Ultra-Miniature Slides Series SS Distinctive Characteristics Top or side actuation permits flexible board design. Bright, LED illumination at tip of actuator. Compact dimensions and low profile allow high density mounting and close stacking of PC boards. Crisp actuation positively indicates circuit status. Double molded thermoset base and thermoplastic housing prevent loosening of terminals due to high soldering temperatures. Sliding twin contact mechanism with self-cleaning action provides smooth actuation and produces high contact reliability. Insert molded terminals lock out flux, solvents, and other contaminants. Inch terminal spacing for standard PC board grid (.100” x .100”). Actual Size NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 07-07 Ultra-Miniature Slides Series SS General Specifications Electrical Capacity (Resistive Load) Power Level: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Contact Timing: Total Travel: Materials & Finishes Actuator: Upper Case: Lower Case: Movable Contactor: Interior Base: Terminals: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: PCB Processing Soldering: Cleaning: 0.1A @ 30V DC 20 milliohms maximum 100 megohms minimum @ 500V DC 500V AC minimum 1 minute minimum 10,000 operations minimum 10,000 operations minimum Shorting (make-before-break) .079” (2.0mm) Polyacetal Polyacetal Glass fiber reinforced polyester Phosphor bronze with silver plating Phenolic resin (thermoset) Brass with silver plating over copper plating –15°C through +60°C (+5°F through +140°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering: See Profile B in Supplement section. Manual Soldering: See Profile B in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications UL Recognition or CSA Certification: The SS series devices have not been tested for UL recognition and CSA certification. These switches are designed for se in a low-voltage, low-current circuit. When used as intended in a low-voltage, low-current circuit, the results do not produce hazardous energy. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 07-07 Series SS Ultra-Miniature Slides TYPICAL SWITCH ORDERING EXAMPLE SS 12S D P POLES & CIRCUITS 2 L C LED COLORS ACTUATION 12S SPDT ON NONE ON P Top Actuated C Red 22S DPDT ON NONE ON H Side Actuated E Yellow F Green TERMINAL SPACING D CONTACT MATERIAL & RATINGS Inch .100” x .100” LED CIRCUIT L Isolated Silver Rated 0.1A @ 30V DC 2 DESCRIPTION FOR TYPICAL ORDERING EXAMPLE SS12SDP2LC Red LED Top Actuated SPDT ON-NONE-ON Circuit Silver Contacts Rated 0.1A @ 30V DC Terminals with .100” Spacing POLES & CIRCUITS Slide Position Pole Model SP SS12S Connected Terminals Right Center Left Right Center Left ON NONE ON 2-1 OPEN 2-3 Throw & Schematics Note: Terminal numbers are not actually on switch. Isolated LED circuit requires external power source. SPDT 1 DP SS22S ON NONE ON 2-1 5-4 OPEN 2-3 5-6 2 (COM) DPDT 1 2 (COM) 3 4 (+) (-) (+) (-) 3 5 (COM) 6 TERMINAL SPACING D Inch .100” x .100” Single Pole Models (0.4) Typ .016 (2.54) Typ .100 (3.4) Typ .134 (9.0) .354 (0.4) Typ .016 (2.54) Typ .100 (0.6) Typ .024 (13.0) .512 (2.54) Typ .100 (3.4) Typ .134 Double Pole Models (9.0) .354 (2.54) Typ .100 (0.6) Typ .024 (13.0) .512 NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 07-07 Series SS Ultra-Miniature Slides CONTACT MATERIALS & RATINGS 2 Silver over Phosphor Bronze Power Level 0.1A @ 30V DC TYPICAL SWITCH DIMENSIONS Top Actuated Single & Double Pole (2.54) .100 L (+) (2.0) Travel .079 (0.4) .016 (2.54) .100 (0.6) Typ .024 (0.3) Typ .012 3 (3.7) .146 (9.0) .354 (0.3) Typ .012 1 (13.0) .512 L (-) (2.54) Typ .100 (3.0) .118 (2.5) .098 (2.5) .098 2 (2.54) Typ .100 L (+) 1 2 L (+) 3 L (-) L (-) (13.0) .512 6 (2.54) Typ .100 (0.6) Typ .024 (0.4) Typ .016 4 L (+) 1 5 2 6 L (-) 3 (2.54) Typ .100 (0.8) Dia Typ .031 SS22SDP2LC Side Actuated (2.54) Typ .100 3 (0.8) Dia Typ .031 4 5 2 (0.6) Typ .024 (0.4) Typ .016 (4.5) .177 1 Single & Double Pole (2.54) .100 L (+) (2.0) Travel .079 (3.7) .146 (2.54) .100 (0.6) Typ .024 (0.4) .016 1 L (+) 1 (13.0) .512 2 3 (2.5) .098 L (+) 3 L (-) 2 L (-) (13.0) .512 6 (2.54) Typ .100 3 (0.8) Dia Typ .031 4 5 2 1 (2.54) Typ .100 (2.54) Typ .100 (0.6) Typ .024 (0.4) Typ .016 (4.85) .191 (7.5) .295 L (-) (0.4) Typ (0.3) Typ .016 .012 (2.54) Typ .100 (0.3) Typ .012 (7.5) .295 (2.5) .098 (3.0) .118 (0.6) Typ .024 (4.5) .177 (9.0) .354 4 L (+) 1 5 2 6 L (-) 3 (2.54) Typ .100 (0.8) Dia Typ .031 SS12SDH2LC LED COLORS & SPECIFICATIONS LEDs are supplied as an integral part of the switch (not available separately). The lamp circuit is independent of switch operation. Electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula given in the Supplement. L Isolated, 1-element (+) (-) Color C E Red Yellow F Green Forward Peak Current IFM 30mA 30mA 25mA Continuous Forward Current IF 16mA 16mA 16mA Forward Voltage VF 1.98V 2.06V 2.16V Reverse Peak Voltage VRM 5V 5V 5V Current Reduction Rate Above 25°C ∆IF 0.40mA/°C 0.42mA/°C 0.33mA/°C Ambient Temperature Range –15° ~ +60°C OPTIONAL CAP AT4065 Slide Cap Material: Polycarbonate Cap can be assembled on request Cap Color: Black only (3.2) .126 (5.0) .197 (5.0) .197 (11.0) .433 (8.5) .335 (0.6) .024 Window color should match LED color. Colors Available: C Red E Yellow F Green NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 07-07