ACTIVE SIGNAL AMPLIFIER Vin&Iout T51/52/61/62_D/S DESCRIPTION The series is PRODUCT PROGRAM a high integration, efficiency polygonal – line active isolation Part Number Input Output Isolation Power Output Channels amplifier module, with anterior circuit voltage T5150D/S 12V 0-10V 4-20mA NONE 1 signal input and posterior current signal output. These modules a high T5230D/S 24V 0-10V 0-20mA NONE 1 T6130D/S 24V 0-5V 4-20mA NONE 1 efficiency isolated micro-power source, which T6135D/S 24V 0-5V 4-20mA 12V 1 T6230D/S 24V 0-5V 0-20mA NONE 1 applications, our products largely predigest T6233D/S 24V 0-5V 0-20mA 24V 1 customers’ design helpfully improve the using T6235D/S 24V 0-5V 0-20mA 12V 1 room ratio of PCB .Adopting electromagnetism T6250D/S 12V 0-5V 0-20mA NONE 1 isolation technology, it is available to keep high T6253D/S 12V 0-5V 0-20mA 24V 1 T6255D/S 12V 0-5V 0-20mA 12V 1 are embed with high can provide a electrics-feed for signal input. In the two-wire three-wire and four-wire circuit accuracy and natural extremely low temperature drift. The isolation voltage among the input, output power supply and isolated power output can up to 2.5KVDC. Power Supply Note: We could also offer customer design for special input and output. ELECTRICAL CHARACTERISTICS Power Supply Data FEATURES ● Three-port isolation（Among input, output and power supply） Isolation Power Output Data ● High accuracy (0.1% F.S.) ● High linearity (0.1% F.S.) Input Data ● Isolation voltage(2500VDC/60S) ● High frequency response(15KHz) ● Extremely low temperature(35PPM/℃ ) Output Data ● Industry standard(Operating Temperature Range:-25°C to 71°C) ● High reliability(MTBF＞500,000 hours) TXXXXD Pa ckage style Iso lation po w er o utpu t Pow e r supp ly Out put Inp ut Isolatio n Amp lifier MORNSUN Science & Technology co.,Ltd. Address: 2th floor 6th building, Huangzhou Industrial District, Guangzhou, China Tel: 86-20-38601850 Fax:86-20-38601272 Http://www.mornsun-power.com (Nominal Power Supply)±5% Power Dissipation ≤2W Power Protection Reverse protection Output Voltage (Nominal) ±10% Output Current ≤25mA Input Signal See above Input Impedance ≥10MΩ Overload ≤30V Output Signal See above Load ≤500Ω（At output=20mA） TRANSMISSION CHARACTERISTICS Offset MODEL SELECTION Power Supply 0.1%F.S. Gain Error 0.1%F.S. Temperature Drift 0.0035%F.S./℃ (-25℃ to +71 ℃) ISOLATION CHARACTERISTICS Galvanic Isolation Three-port isolation（Among input, output and power supply） Isolation Voltage 2.5KVDC (Tested for 1minute and 1mA max, humidity < 70%) Insulation Resistance 1000MΩ, 500VDC (Among signal input, signal output and power supply) OTHER CHARACTERISTICS Ambient temperature Operation temperature:-25℃ to +71℃ Package DIP24/SOIC24 Weight About 10g The Environment in use No dusts, gases of fiercely vibration, impulsion or gases that may erode to the components surrounded Transport and Storage temperature:-50℃ to +105℃ Note: 1. All specifications measured at TA=25°C, humidity<75%, nominal input voltage and rated output load unless otherwise specified. 2. Only typical models listed, specifications of custom product may be different. Please contact our service people directly for certain conditions. The copyright and authority for the interpretation of the products are reserved by Mornsun Specifications subject to change without notice. T51/52/61/62_D/S A/3-2008 Page 1 of 2 SCHEMATIC DIAGRAM APPLICATION NOTE 1. Please read instruction book carefully before 24Power su pply 23+ using the product. If you have any question, please contact with our technical support. 13Isolation Power Output 14+ 2. Please don’t install in the dangerous zone. 3. The power supply is direct voltage. 220V alternating current is forbidden.. Iou t+ Vin12Signal input 11+ Vin+ 2+ Signal ou tput 4. Don’t divide the product privately in case the equipments ineffective or go wrong. 1- Iout- AFTER SERVICE 1. Products are carefully inspected and controlled APPLICATION CIRCUIT DIAGRAM before going out from our factory. If they operated abnorm ally or there were som ething Power Supply Isolation Power Output wrong in the inner parts, please contact with our 16 15 14 13 PinPin+ NC NC NC NC NC PoutPout+ agents near you or technical support in our 24 23 22 21 20 company as soon as possible. 2. 3 years warranty since the delivery date. During the period of NC NC Sin+ Sin- quality guarantee，our company SoutSout+ NC NC NC TxxxxD will repair or change free of charge if product has 1 2 3 4 5 9 10 11 12 any quality problem in the process of normally using. Input Output APPLICATION CIRCUITS See A GUIDE TO INSTRUMENTATION ISOLATION AMPLIFIERS for more detail. PACKAGING SIZE AND TERMINAL DESCRIPTION First Angle Projection SOIC Package 0.70 (0.028) 4.00 (0.157) 27.94(1.100) 32.30(1.272) 14.40 (0.560) 14.40 (0.560) 18.60(0.732) 32.30(1.272) 0.65 (0.026) 10.20 (0.397) 10.20 (0.397) DIP Package RECOMMENDED FOOTPRINT Top view,grid:2.54mm(0.1inch) diameter:1.00mm(0.039inch) (0.028) 1.15±0.15 16 15 1413 2423222120 2.00 (0.079) Vin- 19.24(0.757) 24 23 2221 20 1 2 3 4 5 16151413 Vin- 0.30 (0.012) 1 2 3 4 5 9 1011 12 9 101112 1.00 (0.039) FOOTPRINT DETAILS P IN FUNCTION PIN OutputOutput+ Input+ FUNCTION Isolation Power Output+ Power Supply+ 24(Vin-) Others Power SupplyNC Isolation Power OutputNC:No Connection Note: Unit:mm(inch) Pin section:0.50*0.30mm(0.020*0.012inch) Pin tolerances:±0.10mm(±0.004inch) General tolerances:±0.25mm(±0.010inch) The copyright and authority for the interpretation of the products are reserved by Mornsun Specifications subject to change without notice. T51/52/61/62_D/S A/3-2008 Page 2 of 2