Product Guide 1113F Series, Right Angle SMT LED ■ Features ■ Applications • Smaller size while maintaining the same brightness • levels as the 1101F series • Excellent for edge lighting • Portable devices • Computers • Industrial / medical instrumentation ■ Outline Dimensions Cathode Mark Cathode Unit: mm Tolerances + 0.1 ■ Electro-Optical Characteristics Part No. Luminous Intensity IV Material Emitted Lens Color Color IF Dominant λd TYP. GaAIAs Red PY1113F GaP Yellow-Green PG1113F GaP Green Units Milky 7 11.7 20 660 647 White 7 11.7 20 570 560 TYP. 3.8 6.4 20 mcd mA Forward Voltage V Wavelength Peak λp TYP. MIN. BR1113F (Ta=25°C) Spectral Line Half Width λ ∆λ TYP. Reverse Viewing Current IR Angle F IF TYP. MAX. IF MAX. VR 30 20 1.7 2.3 20 100 4 572 30 20 2.1 2.8 20 100 4 567 30 20 2.1 2.8 20 100 4 mA µA V nm mA V (2 θ 1/2) 130° 150° Deg. ■ Absolute Maximum Ratings (Ta=25°C) Red Green Yellow-Green Units Item Symbol BR PY PG Pd 57.5 70 70 mW Forward Current IF 25 25 25 mA Peak Forward Current IFM 60 60 60 mA Reverse Voltage VR 4 4 4 V Power Dissipation Operating Temperature Topr -30 to +85 °C Storage Temperature Tstg -40 to +100 °C ∆IF 0.36 (DC) 0.86 (Pulse) mA/°C Derating* * Ta=25°C, IFM applies for the pulse width ≤ 1msec. and duty cycle ≤1/20. ■ Taping Specifications 4+0.1 φ 1.5 +0.1 0 (1.1) (0.2) 1.75+0.1 ■ Operation Current Derating Chart (DC) 3.5+0.05 2+0.05 (φ 0.6) (2.2) 8+0.2 Center Hole Center Hole Quantity on tape: 4000 pieces per reel (0.8) 2+0.5 φ 21+0.8 4+0.1 Direction to pull BR, PY, PG, +1 φ 60 -0 φ 13+0.2 φ 13+0.2 9+0.3 11.4+1 +0 φ 180 3 ■ Precautions Please follow these handling precautions to prevent damage to the chip and ensure its reliability. 1. Soldering conditions: • Soldering iron: Temperature at tip of iron: 280°C max. (30W max.) Soldering time: 3 sec. max. • Dip soldering: Preheating: 120 ~ 150°C max. (resin surface temp.) 60 ~ 120 sec. max. Bath temperature: 260°C max. Dipping Time: 5 sec. max. • Reflow Soldering: °C Operation Heating 240 150 ~ LED Surface Temperature ■ Spatial Distribution Pre-heating Temperature rise: 5°C/sec. Cooling: —5°C/sec. 120 0 60 to 120 sec. 5 sec. max 2. Cleaning: • If cleaning is required, use the following solutions for less than 1 minute, at less than 40°C. • Appropriate chemicals: Ethyl alcohol and isopropyl alcohol. • Effect of ultrasonic cleaning on the LED resin body differs depending on such factors as the oscillator output, size of PCB and LED mounting method. The use of ultrasonic cleaning should be enforced at proper output after confirming there is no problem. Product specifications subject to change without notice. PG__1113F-0301 Stanley Electric Sales of America, Inc. 2660 Barranca Parkway, Irvine, CA 92606 • Tel: 800-LED-LCD1 (533-5231) • Fax: 949-222-0555 Website: www.stanley-electric.com