IN +
11
RD1
VAD
DC
12
C1
R2
–
53
HLIM
–
+
C2
6
–
–
+
+
GCM
GA
–
RD2
–
RO1
DE
5
+
VE
.SUBCKT TLV2731 1 2 3 4 5
C1
11
12
13.51E–12
C2
6
7
50.00E–12
DC
5
53
DX
DE
54
5
DX
DLP
90
91
DX
DLN
92
90
DX
DP
4
3
DX
EGND
99
0
POLY (2) (3,0) (4,0) 0 .5 .5
FB
7
99
POLY (5) VB VC VE VLP
+ VLN 0 90.83E3 –10E3 10E3 10E3 –10E3
GA
6
0
11
12 314.2E–6
GCM
0
6
10
99 242.35E–9
ISS
3
10
DC
87.00E–6
HLIM
90
0
VLIM 1K
J1
11
2
10 JX
J2
12
1
10 JX
R2
6
9
100.0E3
OUT
RD1
60
11
3.183E3
RD2
60
12
3.183E3
R01
8
5
25
R02
7
99
25
RP
3
4
6.553E3
RSS
10
99
2.500E6
VAD
60
4
–.5
VB
9
0
DC 0
VC
3
53
DC .795
VE
54
4
DC .795
VLIM
7
8
DC 0
VLP
91
0
DC 12.4
VLN
0
92
DC 17.4
.MODEL DX D (IS=800.0E–18)
.MODEL JX PJF (IS=500.0E–15 BETA=2.939E–3
+ VTO=–.065)
.ENDS
Figure 56. Boyle Macromodel and Subcircuit
PSpice and Parts are trademark of MicroSim Corporation.
Macromodels, simulation models, or other models provided by TI,
directly or indirectly, are not warranted by TI as fully representing
all of the specification and operating characteristics of the
semiconductor product to which the model relates.
26
–
VLIM
8
54
4
91
+
VLP
7
60
+
–
+ DLP
90
RO2
VB
IN –
VDD –
92
FB
–
+
ISS
RP
2
1
DLN
EGND +
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
VLN
TLV2731, TLV2731Y
Advanced LinCMOS RAIL-TO-RAIL
LOW-POWER SINGLE OPERATIONAL AMPLIFIERS
SLOS198A – AUGUST 1997 – REVISED MARCH 2001
MECHANICAL INFORMATION
DBV (R-PDSO-G5)
PLASTIC SMALL-OUTLINE PACKAGE
0,40
0,20
0,95
5
0,25 M
4
1,80
1,50
1
0,15 NOM
3,00
2,50
3
Gage Plane
3,10
2,70
0,25
0°– 8°
0,55
0,35
Seating Plane
1,30
1,00
0,10
0,05 MIN
4073253-4/A 12/96
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions include mold flash or protrusion.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
27
PACKAGE OPTION ADDENDUM
www.ti.com
4-Mar-2008
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TBD
Lead/Ball Finish
Call TI
MSL Peak Temp (3)
TLV2731CDBV
OBSOLETE
SOT-23
DBV
5
TLV2731CDBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Call TI
Level-1-260C-UNLIM
TLV2731CDBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2731CDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2731CDBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2731IDBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2731IDBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2731IDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLV2731IDBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
Diameter Width
(mm) W1 (mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
TLV2731CDBVR
SOT-23
DBV
5
3000
180.0
TLV2731CDBVT
SOT-23
DBV
5
250
TLV2731IDBVR
SOT-23
DBV
5
3000
TLV2731IDBVT
SOT-23
DBV
5
250
9.0
3.15
3.2
1.4
4.0
8.0
Q3
180.0
9.0
3.15
3.2
1.4
4.0
8.0
Q3
180.0
9.0
3.15
3.2
1.4
4.0
8.0
Q3
180.0
9.0
3.15
3.2
1.4
4.0
8.0
Q3
Pack Materials-Page 1
W
Pin1
(mm) Quadrant
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Mar-2008
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TLV2731CDBVR
SOT-23
DBV
5
3000
182.0
182.0
20.0
TLV2731CDBVT
SOT-23
DBV
5
250
182.0
182.0
20.0
TLV2731IDBVR
SOT-23
DBV
5
3000
182.0
182.0
20.0
TLV2731IDBVT
SOT-23
DBV
5
250
182.0
182.0
20.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2008, Texas Instruments Incorporated