LINER LTC2362CS6

LTC2360/LTC2361/LTC2362
100ksps/250ksps/500ksps,
12-Bit Serial ADCs in TSOT-23
DESCRIPTION
FEATURES
n
n
n
n
n
n
n
n
n
n
n
n
12-Bit Resolution
Low Noise: 73dB SNR
Low Power Dissipation: 1.5mW @ 100ksps
100ksps/250ksps/500ksps Sampling Rates
Single Supply 2.35V to 3.6V Operation
No Data Latency
Sleep Mode with 0.1μA Typical Supply Current
Dedicated External Reference (TSOT23-8)
1V to 3.6V Digital Output Supply (TSOT23-8)
SPI/MICROWIRE™ Compatible Serial I/O
Guaranteed Operation from –40°C to 125°C
Tiny 6- and 8-Lead TSOT-23 Packages
APPLICATIONS
n
n
n
n
n
n
The LTC®2360/LTC2361/LTC2362 are 100ksps/250ksps/
500ksps, 12-bit, sampling A/D converters that draw only
0.5mA, 0.75mA and 1.1mA, respectively, from a single
3V supply. The supply current drops at lower sampling
rates because these devices automatically power down
after conversions. The full-scale input of the LTC2360/
LTC2361/LTC2362 is 0V to VDD or VREF. These ADCs are
available in tiny 6- and 8-lead TSOT-23 packages.
The serial interface, tiny TSOT-23 package and extremely
high sample rate-to-power ratio make the LTC2360/
LTC2361/LTC2362 ideal for compact, low power, high
speed systems.
The high impedance single-ended analog input and the
ability to operate with reduced spans (down to 1.4V full
scale) allow direct connection to sensors and transducers in
many applications, eliminating the need for gain stages.
Communication Systems
Data Acquisition Systems
Handheld Portable Devices
Uninterrupted Power Supplies
Battery-Operated Systems
Automotive
L, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
All other trademarks are the property of their respective owners.
TYPICAL APPLICATION
12-Bit TSOT23-6/-8 ADC Family
DATA OUTPUT RATE
3Msps
1Msps
500ksps
250ksps
100ksps
Part Number
LTC2366
LTC2365
LTC2362
LTC2361
LTC2360
Single 3V Supply, 500ksps, 12-Bit Sampling ADC
Supply Current vs Sample Rate
1200
3V
LTC2362
VDD
CONV
VREF
SCK
GND
SDO
AIN
OVDD
SERIAL DATA LINK TO
ASIC, PLD, MPU, DSP
OR SHIFT REGISTORS
DIGITAL OUTPUT SUPPLY
1V TO 3.6V
2.2μF
236012 TA01a
SUPPLY CURRENT (μA)
1000
2.2μF
ANALOG INPUT
0V TO 3V
VDD = 3.6V
TA = 25°C
800
LTC2361
600
LTC2362
400
LTC2360
200
0
1
10
100
SAMPLE RATE (ksps)
1000
236012 TA01b
236012f
1
LTC2360/LTC2361/LTC2362
ABSOLUTE MAXIMUM RATINGS
(Notes 1, 2)
Supply Voltage (VDD, OVDD)........................................4V
VREF and Analog Input Voltage
(Note 3).........................................–0.3V to (VDD + 0.3V)
Digital Input Voltage......................–0.3V to (VDD + 0.3V)
Digital Output Voltage ...................–0.3V to (VDD + 0.3V)
Power Dissipation ...............................................100mW
Operating Temperature Range
LTC2360C/LTC2361C/LTC2362C .............. 0°C to 70°C
LTC2360I/LTC2361I/LTC2362I.............. –40°C to 85°C
LTC2360H/LTC2361H/LTC2362H (Note 12).. –40°C to 125°C
Storage Temperature Range................... –65°C to 150°C
Lead Temperature (Soldering, 10 sec) .................. 300°C
PIN CONFIGURATION
TOP VIEW
VDD 1
VREF 2
GND 3
AIN 4
TOP VIEW
8 CONV
7 SCK
6 SDO
5 OVDD
VDD 1
6 CONV
GND 2
5 SDO
AIN 3
4 SCK
TS8 PACKAGE
8-LEAD PLASTIC TSOT-23
S6 PACKAGE
6-LEAD PLASTIC TSOT-23
TJMAX = 150°C, θJA = 250°C/W
TJMAX = 150°C, θJA = 250°C/W
ORDER INFORMATION
Lead Free Finish
TAPE AND REEL (MINI)
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LTC2362CTS8#TRMPBF
LTC2362CTS8#TRPBF
LTDBV
8-Lead Plastic TSOT23
0°C to 70°C
LTC2362ITS8#TRMPBF
LTC2362ITS8#TRPBF
LTDBV
8-Lead Plastic TSOT23
-40°C to 85°C
LTC2362HTS8#TRMPBF
LTC2362HTS8#TRPBF
LTDBV
8-Lead Plastic TSOT23
-40°C to 125°C
LTC2362CS6#TRMPBF
LTC2362CS6#TRPBF
LTDGP
6-Lead Plastic TSOT23
0°C to 70°C
LTC2362IS6#TRMPBF
LTC2362IS6#TRPBF
LTDGP
6-Lead Plastic TSOT23
-40°C to 85°C
LTC2362HS6#TRMPBF
LTC2362HS6#TRPBF
LTDGP
6-Lead Plastic TSOT23
-40°C to 125°C
LTC2361CTS8#TRMPBF
LTC2361CTS8#TRPBF
LTDGM
8-Lead Plastic TSOT23
0°C to 70°C
LTC2361ITS8#TRMPBF
LTC2361ITS8#TRPBF
LTDGM
8-Lead Plastic TSOT23
-40°C to 85°C
LTC2361HTS8#TRMPBF
LTC2361HTS8#TRPBF
LTDGM
8-Lead Plastic TSOT23
-40°C to 125°C
LTC2361CS6#TRMPBF
LTC2361CS6#TRPBF
LTDGN
6-Lead Plastic TSOT23
0°C to 70°C
LTC2361IS6#TRMPBF
LTC2361IS6#TRPBF
LTDGN
6-Lead Plastic TSOT23
-40°C to 85°C
LTC2361HS6#TRMPBF
LTC2361HS6#TRPBF
LTDGN
6-Lead Plastic TSOT23
-40°C to 125°C
LTC2360CTS8#TRMPBF
LTC2360CTS8#TRPBF
LTDGJ
8-Lead Plastic TSOT23
0°C to 70°C
LTC2360ITS8#TRMPBF
LTC2360ITS8#TRPBF
LTDGJ
8-Lead Plastic TSOT23
-40°C to 85°C
LTC2360HTS8#TRMPBF
LTC2360HTS8#TRPBF
LTDGJ
8-Lead Plastic TSOT23
-40°C to 125°C
LTC2360CS6#TRMPBF
LTC2360CS6#TRPBF
LTDGK
6-Lead Plastic TSOT23
0°C to 70°C
LTC2360IS6#TRMPBF
LTC2360IS6#TRPBF
LTDGK
6-Lead Plastic TSOT23
-40°C to 85°C
LTC2360HS6#TRMPBF
LTC2360HS6#TRPBF
LTDGK
6-Lead Plastic TSOT23
TRM = 500 pieces. *Temperature grades are identified by a label on the shipping container.
