D200RW Series Miniature SIP, 2W Wide Input Range DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 2W Output Power • 2:1 Input Voltage Range Input Parameter Input Voltage Range • 1,000 VDC Isolation • Short Circuit Protected • Miniature SIP Case • Single & Dual Outputs Input Filter Input Reflected Ripple Current Reverse Polarity Input Current Short Circuit Input Power • 2.7 MH MTBF Output • Industry Standard Pin-Out Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit Conditions Min. 5 VDC Input 4.5 12 VDC Input 9.0 24 VDC Input 18.0 48 VDC Input 36.0 Capacitor Filter Typ. 5.0 12.0 24.0 48.0 Max. 9.0 18.0 36.0 72.0 35 1.0 1,500 Conditions Min. Typ. ±2.0 Max. ±2.0 ±0.5 ±1.0 80 Vin = Min to Max Iout = 25% to 100% 120 ±0.02 Units VDC mA P - P A mW Units % % % % mV P - P % %/°C Continuous (Autorecovery) General RoHS Compliant Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds 1,000 VDC 100 kHz, 1V Min. 1,000 1,000 Typ. Max. 650 Units VDC MΩ pF kHz Max. +85 +100 +125 Units °C °C °C 95 % 60 100 Environmental Parameter Operating Temperature Range Operating Temperature Range Storage Temperature Range Cooling Humidity Conditions Ambient Case Min. -40 Typ. +25 -40 Free Air Convection RH, Non-condensing Physical MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Case Size Case Material Weight 0.86 x 0.36 x 0.44 Inches (21.89 x 9.2 x 11.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.17 Oz (4.8g) Remote On/Off Parameter Unit On (Note 2) Unit Off (Note 2) Off Idle Current Conditions Min. 0 Typ. Max. 0.8 5.0 Units VDC VDC mA 5.0 Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 2.73 Typ. Max. Units MHours Conditions Min. -0.7 -0.7 -0.7 -0.7 Typ. Max. 12.0 24.0 40.0 80.0 260 1,800 Units Absolute Maximum Ratings Parameter Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 5 VDC Input 12 VDC Input 24 VDC Input 48 VDC Input 1.5 mm From Case For 10 Sec All Models VDC °C mW Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. Model Selection Guide Model Number D201RW D202RW D203RW D204RW D205RW D206RW D207RW D208RW D211RW D212RW D213RW D214RW D215RW D216RW D217RW D218RW D221RW D222RW D223RW D224RW D225RW D226RW D227RW D228RW D231RW D232RW D233RW D234RW D235RW D236RW D237RW D238RW Input Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load 5 4.5 - 9.0 492 15 5 4.5 - 9.0 571 15 5 4.5 - 9.0 555 30 5 4.5 - 9.0 547 30 5 4.5 - 9.0 571 20 5 4.5 - 9.0 533 25 5 4.5 - 9.0 533 25 5 4.5 - 9.0 563 60 12 9.0 - 18.0 205 15 12 9.0 - 18.0 216 15 12 9.0 - 18.0 208 15 12 9.0 - 18.0 213 15 12 9.0 - 18.0 222 15 12 9.0 - 18.0 208 15 12 9.0 - 18.0 210 15 12 9.0 - 18.0 219 30 24 18.0 - 36.0 98 8 24 18.0 - 36.0 108 8 24 18.0 - 36.0 104 8 24 18.0 - 36.0 104 8 24 18.0 - 36.0 106 8 24 18.0 - 36.0 104 8 24 18.0 - 36.0 104 8 24 18.0 - 36.0 106 20 48 36.0 - 72.0 48 6 48 36.0 - 72.0 56 6 48 36.0 - 72.0 53 6 48 36.0 - 72.0 53 6 48 36.0 - 72.0 56 6 48 36.0 - 72.0 53 6 48 36.0 - 72.0 52 6 48 36.0 - 72.0 55 12 Output Capacitive Efficiency Load Voltage Current Current (%, Typ) (µF, Max) (VDC) (mA, Max) (mA, Min) 3.3 500.0 125.0 67 3,300 5.0 400.0 100.0 70 3,300 12.0 167.0 42.0 72 470 15.0 133.0 33.0 73 470 ±5.0 ±200.0 ±50.0 70 ±1,000 ±12.0 ±83.0 ±21.0 75 ±220 ±15.0 ±67.0 ±17.0 75 ±220 ±24.0 ±42.0 ±10.0 71 ±100 3.3 500.0 125.0 67 3,300 5.0 400.0 100.0 77 3,300 12.0 167.0 42.0 80 470 15.0 133.0 33.0 78 470 ±5.0 ±200.0 ±50.0 75 ±1,000 ±12.0 ±83.0 ±21.0 80 ±220 ±15.0 ±67.0 ±17.0 79 ±220 ±24.0 ±42.0 ±10.0 76 ±100 3.3 500.0 125.0 70 3,300 5.0 400.0 100.0 77 3,300 12.0 167.0 42.0 80 470 15.0 133.0 33.0 80 470 ±5.0 ±200.0 ±50.0 78 ±1,000 ±12.0 ±83.0 ±21.0 80 ±220 ±15.0 ±67.0 ±17.0 80 ±220 ±24.0 ±42.0 ±10.0 78 ±100 3.3 500.0 125.0 71 3,300 5.0 400.0 100.0 74 3,300 12.0 167.0 42.0 78 470 15.0 133.0 33.0 78 470 ±5.0 ±200.0 ±50.0 74 ±1,000 ±12.0 ±83.0 ±21.0 79 ±220 ±15.0 ±67.0 ±17.0 80 ±220 ±24.0 ±42.0 ±10.0 75 ±100 Fuse Rating Slow-Blow (mA) 1,500 1,500 1,500 1,500 1,500 1,500 1,500 1,500 700 700 700 700 700 700 700 700 350 350 350 350 350 350 350 350 135 135 135 135 135 135 135 135 Mechanical Dimensions Other input/output combinations are available (i.e. 9.0 VDC). Contact the factory for details at: [email protected] Notes: 1. An external capacitor should be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. For single output units a 100 µF is recommended, for dual output models ±48 µF should be used. 2. The Remote On/Off Control input (Pin 3) is referenced to -Vin (Pin 1). Connection to the pin should be made through a 1kΩ resistor and diode (1N4148). If it is not used, the control pin should be left open or tied directly to -Vin (Pin 1). 3. Operation at no-load will not damage these units. However, they may not meet all specifications. 4. Dual output units may be connected to provide a 10 VDC, 24 VDC, 30 VDC or 48 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Derating Curve A metal case is available Contact the factory for details at: [email protected] Pin Connections Pin 1 2 3 5 6 7 8 Mechanical Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) MicroPower Direct Single Dual -Vin -Vin +Vin +Vin Remote ON/OFF NC NC +Vout +Vout -Vout Common NC -Vout NC = No Connection www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]