Preset counters electronic 1 preset, timer programmable Display LED, 5-digits, programmable NE210 Features –– Preset counter with one preset –– Display 5-digits –– Operating mode, start count, scaling factor programmable –– Connection: Incremental encoder or digital sensors –– Time meter with four time ranges –– Time relay with operation and release delay –– Programmable as a time counter NE210 - LED Preset counter Technical data - electrical ratings Technical data - electrical ratings Voltage supply 22...50 VAC (50/60 Hz) 85...265 VAC (50/60 Hz) 24 VDC ±10 % Programmable parameters Power consumption 5 VA, 5 W Sensor supply 24 VDC ±20 % / 100 mA Operating modes Sensor logic Scaling factor Count mode Time relay function Display LED, 7-segment display Approvals UL/cUL, CE conform Number of digits 5-digits Digit height 7.6 mm Function Preset counter Main counter with 1 preset Operating temperature 0...+50 °C Storing temperature -20...+70 °C Scaling factor 0.001...99.999 Relative humidity 80 % non-condensing Count modes Adding or subtracting A-B (difference counting) A+B total (parallel counting) Up/Down A 90° B phase evaluation E-connection Plug-in screw terminals Core cross-section 1.5 mm² Protection DIN EN 60529 IP 65 face with seal Operation / keypad Membrane with softkeys Counting frequency 15 Hz, 10 kHz (set by Dip switch) Housing type Built-in housing Operating modes Main preset, Time meter / time relay Dimensions W x H x L 48 x 48 x 108 mm Installation depth 108 mm Data memory >10 years in EEPROM Mounting Clip frame Reset Button, electric or automatic Cutout dimensions 45 x 45 mm (+0.6) Outputs electronic NPN / PNP transistor switch Materials Outputs relay Potential-free change-over contact Housing: Makrolon 6485 (PC) Keypad: Polyester Weight approx. 150 g Output holding time 0.01...99.99 s Standard DIN EN 61010‑1 Protection class II Overvoltage category II Pollution degree 2 Emitted interference DIN EN 61000-6-4 Interference immunity DIN EN 61000-6-2 www.baumerivo.com 30/10/2008 1 Subject to modification in technic and design. Errors and omissions excepted. Technical data - mechanical design Preset counters electronic 1 preset, timer programmable Display LED, 5-digits, programmable NE210 Part number Block circuit diagram AXA1 Voltage supply Voltage supply 1 22...50 VAC 2 85...265 VAC 3 24 VDC 2 + 3 12 13 Signal input A 7 B 8 Reset Outputs Relay output Relay, signal output PNP Relay, signal output NPN Without relay, signal output PNP Coding for input logic NPN Br. 11-13 PNP Br. 11-12 A 90°B 9 Main counter with 1 preset start count scaling factor 5 10 Trigger level Control inputs PNP- / NPN-logic Adaptor plates (page %S) Count input Z 118.033 Adaptor plate for screw mount, face 60 x 75 mm Trigger current 9...16 mA Adaptor plate for clip mount, face 53.2 x 53.2 mm Switch-off current <0.5 mA Input resistance 1.65 kΩ Reset input Adaptor plate for clip mount, face 60 x 75 mm Connection diagram 11 10 9 6 5 Electr. output 4 7 B A Count Reset NPN Br. 11-13 PNP Br. 11-12 Sensor supply +24V 0V 8 3 Trigger current 5...8 mA Switch-off current <0.5 mA Input resistance 3.3 kΩ Relay output Output circuit Switching voltage max. 250 VAC / 110 VDC Switching current max. 1A Switching capacity max. 150 VA / 30 W Relay responding time 5 ms Electronical outputs Output circuit PNP-switching transistor Open collector 2 1 End contact Supply voltage 12 electr. output 11 Input circuit 13 Relay output 6 Timer Time relay Optocoupler inputs Z 118.035 + 4 Accessories Z 118.034 Sensor supply - Switching voltage 24 VDC ±20% Switching current max. 10 mA (AC) 50 mA (DC) NPN-switching transistor Open collector max. 265 V terminal - terminal / - terminal Switching voltage max. 35 V Switching current max. 50 mA Dimensions 60.8 48 7 108 1-6 48 18.5 2 www.baumerivo.com Subject to modification in technic and design. Errors and omissions excepted. 1 2 3 4 - 30/10/2008 NE210.0