Consult LTC Marketing for information on lead based finish parts.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
-40°C to 125°C
236012f
2
LTC2360/LTC2361/LTC2362
CONVERTER CHARACTERISTICS
The l denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at TA = 25°C. (Note 4)
PARAMETER
CONDITIONS
MIN
l
Resolution (No Missing Codes)
TYP
MAX
UNITS
12
Bits
(Notes 5, 6)
l
±0.25
±1
Differential Linearity Error
(Note 6)
l
±0.25
±1
Transition Noise
(Note 7)
Offset Error
(Note 6)
l
1
±3.5
LSB
Gain Error
(Note 6)
l
0.1
±2
LSB
Total Unadjusted Error
(Note 6)
l
1.1
±3.5
LSB
Integral Linearity Error
0.25
LSB
LSB
LSBRMS
ANALOG INPUT
The l denotes the specifications which apply over the full operating temperature range, otherwise
specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
CONDITIONS
MIN
VIN
Analog Input Voltage
S6 Package
TS8 Package
l
l
IIN
Analog Input Leakage Current
CONV = High
l
CIN
Analog Input Capacitance
Between Conversions
During Conversions
VREF
Reference Input Voltage
TS8 Package
l
IREF
Reference Input Leakage Current
TS8 Package
l
CREF
Reference Input Capacitance
TS8 Package
tAP
Sample-and-Hold Aperture Delay Time
tJITTER
Sample-and-Hold Aperture Delay Time Jitter
TYP
MAX
–0.05
–0.05
UNITS
VDD + 0.05
VREF + 0.05
V
±1
μA
20
4
pF
pF
1.4
VDD + 0.05
V
±1
μA
20
pF
1
ns
0.3
ns
DYNAMIC ACCURACY
The l denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
SINAD
Signal-to-(Noise + Distortion) Ratio
fIN = 49kHz for LTC2360/LTC2361,
fIN = 100kHz for LTC2362
72
dB
SNR
Signal-to-Noise Ratio
fIN = 49kHz for LTC2360/LTC2361,
fIN = 100kHz for LTC2362
73
dB
THD
Total Harmonic Distortion
fIN = 49kHz for LTC2360/LTC2361,
fIN = 100kHz for LTC2362
–85
dB
SFDR
Spurious Free Dynamic Range
fIN = 49kHz for LTC2360/LTC2361,
fIN = 100kHz for LTC2362
86
dB
IMD
Intermodulation Distortion
fIN1 = 97kHz, fIN2 = 100kHz for LTC2362
fIN1 = 47kHz, fIN2 = 49kHz for LTC2360/LTC2361
–75
dB
Full-Power Bandwidth
at 3dB
at 0.1dB
10
2
MHz
MHz
Full-Linear Bandwidth
SINAD ≥ 68dB
1
MHz
236012f
3
LTC2360/LTC2361/LTC2362
DIGITAL INPUTS AND DIGITAL OUTPUTS
The l denotes the specifications which apply over the
full operating temperature range, otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
CONDITIONS
VIH
High Level Input Voltage
2.7V < VDD ≤ 3.6V
2.35V ≤ VDD ≤ 2.7V
l
l
MIN
TYP
MAX
VIL
Low Level Input Voltage
2.7V < VDD ≤ 3.6V
2.35V ≤ VDD ≤ 2.7V
l
l
0.8
0.7
V
V
IIH
High Level Input Current
VIN = VDD
l
2.5
μA
VIN = 0V
l
–2.5
μA
2
1.7
UNITS
V
V
IIL
Low Level Input Current
CIN
Digital Input Capacitance
VOH
High Level Output Voltage
VDD = 2.35V to 3.6V, ISOURCE = 200μA
l
VOL
Low Level Output Voltage
VDD = 2.35V to 3.6V, ISINK = 200μA
l
0.2
V
IOZ
Hi-Z Output Leakage
CONV = VDD
l
±3
μA
2
pF
VDD – 0.2
V
COZ
Hi-Z Output Capacitance
CONV = VDD
4
pF
ISOURCE
Output Source Current
VOUT = 0V
–10
mA
ISINK
Output Sink Current
VOUT = VDD
10
mA
POWER REQUIREMENT
The l denotes the specifications which apply over the full operating temperature range,
otherwise specifications are at TA = 25°C. (Note 4)
SYMBOL
PARAMETER
VDD
Supply Voltage
OVDD
Digital Output Supply Voltage
IDD
Supply Current
Operational Mode, LTC2362
Operational Mode, LTC2361
Operational Mode, LTC2360
Sleep Mode
Sleep Mode
Sleep Mode
fSMPL = 500ksps
fSMPL = 250ksps
fSMPL = 100ksps
0°C to 70°C
–40°C to 85°C
–40°C to 125°C
l
l
l
l
l
l
Power Dissipation
Operational Mode, LTC2362
Operational Mode, LTC2361
Operational Mode, LTC2360
Sleep Mode
Sleep Mode
Sleep Mode
fSMPL = 500ksps
fSMPL = 250ksps
fSMPL = 100ksps
0°C to 70°C
–40°C to 85°C
–40°C to 125°C
l
l
l
l
l
l
PD
CONDITIONS
MIN
TYP
MAX
UNITS
l
2.35
3.0
3.6
V
l
1.0V
3.6
V
1.1
0.75
0.5
0.1
0.1
0.1
2
1.5
1
2
2
5
mA
mA
mA
μA
μA
μA
3.3
2.25
1.5
0.3
0.3
0.3
7.2
5.4
3.6
7.2
7.2
18
mW
mW
mW
μW
μW
μW
236012f
4
LTC2360/LTC2361/LTC2362
TIMING CHARACTERISTICS
The l denotes the specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 4)
LTC2360
SYMBOL
PARAMETER
CONDITIONS
fSMPL(MAX)
Maximum Sampling Frequency
(Notes 8, 9)
l
fSCK
Shift Clock Frequency
(Notes 8, 9)
l
tSCK
MIN
l
Shift Clock Period
TYP
100
MIN
TYP
LTC2362
MAX
250
100
MIN
TYP
MAX
500
10
50
MHz
2
μs
20
10
UNITS
kHz
25
40
l
tTHROUGHPUT Minimum Throughput Time, tACQ + tCONV
LTC2361
MAX
ns
4
tACQ
Acquisition Time
l
2
1
0.5
μs
tCONV
Conversion Time
l
8
3
1.5
μs
t1
Minimum Positive CONV Pulse Width
(Note 8)
l
8
3
1.5
μs
16
t2
SCK↑ Setup Time After CONV↓
(Note 8)
l
t3
SDO Enabled Time After CONV↓
(Notes 8, 9)
l
16
16
16
ns
t4
SDO Data Valid Access Time After SCK↓ (Notes 8, 9, 10) l
8
8
8
ns
t5
SCK Low Time
(Note 11)
l
40%
40%
40%
tSCK
t6
SCK High Time
(Note 11)
l
40%
40%
40%
tSCK
t7
SDO Data Valid Hold Time After SCK↓
(Notes 8, 9, 10) l
t8
SDO Into Hi-Z State Time After CONV↑
(Notes 8, 9)
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: All voltage values are with respect to GND.
