HJ SERIES LOW COST TRIPLE HDTV FILTERS The HJ range of HDTV filters are ideally suited to monitor outputs where low cost is the prime objective. Triple package and SMD keep production costs at a minimum. • • Low cost Monitor quality • • Pre and Post, Luminance and Chrominance filters Miniature size triple filters Channel Description Filter Shape Sampling Frequency Insertion Loss at 100 kHz End Of Passband Passband Amplitude Ripple Atten @ ½ S.F. Start Of Stopband Stopband Attenuation wrt 100 kHz Y, R, G, B U, V Lowpass Lowpass 74.25 MHz 37.125 MHz < 1.0 dB < 1.0 dB 30.0 MHz 14.5 MHz < 0.5 dB < 0.5 dB 12 ± 3 dB 12 ± 3 dB 44.25 MHz 22.625 MHz > 35 dB target > 35 dB target > 30 dB spec > 30 dB spec Stopband Measured To 100 MHz 100 MHz Delay Time at 200 kHz Single clock cycle delay between Luma and Chroma channels Rejection Notch@ S.F. Impedance Temperature Range Aqueous Washable SMD Reflow Limitations as Package > 45 dB > 45 dB 75 ohms 75 ohms 0 0 to 70 C 0 to 70 0C Yes Yes Data Sheet Fara309 Data Sheet Fara309 DR00293D DR00293D Order Codes HJYUVF – HDTV 4:2:2 Sampling Antialiasing Filter HJRGBF – HDTV 4:2:2 Sampling Antialiasing Filter HJYUVS – HDTV 4:2:2 Sampling Reconstruction Filter with sinx/x correction. HJRGBS – HDTV 4:2:2 Sampling Reconstruction Filter with sinx/x correction. Connection Diagram Available on Request © Faraday Technology. As part of continual product improvement the specifications, details and dimensions shown in this publication are subject to change without notice Fara227d Page 1 of 2 Sep-03(B) PACKAGE DETAIL All dimensions in millimetres (inches). Gen Tolerance ± 0,05 (0.002) unless otherwise stated. DO NOT SCALE © Faraday Technology Ltd Croft Road Newcastle-U-Lyme ST5 0QZ England Tel (044) 01782 661501 Fax 630101 24,13 (0.95) 9,91 (0.39) O/ALL Third Angle Projection 17,78 (0.7) 0,25 (0.01) 2,54 (0.1) Typ 0,5 (0.02) 18,29 (0.72) Max 9 TOP VIEW 1 8 0,48 (0.019) Typ Notes. a. Surface Mount terminals;- 0,254 Alloy 42 Electroplate 2,5- 7,6u bright Sn90 over 1,2 - 2,5u of nickel underplating, meeting solderability requirements of MIL STD 202F Method 208F. b. Pin assignments;- Pin 1 = Input A Pin 16 = Output A Pin 4 = Input B Pin 13 = Output B Pin 7 = Input C Pin 10 = Output C Pins 9, 12 & 15 = H.F. Boost. All remaining pins = Gnd. c. For YUV filter, Y channel is channel A. Template: DT00292 Change Note No; 1088 Faraday Technology Ltd. Croft Road Industrial Estate, Newcastle, Staffordshire ST5 0QZ. England. Fara227d Auth: A Mason Date: 01/09/03 Date: 01/09/03 Title: Drg No: FILTER ASSY OUTLINE Tel: Fax: Email: Web site: Page 2 of 2 DR00293D A4DRGBLK.CDR 14,35 (0.565) 16 0,85 (0.033) 3,175 (0.125) + 44 (0)1782 661501 + 44 (0)1782 630101 [email protected] http://www.faradaytech.co.uk Sep-03(B)