Note 3: When pins AIN and VREF are taken below GND or above VDD,
they will be clamped by internal diodes. These products can handle input
currents greater than 100mA below GND or above VDD without latch-up.
Note 4: VDD = OVDD = VREF = 2.35V to 3.6V, fSMPL = fSMPL(MAX) and
fSCK = fSCK(MAX) unless otherwise specified.
Note 5: Integral linearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
16
4
16
4
6
ns
4
6
ns
6
ns
Note 6: Linearity, offset and gain specifications apply for a single-ended
AIN input with respect to GND.
Note 7: Typical RMS noise at code transitions.
Note 8: Guaranteed by characterization. All input signals are specified with
tr = tf = 2ns (10% to 90% of VDD) and timed from a voltage level of 1.6V.
Note 9: All timing specifications given are with a 10pF capacitance load.
With a capacitance load greater than this value, a digital buffer or latch
must be used.
Note 10: The time required for the output to cross the VIH or VIL voltage.
Note 11: Guaranteed by design, not subject to test.
Note 12: High temperatures degrade operating lifetimes. Operating lifetime
is derated at temperatures greater than 105°C.
236012f
5
LTC2360/LTC2361/LTC2362
TYPICAL PERFORMANCE CHARACTERISTICS
Differential Nonlinearity
vs Output Code
Integral Nonlinearity
vs Output Code
0.6
0.6
0.4
0.4
0.2
0.2
0
–0.2
–0.2
–0.4
–0.6
–0.6
–0.8
–0.8
–1
–1
512 1024 1536 2048 2560 3072 3584 4096
OUTPUT CODE
0
0.2
MAX INL
0
MIN DNL
–0.4
–0.6
–1
0.8
512 1024 1536 2048 2560 3072 3584 4096
OUTPUT CODE
20.0
VDD = 3.6V
SUPPLY CURRENT (μA)
REFERENCE CURRENT (μA)
400
8000
300
200
100
2000
0
2046
2047 2048
CODE
2049
2050
0
16.0
12.0
8.0
4.0
0.0
10 20 30 40 50 60 70 80 90 100
SAMPLING FREQUENCY (ksps)
0
10 20 30 40 50 60 70 80 90 100
SAMPLE RATE (ksps)
236012 G05
236012 G04
236012 G06
THD vs Input Frequency
SINAD vs Input Frequency
74
3.6
1.6
2
2.4 2.8 3.2
REFERENCE VOLTAGE (V)
Reference Current vs Sample
Rate (TS8 Package)
VDD = 3.6V
4000
1.2
236012 G03
500
VDD = 3V
6000
MIN INL
–0.2
Supply Current vs Sample Rate
10000
2045
MAX DNL
0.4
236012 G02
Histogram for 16384 Conversions
COUNT
0.6
–0.8
236012 G01
0
VDD = 3.6V
0.8
0
–0.4
0
1
VDD = 3V
0.8
DNL (LSB)
INL (LSB)
1
VDD = 3V
0.8
Integral and Differential Nonlinearity
vs Reference Voltage (TS8 Package)
NONLINEARITY ERROR (LSB)
1
TA = 25°C, VDD = OVDD = VREF (LTC2360, Note 4)
48kHz Sine Wave 8192 FFT Plot
–78
0
–80
–20
VDD = 3.6V
VDD = 3V
fSMPL = 100ksps
73
–82
72
71
VDD = 2.35V
MAGNITUDE (dB)
VDD = 2.35V
THD (dB)
SINAD (dB)
VDD = 3.0V
–84
VDD = 3.6V
–86
–88
–40
–60
–80
–100
70
–90
–120
VDD = 3.0V
69
–92
1
10
INPUT FREQUENCY (kHz)
100
236012 G07
1
10
INPUT FREQUENCY (kHz)
100
236012 G08
–140
0
10
30
20
40
INPUT FREQUENCY (kHz)
50
2306012 G09
236012f
6
LTC2360/LTC2361/LTC2362
TYPICAL PERFORMANCE CHARACTERISTICS
Integral Nonlinearity
vs Output Code
1
VDD = 3V
0.8
0.6
0.6
0.4
0.4
0.2
0.2
0
–0.2
1
0
–0.4
–0.6
–0.6
–0.8
–0.8
–1
–1
512 1024 1536 2048 2560 3072 3584 4096
OUTPUT CODE
0
MAX INL
–0.4
–0.6
–1
0.8
512 1024 1536 2048 2560 3072 3584 4096
OUTPUT CODE
4000
2047 2048
CODE
2049
50.0
VDD = 3.6V
600
400
200
0
2050
0
50
150
100
200
SAMPLE RATE (ksps)
40.0
30.0
20.0
10.0
0.0
250
0
50
150
200
100
SAMPLE RATE (ksps)
236012 G14
236012 G13
124kHz Sine Wave 8192 FFT Plot
0
–71
VDD = 3.6V
–73
73
250
236012 G15
THD vs Input Frequency
SINAD vs Input Frequency
74
3.6
Reference Current vs Sample
Rate (TS8 Package)
2000
2046
1.6
2
2.4 2.8 3.2
REFERENCE VOLTAGE (V)
1.2
236012 G12
REFERENCE CURRENT (μA)
SUPPLY CURRENT (μA)
6000
MIN INL
MIN DNL
VDD = 3.6V
8000
VDD = 3V
fSMPL = 250ksps
–20
–75
–77
THD (dB)
VDD = 3.0V
72
VDD = 2.35V
71
VDD = 2.35V
–79
–81
–83
–85
70
MAGNITUDE (dB)
COUNT
0
–0.2
800
VDD = 3V
SINAD (dB)
0.2
Supply Current vs Sample Rate
10000
2045
MAX DNL
0.4
236012 G11
Histogram for 16384 Conversions
–40
–60
–80
–100
VDD = 3.6V
–87
–120
–89
69
0.6
–0.8
236012 G10
0
VDD = 3.6V
0.8
–0.2
–0.4
0
Integral and Differential Nonlinearity
vs Reference Voltage (TS8 Package)
VDD = 3V
0.8
DNL (LSB)
INL (LSB)
Differential Nonlinearity
vs Output Code
NONLINEARITY ERROR (LSB)
1
TA = 25°C, VDD = OVDD = VREF (LTC2361, Note 4)
1
10
100
INPUT FREQUENCY (kHz)
1000
2306012 G16
VDD = 3.0V
–91
1
10
100
INPUT FREQUENCY (kHz)
–140
1000
236012 G17
0
25
75
50
100
INPUT FREQUENCY (kHz)
125
2306012 G18
236012f
7
LTC2360/LTC2361/LTC2362
TYPICAL PERFORMANCE CHARACTERISTICS
Integral Nonlinearity
vs Output Code
1
VDD = 3V
0.8
0.6
0.6
0.4
0.4
0.2
0.2
DNL (LSB)
INL (LSB)
1
VDD = 3V
0
–0.2
0
–0.4
–0.6
–0.6
–0.8
–0.8
–1
–1
0.2
0
MIN INL
MIN DNL
–0.4
–0.6
–1
0.8
3.6
1.6
2
2.4 2.8 3.2
REFERENCE VOLTAGE (V)
1.2
236012 G21
Reference Current vs Sample
Rate (TS8 Package)
Supply Current vs Sample Rate
1200
10000
80.0
VDD = 3V
VDD = 3.6V
VDD = 3.6V
SUPPLY CURRENT (μA)
6000
4000
2000
REFERENCE CURRENT (μA)
1000
8000
800
600
400
60.0
40.0
20.0
200
0
2045
2046
2047 2048
CODE
2049
0
2050
0
100
300
200
400
SAMPLE RATE (ksps)
0.0
500
248kHz Sine Wave 8192 FFT Plot
–67
0
VDD = 3V
–20 fSMPL = 500ksps
VDD = 3.6V
MAGNITUDE (dB)
–71
VDD = 3.0V
–75
THD (dB)
VDD = 2.35V
72
71
VDD = 2.35V
–79
–83
70
VDD = 3.0V
VDD = 3.6V
–87
–91
1
10
100
INPUT FREQUENCY (kHz)
1000
2306012 G25
50 100 150 200 250 300 350 400 450 500
SAMPLE RATE (ksps)
236012 G24
THD vs Input Frequency
SINAD vs Input Frequency
74
73
0
236012 G23
236012 G22
SINAD (dB)
MAX INL
–0.2
236012 G20
Histogram for 16384 Conversions
69
MAX DNL
0.4
512 1024 1536 2048 2560 3072 3584 4096
OUTPUT CODE
236012 G19
COUNT
0.6
–0.8
0
512 1024 1536 2048 2560 3072 3584 4096
OUTPUT CODE
VDD = 3.6V
0.8
–0.2
–0.4
0
Integral and Differential Nonlinearity
vs Reference Voltage (TS8 Package)
Differential Nonlinearity
vs Output Code
NONLINEARITY ERROR (LSB)
1
0.8
TA = 25°C, VDD = OVDD = VREF (LTC2362, Note 4)
–40
–60
–80
–100
–120
1
10
100
INPUT FREQUENCY (kHz)
1000
2306012 G26
–140
0
50
150
100
200
INPUT FREQUENCY (kHz)
250
2306012 G27
236012f
8
LTC2360/LTC2361/LTC2362
PIN FUNCTIONS
S6 Package
TS8 Package
VDD (Pin 1): Positive Supply. The VDD range is 2.35V to
3.6V. VDD also defines the input span of the ADC, 0V to
VDD. Bypass to GND and to a solid ground plane with a
2.2μF ceramic capacitor (or 2.2μF tantalum in parallel
with 0.1μF ceramic).
VDD (Pin 1): Positive Supply. The VDD range is 2.35V to
3.6V. Bypass to GND and to a solid ground plane with a
2.2μF ceramic capacitor (or 2.2μF tantalum in parallel
with 0.1μF ceramic).
GND (Pin 2): Ground. The GND pin must be tied directly
to a solid ground plane.
AIN (Pin 3): Analog Input. AIN is a single-ended input with
respect to GND with a range from 0V to VDD.
SCK (Pin 4): Shift Clock Input. The SCK serial clock synchronizes the serial data transfer. SDO data transitions on
the falling edge of SCK.
SDO (Pin 5): Three-State Serial Data Output. The A/D
conversion result is shifted out on SDO as a serial data
stream with MSB first. The data stream consists of 12 bits
of conversion data followed by trailing zeros.
CONV (Pin 6): Convert Input. This active high signal starts
a conversion on the rising edge. The device automatically
powers down after conversion. A logic low on this input
enables the SDO pin, allowing the data to be shifted out.
VREF (Pin 2): Reference Input. VREF defines the input
span of the ADC, 0V to VREF. The VREF range is 1.4V to
VDD. Bypass to GND and to a solid ground plane with a
2.2μF ceramic capacitor (or 2.2μF tantalum in parallel
with 0.1μF ceramic).
GND (Pin 3): Ground. The GND pin must be tied directly
to a solid ground plane.
AIN (Pin 4): Analog Input. AIN is a single-ended input with
respect to GND with a range from 0V to VREF.
OVDD (Pin 5): Output Driver Supply for SDO. The OVDD
range is 1V to 3.6V. Bypass to GND and to a solid ground
plane with a 2.2μF ceramic capacitor (or 2.2μF tantalum in
parallel with 0.1μF ceramic). OVDD can be driven separately
from VDD and OVDD can be higher than VDD.
SDO (Pin 6): Three-State Serial Data Output. The A/D
conversion result is shifted out on SDO as a serial data
stream with MSB first. The data stream consists of 12 bits
of conversion data followed by trailing zeros.
SCK (Pin 7): Shift Clock Input. The SCK serial clock synchronizes the serial data transfer. SDO data transitions on
the falling edge of SCK.
CONV (Pin 8): Convert Input. This active high signal starts
a conversion on the rising edge. The device automatically
powers down after conversion. A logic low on this input
enables the SDO pin, allowing the data to be shifted out.
236012f
9
LTC2360/LTC2361/LTC2362
BLOCK DIAGRAM
2.2μF
2.2μF
+
+
1
ANALOG
INPUT
RANGE
0V TO VREF
5
VDD
OVDD
AIN
4
S AND H
THREE-STATE
SERIAL
OUTPUT
PORT
12-BIT ADC
SDO
6
VREF
2
2.2μF
SCK
TIMING
LOGIC
GND
3
CONV
7
8
TS8 PACKAGE
236012 BD
TIMING DIAGRAMS
t8
CONV
SDO
t7
1.6V
SCK
Hi-Z
SDO
236012 F01
1.6V
VIH
VIL
236012 F02
Figure 1. SDO Into Hi-Z State After CONV Rising Edge
Figure 2. SDO Data Valid Hold Time After SCK Falling Edge
t4
SCK
1.6V
VIH
SDO
VIL
236012 F03
Figure 3. SDO Data Valid Acess Time After SCK Falling Edge
236012f
10
LTC2360/LTC2361/LTC2362
APPLICATIONS INFORMATION
DC PERFORMANCE
DYNAMIC PERFORMANCE
The noise of an ADC can be evaluated in two ways: signal-to-noise ratio (SNR) in the frequency domain and
histogram in the time domain. The LTC2360/LTC2361/
LTC2362 excel in both. Figure 5 demonstrates that the
LTC2360/LTC2361/LTC2362 have an SNR of over 73dB.
The noise in the time domain histogram is the transition
noise associated with a 12-bit resolution ADC which can
be measured with a fixed DC signal applied to the input of
the ADC. The resulting output codes are collected over a
large number of conversions. The shape of the distribution of codes will give an indication of the magnitude of
the transition noise. In Figure 4, the distribution of output
codes is shown for a DC input that has been digitized
16384 times. The distribution is Gaussian and the RMS
code transition is about 0.32LSB. This corresponds to a
noise level of 73dB relative to a full scale of 3V.
The LTC2360/LTC2361/LTC2362 have excellent high speed
sampling capability. Fast fourier transform (FFT) test
techniques are used to test the ADCs’ frequency response,
distortion and noise at the rated throughput. By applying
a low distortion sine wave and analyzing the digital output
using an FFT algorithm, the ADCs’ spectral content can
be examined for frequencies outside the fundamental.
Figures 5 and 6 show typical LTC2361 and LTC2362 FFT
plots respectively.
10000
VDD = 3V
COUNT
8000
6000
4000
2000
0
2045
2046
2047 2048
CODE
2049
2050
236012 F04
Figure 4. Histogram for 16384 Conversions
0
–40
–60
–80
–40
–60
–80
–100
–100
–120
–120
–140
0
25
VDD = 3V
fSMPL = 500ksps
fIN = 248kHz
SINAD = 73dB
THD = –81dB
–20
MAGNITUDE (dB)
–20
MAGNITUDE (dB)
0
VDD = 3V
fSMPL = 250ksps
fIN = 124kHz
SINAD = 73dB
THD = –84dB
75
50
100
INPUT FREQUENCY (kHz)
125
236012 F05
Figure 5. LTC2361 FFT Plot
–140
0
50
150
100
200
INPUT FREQUENCY (kHz)
250
236012 F06
Figure 6. LTC2362 FFT Plot
236012f
11
LTC2360/LTC2361/LTC2362
APPLICATIONS INFORMATION
Signal-to-Noise plus Distortion Ratio
The signal-to-noise plus distortion ratio (SINAD) is the
ratio between the RMS amplitude of the fundamental
input frequency to the RMS amplitude of all other frequency components at the A/D output. The output is band
limited to frequencies from above DC and below half the
sampling frequency. Figure 6 shows a typical FFT with a
500kHz sampling rate and a 248kHz input. The dynamic
performance is excellent for input frequencies up to and
beyond the Nyquist frequency of 250kHz.
Effective Number of Bits
The effective number of bits (ENOB) is a measurement of
the resolution of an ADC and is directly related to SINAD
by the equation:
ENOB =
SINAD – 1.76
6.02
where ENOB is the effective number of bits of resolution
and SINAD is expressed in dB. At the maximum sampling
74
rate of 500kHz, the LTC2362 maintains ENOB above 11
bits up to the Nyquist input frequency of 250kHz (refer
to Figure 7).
Total Harmonic Distortion
The total harmonic distortion (THD) is the ratio of the RMS
sum of all harmonics of the input signal to the fundamental
itself. The out-of-band harmonics alias into the frequency
band between DC and half the sampling frequency. THD
is expressed as:
THD = 20log
V2 2 + V3 2 + V4 2 + ...Vn 2
V1
where V1 is the RMS amplitude of the fundamental
frequency and V2 through Vn are the amplitudes of the
second through nth harmonics. THD vs. Input Frequency
is shown in Figure 8. The LTC2362 has excellent distortion
performance up to the Nyquist frequency and beyond.
–67
12
VDD = 3.6V
73
11.67
71
70
11.34
–75
ENOB
VDD = 2.35V
VDD = 2.35V
–79
–83
69
68
67
THD (dB)
72
SINAD (dB)
–71
VDD = 3.0V
11
1
10
100
INPUT FREQUENCY (kHz)
1000
2306012 F07
Figure 7. LTC2362 ENOB and SINAD vs Input Frequency
VDD = 3.0V
VDD = 3.6V
–87
–91
1
10
100
INPUT FREQUENCY (kHz)
1000
2306012 F08
Figure 8. LTC2362 THD vs Input Frequency
236012f
12
LTC2360/LTC2361/LTC2362
APPLICATIONS INFORMATION
Intermodulation Distortion
Peak Harmonic or Spurious Noise
If the ADC input signal consists of more than one spectral
component, the ADC transfer function nonlinearity can
produce intermoduation distortion (IMD) in addition to
THD. IMD is the change in one sinusoidal input caused
by the presence of another sinusoidal input at a different
frequency.
The peak harmonic or spurious noise is the largest spectral
component excluding the input signal and DC. This value
is expressed in decibels relative to the RMS value of a
full-scale input signal.
If two pure sine waves of frequencies fa and fb are applied
to the ADC input, nonlinearities in the ADC transfer function
can create distortion products at the sum and difference
frequencies of mfa ± nfb, where m and n = 0, 1, 2, 3, etc.
For example, the 2nd order IMD terms include (fa ± fb).
If the two input sine waves are equal in magnitude, the
value (in decibels) of the 2nd order IMD products can be
expressed by the following formula:
The full-power bandwidth is that input frequency at which
the amplitude of reconstructed fundamental is reduced by
3dB for full-scale input signal.
Amplitude at ( fa ± fb )
Amplitude at fa
The full-linear bandwidth is the input frequency at which the
SINAD has dropped to 68dB (11 effective bits). The LTC2362
has been designed to optimize input bandwidth, allowing the
ADC to undersample input signals with frequencies above
the converter’s Nyquist frequency. The noise floor stays
very low at high frequencies; SINAD becomes dominated
by distortion at frequencies far beyond Nyquist.
0
VDD = 3.6V
fSMPL = 500ksps
fa = 99kHz
fb = 101kHz
IMD = –76.5dB
–20
MAGNITUDE (dB)
IMD ( fa ± fb ) = 20log
Full-Power and Full-Linear Bandwidth
–40
–60
–80
–100
–120
0
50
100
200
150
INPUT FREQUENCY (kHz)
250
236012 F09
Figure 9. LTC2362 Intermodulation Distortion Plot
236012f
13
LTC2360/LTC2361/LTC2362
APPLICATIONS INFORMATION
OVERVIEW
Data Transfer
The LTC2360/LTC2361/LTC2362 use a successive approximation algorithm and internal sample-and-hold circuit
to convert an analog signal to a 12-bit serial output. All
devices operate from a single 2.35V to 3.6V supply. The
conversion time of the devices is controlled by an internal
oscillator, which allows the LTC2360/LTC2361/LTC2362
to sample at a rate of 100ksps, 250ksps and 500ksps
respectively.
A rising CONV edge starts a conversion and disables SDO.
After the conversion, the ADC automatically goes into sleep
mode, drawing only leakage current.
The LTC2360/LTC2361/LTC2362 contain a 12-bit, switchedcapacitor ADC, a sample-and-hold, a serial interface(see
Block Diagram) and are available in tiny 6- or 8-lead
TSOT-23 packages.
The S6 package of the LTC2360/LTC2361/LTC2362 uses
VDD as the reference and has an analog input range of 0V
to VDD. The ADC samples the analog input with respect to
GND and outputs the result through the serial interface.
The TS8 package provides two additional pins: a reference
pin, VREF, and an output supply pin, OVDD. The ADC can
operate with reduced spans down to 1.4V and achieve
342μV resolution. OVDD controls the output swing of the
digital output pin, SDO, and allows the device to communicate with 1.8V, 2.5V or 3V digital systems.
SERIAL INTERFACE
The LTC2360/LTC2361/LTC2362 communicate with microcontrollers, DSPs and other external circuitry via a 3-wire
interface. Figure 10 shows the operating sequence of the
serial interface.
CONV going low enables SDO and clocks out the MSB bit,
B11. SCK then synchronizes the data transfer with each
bit being transmitted on the falling SCK edge and can be
captured on the rising SCK edge. After completing the
data transfer, if further SCK clocks are applied with CONV
low, SDO will output zeros indefinitely (see Figure 10). For
example, 16-clocks at SCK will produce the 12-bit data
and four trailing zeros on SDO.
SLEEP MODE
The LTC2360/LTC2361/LTC2362 enter sleep mode to save
power after each conversion if CONV remains high. In sleep
mode, all bias currents are shut down and only leakage
currents remain (about 0.1μA). The sample-and-hold is
in hold mode while the ADC is in sleep mode. The ADC
returns to sample mode after the falling edge of CONV
during power-up (see Figure 10).
Exiting Sleep Mode and Power-Up Time
By taking CONV low, the ADC powers up and acquires an
input signal completely after the aquisition time (tACQ).
After tACQ, the ADC can perform a conversion as described
in the Serial Interface section (see Figure 10).
BY TAKING CONV LOW, THE DEVICE POWERS UP
AND ACQUIRES AN INPUT ACCURATELY AFTER tACQ
CONV
tCONV
SCK
SDO
SLEEP MODE
RECOMMENDED HIGH OR LOW
Hi-Z STATE
t2
t6
1
t3
B11
2
3
4
t4
B10
9
10
t5
B9
12
t7
B3
B2
t8
B1
B0*
236012 F10
(MSB)
t1
11
tACQ
tTHROUGHPUT
*AFTER COMPLETING THE DATA TRANSFER, IF FURTHER SCK CLOCKS ARE
APPLIED WITH CONV LOW, THE ADC WILL OUTPUT ZEROS INDEFINITELY
Figure 10. LTC2360/LTC2361/LTC2362 Serial Interface Timing Diagram
236012f
14
LTC2360/LTC2361/LTC2362
APPLICATIONS INFORMATION
ACHIEVING MICROPOWER PERFORMANCE
With typical operating currents of 0.5mA, 0.75mA and
1.1mA for the LTC2360/LTC2361/LTC2362 and automatically entering sleep mode right after a conversion, these
devices achieve extremely low power consumption over
a wide range of sample rates (see Figure 11). The sleep
mode allows the supply current to drop with reduced
sample rate. Several things must be taken into account
to achieve such low power consumption.
Minimize Power Consumption in Sleep Mode
The LTC2360/LTC2361/LTC2362 enter sleep mode after
each conversion if CONV remains high and draw only
leakage current (see Figure 10). If the CONV input is not
running rail-to-rail, the input logic buffer will draw current.
This current may be large compared to the typical supply
1200
VDD = OVDD = VREF = 3.6V
TA = 25°C
current. To obtain the lowest supply current, bring the CONV
pin to GND when it is low and to VDD when it is high.
After the conversion with CONV staying high, the converter
is in sleep mode and draws only leakage current. The status
of the SCK input has no effect on supply current during
this time. For the best performance, hold SCK either high
or low while the ADC is converting.
Minimize the Device Active Time
In systems that have significant time between conversions,
the ADC draws a minimal amount of power. Figures 12
and 13 show two ways to minimize the amount of time
the ADC draws power. In Figure 12, the ADC draws power
during tACQ and tCONV and is in sleep mode for the rest of
the time. The conversion results are available at the next
CONV falling edge. In Figure 13, the ADC draws twice the
power than that in Figure 12, but the conversion results
are available during tDATA. The user can use the fastest
SCK available in the system to shorten data transfer time,
tDATA as long as t4 and t7 are not violated.
SUPPLY CURRENT (μA)
1000
SDO Loading
800
Capacitive loading on the digital output can increase power
consumption. A 100pF capacitor on the SDO pin can add
more than 50μA to the supply current at a 200kHz clock
frequency. An extra 50μA or so of current goes into charging and discharging the load capacitor. The same goes for
digital lines driven at a high frequency by any logic. The
C • V • f currents must be evaluated with the troublesome
ones minimized.
LTC2361
600
LTC2362
400
LTC2360
200
0
1
10
100
SAMPLE RATE (ksps)
1000
236012 TA01b
Figure 11. Supply Current vs Sample Rate
EXECUTING A CONVERSION AND PUTTING
THE DEVICE INTO SLEEP MODE
SAMPLING INPUT AND
TRANSFERRING DATA
CONV
tACQ
tCONV
RECOMMENDED HIGH OR LOW
SCK
SDO
SLEEP MODE
1
2
B11
B10
3
B9
4
9
B3
10
B2
11
B1
12
B0
Hi-Z STATE
tTHROUGHPUT = tACQ + tCONV + tSLEEPMODE
236012 F12
Figure 12. Minimize the Time When the Device Draws Power, While the Conversion Results are Available After the Device Wakes Up
236012f
15
LTC2360/LTC2361/LTC2362
APPLICATIONS INFORMATION
CONV
EXECUTE CONVERSION
DATA TRANSFER
ACQUIRE
INPUT
tACQ
SCK
tCONV
EXECUTING A DUMMY CONVERSION AND
PUT THE DEVICE INTO SLEEP MODE
tDATA
tCONV
RECOMMENDED HIGH OR LOW
SDO
SLEEP MODE
RECOMMENDED HIGH OR LOW
1
2
B11
B10
3
B9
4
9
B3
10
B2
11
B1
12
B0
tTHROUGHPUT = tACQ + 2 • tCONV + tDATA + tSLEEPMODE
Hi-Z STATE
236012 F13
Figure 13. Minimize the Time When the Device Draws Power, While the Conversion Results are Available Right After Conversion
SINGLE-ENDED ANALOG INPUT
Driving the Analog Input
The analog input of the LTC2360/LTC2361/LTC2362 is
easy to drive. The input draws only one small current
spike while charging the sample-and-hold capacitor with
the ADC going into track mode. During the conversion,
the analog input draws only a small leakage current. If
the source impedance of the driving circuit is low, then
the input of the LTC2360/LTC2361/LTC2362 can be driven
directly. As source impedance increases, so will acquisition time. For minimum acquisition time with high source
impedance, a buffer amplifier should be used. The main
requirement is that the amplifier driving the analog input
must settle after the small current spike before the next
conversion starts (settling time must be less than tACQ
for full throughput rate). While choosing an input amplifier, also keep in mind the amount of noise and harmonic
distortion the amplifier contributes.
Choosing an Input Amplifier
Choosing an input amplifier is easy if a few requirements
are taken into consideration. First, to limit the magnitude
of the voltage spike seen by the amplifier from charging
the sampling capacitor, choose an amplifier that has a low
output impedance (<100Ω) at the closed-loop bandwidth
frequency. For example, if an amplifier is used in a gain
of 1 and has a unity-gain bandwidth of 10MHz, then the
output impedance at 10MHz must be less than 100Ω. The
second requirement is that the closed-loop bandwidth must
be greater than 8MHz to ensure adequate small-signal
settling for full throughput rate. If slower op amps are
used, more time for settling can be provided by increasing
the time between conversions. The best choice for an op
amp to drive the LTC2360/LTC2361/LTC2362 will depend
on the application. Generally, applications fall into two
categories: AC applications where dynamic specifications
are most critical and time domain applications where DC
accuracy and settling time are most critical. The following list is a summary of the op amps that are suitable for
driving the LTC2360/LTC2361/LTC2362. (More detailed
information is available on the Linear Technology website at
www.linear.com.)
LTC1566-1: Low Noise 2.3MHz Continuous Time Lowpass Filter.
LT®1630: Dual 30MHz Rail-to-Rail Voltage FB Amplifier.
2.7V to ±15V supplies. Very high AVOL, 500μV offset and
520ns settling to 0.5LSB for a 4V swing. THD and noise
are –93dB to 40kHz and below 1LSB to 320kHz (AV =
1, 2VP-P into 1k, VS = 5V), making the part excellent for
AC applications (to 1/3 Nyquist) where rail-to-rail performance is desired. Quad version is available as LT1631.
LTC6241: Dual 18MHz, Low Noise, Rail-to-Rail, CMOS
Voltage FB Amplifier. 2.8V to 6V supplies. Very high AVOL
and 125μV offset. It is suitable for applications with a single
5V supply. Quad version is available as LTC6242.
LT1797: Unity-Gain Stable 10MHz, Rail-to-Rail Voltage
Feedback Amplifier.
LT1801: 180MHz GBWP, –75dBc at 500kHz, 2mA/Amplifier, 8.5nV/√Hz.
LT6203: 100MHz GBWP, –80dBc Distortion at 1MHz, UnityGain Stable, R-R In and Out, 3mA/Amplifier, 1.9nV/√Hz.
236012f
16
LTC2360/LTC2361/LTC2362
APPLICATIONS INFORMATION
Input Filtering and Source Impedance
Reference Input
The noise and the distortion of the input amplifier and
other circuitry must be considered since they will add to
the LTC2360/LTC2361/LTC2362 noise and distortion. The
small-signal bandwidth of the sample-and-hold circuit is
10MHz. Any noise or distortion products that are present at the analog inputs will be summed over this entire
bandwidth. Noisy input circuitry should be filtered prior
to the analog inputs to minimize noise. A simple 1-pole
RC filter is sufficient for many applications. For example,
Figure 14 shows a 220pF capacitor from AIN to ground
and a 51Ω source resistor to limit the input bandwidth
to 10MHz. The 220pF capacitor also acts as a charge
reservoir for the input sample-and-hold and isolates the
ADC input from sampling-glitch sensitive circuitry. High
quality capacitors and resistors should be used since these
components can add distortion. NPO and silvermica type
dielectric capacitors have excellent linearity. Carbon surface
mount resistors can generate distortion from self heating
and from damage that may occur during soldering. Metal
film surface mount resistors are much less susceptible to
both problems. When high amplitude unwanted signals
are close in frequency to the desired signal frequency,
a multiple pole filter is required. High external source
resistance, combined with the 20pF of input capacitance,
will reduce the rated 10MHz bandwidth and increase
acquisition time beyond 500ns.
On the TS8 package of the LTC2360/LTC2361/LTC2362,
the voltage on the VREF pin defines the full-scale range
of the ADC. The reference voltage can range from VDD
down to 1.4V.
Input Range
The analog input of the LTC2360/LTC2361/LTC2362 is
driven single-ended with respect to GND from a single
supply. The input may swing up to VDD for the S6 package
and to VREF for the TS8 package. The 0V to 2.5V range is
also ideally suited for single-ended input use with VDD or
VREF = 2.5V for single supply applications. If the difference
between the AIN input and GND exceeds VDD for the S6
package or VREF for the TS8 package, the output code will
stay fixed at all ones, and if this difference goes below 0V,
the output code will stay fixed at all zeros.
Figure 15 shows the ideal input/output characteristics for
the LTC2360/LTC2361/LTC2362. The code transitions occur midway between successive integer LSB values (i.e.,
0.5LSB, 1.5LSB, 2.5LSB, …, FS – 1.5LSB). The output
code is straight binary with 1LSB = VDD/4096 for the S6
package and 1LSB = VREF /4096 for the TS8 package.
111...111
LTC2362
1
2.2μF
220pF
51Ω
2
3
VDD
CONV
GND
SDO
AIN
SCK
6
5
4
236012 F14
UNIPOLAR OUTPUT CODE
111...110
000...001
000...000
Figure 14. RC Input Filter
0
1LSB
INPUT VOLTAGE (V)
FS – 1LSB
236012 F15
Figure 15. Transfer Characteristics
236012f
17
LTC2360/LTC2361/LTC2362
APPLICATIONS INFORMATION
BOARD LAYOUT AND BYPASSING
connecting the pins and the bypass capacitors must be
kept short and should be made as wide as possible.
Wire wrap boards are not recommended for high resolution
and/or high speed A/D converters. To obtain the best performance from the LTC2360/LTC2361/LTC2362, a printed
circuit board with ground plane is required. Layout for the
printed circuit board should ensure that digital and analog
signal lines are separated as much as possible. In particular,
care should be taken not to run any digital track alongside
an analog signal track or underneath the ADC. The analog
input should be screened by the ground plane.
Figure 16 shows the recommended system ground connections. All analog circuitry grounds should be terminated
at the LTC2360/LTC2361/LTC2362. The ground return
from the LTC2360/LTC2361/LTC2362 to the power supply
should be low impedance for noise free operation. Digital
circuitry grounds must be connected to the digital supply
common.
In applications where the ADC data outputs and control signals are connected to a continuously active microprocessor
bus, it is possible to get errors in the conversion results.
These errors are due to feedthrough from the microprocessor to the successive approximation comparator. The
problem can be eliminated by forcing the microprocessor
into a wait state during conversion or by using three-state
buffers to isolate the ADC data bus.
High quality tantalum and ceramic bypass capacitors
should be used at the VDD pin as shown in the Block
Diagram on the first page of this data sheet. For optimum
performance, a 2.2μF surface mount AVX capacitor with
a 0.1μF ceramic is recommended for the VDD and VREF
pins. Alternatively, 2.2μF ceramic chip capacitors such as
Murata GRM235Y5V106Z016 may be used. The capacitors
must be located as close to the pins as possible. The traces
CVDD
+
2.2μF
PIN 1
CAIN
VDD
CONV
GND
SDO
AIN
SCK
VIAS TO GROUND PLANE
236012 F16
Figure 16. Power Supply Ground Practice
236012f
18
LTC2360/LTC2361/LTC2362
PACKAGE DESCRIPTION
S6 Package
6-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1636)
0.62
MAX
2.90 BSC
(NOTE 4)
0.95
REF
1.22 REF
2.80 BSC
1.4 MIN
3.85 MAX 2.62 REF
1.50 – 1.75
(NOTE 4)
PIN ONE ID
RECOMMENDED SOLDER PAD LAYOUT
PER IPC CALCULATOR
0.30 – 0.45
6 PLCS (NOTE 3)
0.95 BSC
0.80 – 0.90
0.20 BSC
0.01 – 0.10
1.00 MAX
DATUM ‘A’
0.30 – 0.50 REF
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DRAWING NOT TO SCALE
3. DIMENSIONS ARE INCLUSIVE OF PLATING
1.90 BSC
0.09 – 0.20
(NOTE 3)
S6 TSOT-23 0302 REV B
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
5. MOLD FLASH SHALL NOT EXCEED 0.254mm
6. JEDEC PACKAGE REFERENCE IS MO-193
TS8 Package
8-Lead Plastic TSOT-23
(Reference LTC DWG # 05-08-1637)
0.52
MAX
2.90 BSC
(NOTE 4)
0.65
REF
1.22 REF
1.4 MIN
3.85 MAX 2.62 REF
2.80 BSC
1.50 – 1.75
(NOTE 4)
PIN ONE ID
RECOMMENDED SOLDER PAD LAYOUT
PER IPC CALCULATOR
0.22 – 0.36
8 PLCS (NOTE 3)
0.65 BSC
0.80 – 0.90
0.20 BSC
0.01 – 0.10
1.00 MAX
DATUM ‘A’
0.30 – 0.50 REF
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. DRAWING NOT TO SCALE
3. DIMENSIONS ARE INCLUSIVE OF PLATING
0.09 – 0.20
(NOTE 3)
1.95 BSC
TS8 TSOT-23 0802
4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR
5. MOLD FLASH SHALL NOT EXCEED 0.254mm
6. JEDEC PACKAGE REFERENCE IS MO-193
236012f
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
19
LTC2360/LTC2361/LTC2362
TYPICAL APPLICATION
Recommended AC Test Circuitry for the LTC2362
3V
+
+
4.7μF
2.2μF
1k
1%
±1.5V AC INPUT
VDD
50Ω
5%
4.7μF
CONV
AIN
LTC2362
220pF
2200pF
SCK
TO
MCU
SDO
GND
1k
1%
236012 TA02
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LTC1403/LTC1403A
12-/14-Bit, 2.8Msps Serial Sampling ADC
3V, Differential Input, 12mW, MSOP Package
LTC1407/LTC1407A
12-/14-Bit, 3Msps Simultaneous Sampling ADC
3V, 2-Channel Differential, 14mW, MSOP Package
LTC1860
12-Bit, 250ksps Serial ADC
5V Supply, 1-Channel, 4.3mW, MSOP-8 Package
LTC1860L
12-Bit, 150ksps Serial ADC
3V Supply, 1-Channel, 1.3mW, MSOP-8 Package
LTC1861
12-Bit, 250ksps Serial ADC
5V Supply, 2-Channel, 4.3mW, MSOP-8 Package
LTC1861L
12-Bit, 150ksps Serial ADC
3V Supply, 2-Channel, 1.3mW, MSOP-8 Package
LTC1863
12-Bit, 200ksps Serial ADC 8-Channel ADC
5V Supply, 6.5mW, SSOP-16 Package, Pin Compatible to LTC1863L,
LTC1867
LTC1863L
12-Bit, 250ksps Serial ADC 8-Channel ADC
5V Supply, 2.2mW, SSOP-16 Package, Pin Compatible to LTC1863,
LTC1867L
LTC1864/LTC1865
16-Bit, 250ksps Serial ADC
5V Supply, 1 and 2 Channel, 4.3mW, MSOP Package
LTC1867
16-Bit, 200ksps Serial ADC 8-Channel ADC
5V Supply, 6.5mW, SSOP-16 Package, Pin Compatible to LTC1863,
LTC1867L
LTC1867L
16-Bit, 175ksps Serial ADC 8-Channel ADC
3V Supply, 2.2mW, SSOP-16 Package, Pin Compatible to LTC1863L,
LTC1867
LTC2355/LTC2356
12-/14-Bit, 3.5Msps Serial ADCs
3.3V Supply, Differential Input, 18mW, MSOP Package
LTC2365/LTC2366
12-Bit, 1/3 Msps Serial ADCs in TSOT23
2.35V to 3.6V Supply, Pin and Software Compatible to
LTC2360/LTC2361/LTC2362
16-Bit, Serial SoftSpan™ IOUT DAC
±1LSB INL/DNL, Software Selectable Spans
ADCs
DACs
LTC1592
LTC1666/LTC1667/LTC1668 12-/14-/16-Bit, 50Msps DACs
87dB SFDR, 20ns Settling Time
12-/10-/8-Bit Single VOUT DACs
SC70 6-Pin Package, Internal Reference, ±1LSB INL (12 Bits)
LT1460-2.5
Micropower Series Voltage Reference
0.1% Initial Accuracy, 10ppm Drift
LT1461-2.5
Precision Voltage Reference
0.05% Initial Accuracy, 3ppm Drift
LT1790-2.5
Micropower Series Reference in SOT-23
0.05% Initial Accuracy, 10ppm Drift
LT6660
Ultra-Tiny Micropower Series Reference
2mm × 2mm DFN Package, 0.2% Initial Accuracy, 10ppm Drift
LTC2630
References
SoftSpan is a trademark of Linear Technology Corporation.
236012f
20 Linear Technology Corporation
LT 0408 • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900
●
FAX: (408) 434-0507 ● www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2008