PM25CLB120 Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 Intellimod™ L-Series Three Phase IGBT Inverter 25 Amperes/1200 Volts A D E F G L AB (4 PLACES) H J K J J K K V V TERMINAL CODE M 1 VUPC K 2 UFO 3 UP 4 VUP1 N Y 5 VVPC W 6 VFO 7 VP X B AA Y 1 V V 5 9 13 P 9 VWPC N Z B U V W V V V V V T S 8 VVP1 19 V U V U 10 WFO 11 WP 12 VWP1 13 VNC AC (2 PLACES) V U 14 VN1 15 NC 16 UN R P 17 VN Q 18 WN 19 FO AM AE (2 PLACES) AG AN AK AL AH AF AJ C W VUPC V OT UFO U IN VUP1 FO VCC UP GND GND IN FO VCC SI OUT IN FO VCC OT GND GND OT GND GND FO VCC IN N SI OUT IN GND GND OT VVPC VFO WP VWP1 VP VVP1 UN FO VCC SI OUT GND GND IN FO VCC SI OUT GND GND NC OT VN SI OUT WFO VWPC NC FO VNC VN1 WN SI OUT AD OT P Outline Drawing and Circuit Diagram Dimensions A B C D E F G H J K L M N P Q R S T U Inches 4.72 2.17 0.63 4.17 0.28 0.78 2.62 0.13 0.63 0.08 0.10 2.81 0.20 0.31 3.87 0.87 0.10 0.77 0.91 Millimeters 120.0 55.0 16.0 106.0 7.0 19.75 66.5 3.25 16.0 2.0 2.5 71.5 5.0 7.75 98.25 22.0 2.5 19.5 23.0 Dimensions V W X Y Z AA AB AC AD AE AF AG AH AJ AK AL AM AN Inches 0.16 1.01 2.00 0.69 0.30 0.98 0.10 Dia. 0.22 Dia. 0.67 0.10 Dia. 0.33 0.08 0.41 1.08 0.04 0.02 Sq. 0.06 0.04 Millimeters 4.0 25.75 50.75 17.5 7.5 25.0 Dia. 2.5 Dia. 5.5 17.0 Dia. 2.5 8.5 2.0 10.5 27.5 1.0 Sq. 0.5 1.5 1.0 Description: Powerex Intellimod™ Intelligent Power Modules are isolated base modules designed for power switching applications operating at frequencies to 20kHz. Built-in control circuits provide optimum gate drive and protection for the IGBT and free-wheel diode power devices. Features: £ Complete Output Power Circuit £ Gate Drive Circuit £ Protection Logic – Short Circuit – Over Temperature Using On-chip Temperature Sensing – Under Voltage £ Low Loss Using 5th Generation IGBT Chip Applications: £ Inverters £ UPS £ Motion/Servo Control £ Power Supplies Ordering Information: Example: Select the complete part number from the table below -i.e. PM25CLB120 is a 1200V, 25 Ampere Intellimod™ Intelligent Power Module. Type Current Rating Amperes VCES Volts (x 10) PM 25 120 1 Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM25CLB120 Intellimod™ L-Series Three Phase IGBT Inverter 25 Amperes/1200 Volts Absolute Maximum Ratings, Tj = 25°C unless otherwise specified Characteristics Symbol Power Device Junction Temperature PM25CLB120 Units Tj -20 to 150 °C Storage Temperature Tstg -40 to 125 °C Module Case Operating Temperature (See TC Measurement point Illustration) TC -20 to 100 °C Mounting Torque, M5 Mounting Screws — 31 in-lb Module Weight (Typical) — 340 Grams Supply Voltage, Surge (Applied between P - N) VCC(surge) 1000 Volts Self-protection Supply Voltage Limit (Short Circuit protection Capability)* VCC(prot.) 800 Volts VISO 2500 Volts VCES 1200 Volts ±IC 25 Amperes ±ICP 50 Amperes PC 148 Watts Supply Voltage (Applied between VUP1-VUPC, VVP1-VVPC, VWP1-VWPC, VN1-VNC) VD 20 Volts Input Voltage (Applied between UP-VUPC, VP-VVPC, WP-VWPC, UN- VN- WN-VNC) VCIN 20 Volts Fault Output Supply Voltage VFO 20 Volts IFO 20 mA Isolation Voltage, AC 1 minute, 60Hz Sinusoidal *VD = 13.5 ~ 16.5V, Inverter Part, Tj = 125°C IGBT Inverter Sector Collector-Emitter Voltage (VD = 15V, VCIN = 15V) Collector Current (TC = 25°C) Peak Collector Current (TC = 25°C) Collector Dissipation (TC = 25°C) Control Sector (Applied between UFO-VUPC, VFO-VVPC, WFO-VWPC, FO-VNC) Fault Output Current (UFO, VFO, WFO, FO Terminals) Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Collector-Emitter Cutoff Current ICES VCE = VCES, VD = 15V, Tj = 25°C — — 1.0 mA VCE = VCES, VD = 15V, Tj = 125°C — — 10 mA Diode Forward Voltage VEC -IC = 25A, VCIN = 15V, VD = 15V — 2.5 3.5 Volts VCE(sat) VD = 15V, VCIN = 0V, IC = 25A, — 1.9 — Volts — 1.9 — Volts IGBT Inverter Sector Collector-Emitter Saturation Voltage Tj = 25°C VD = 15V, VCIN = 0V, IC = 25A, Tj = 125°C Inductive Load Switching Times ton 0.5 1.0 2.5 µs trr VD = 15V, VCIN = 0 ⇔ 15V — 0.15 0.3 µs tC(on) VCC = 600V, IC = 25A — 0.4 1.0 µs toff Tj = 125°C — 2.0 3.0 µs — 0.7 1.2 µs tC(off) 2 Powerex, Inc., 200 E. Hillis Street, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 PM25CLB120 Intellimod™ L-Series Three Phase IGBT Inverter 25 Amperes/1200 Volts Electrical and Mechanical Characteristics, Tj = 25°C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units SC -20°C ≤ Tj ≤ 125°C, VD = 15V 50 — — Amperes toff(SC) VD = 15V — 10 — µs OT Trip Level 135 145 155 °C OTR Reset Level — 125 — °C UV Trip Level 11.5 12.0 12.5 Volts UVR Reset Level — 12.5 — Volts ID VD = 15V, VCIN = 15V, VN1-VNC — 15 25 mA Control Sector Short Circuit Trip Level Short Circuit Current Delay Time Over Temperature Protection (Detect Tj of IGBT Chip) Supply Circuit Under-voltage Protection (-20 ≤ Tj ≤ 125°C) Circuit Current VD = 15V, VCIN = 15V, VXP1-VXPC — 5 10 mA Input ON Threshold Voltage Vth(on) Applied between UP-VUPC, 1.2 1.5 1.8 Volts Input OFF Threshold Voltage Vth(off) VP-VVPC, WP-VWPC, UN- VN- WN-VNC 1.7 2.0 2.3 Volts Fault Output Current* IFO(H) VD = 15V, VCIN = 15V — — 0.01 mA IFO(L) VD = 15V, VCIN = 15V — 10 15 mA tFO VD = 15V 1.0 1.8 — ms Condition Min. Typ. Max. Units Rth(j-c)Q IGBT (Per 1/6 Module) — — 0.84** °C/Watt Rth(j-c)D FWDi (Per 1/6 Module) — — 1.36** °C/Watt Case to Fin Per Module, — — 0.038 °C/Watt Fault Output Pulse Width* *Fault output is given only when the internal SC, OT and UV protections schemes of either upper or lower devide operate to protect it. Thermal Characteristics Characteristic Symbol Junction to Case Thermal Resistance Contact Thermal Resistance Rth(c-f) Thermal Grease Applied ** If you use this value, Rth(f-a) should be measured just under the chips. Recommended Conditions for Use Characteristic Supply Voltage Control Supply Voltage*** Symbol Condition Value Units VCC Applied across P-N Terminals ≤800 Volts Applied between VUP1-VUPC, 15.0 ± 1.5 Volts VD VVP1-VVPC, VWP1-VWPC, VN1-VNC Input ON Voltage VCIN(on) Applied between UP-VUPC, ≤0.8 Volts Input OFF Voltage VCIN(off) VP-VVPC, WP-VWPC, UN- VN- WN-VNC ≥4.0 Volts ≤20 kHz Input Signal ≥2.5 µs PWM Input Frequency fPWM Arm Shoot-through Blocking Time tDEAD *** With ripple satisfying the following conditions: dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak. TC Measurement Point Y BOTTOM VIEW X Arm Axis UP VP WP UN VN WN IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi IGBT FWDi X 29.0 29.3 64.0 65.5 85.6 85.9 37.8 37.5 55.2 55.7 75.8 75.3 Y -7.1 1.5 -7.1 2.0 -7.1 2.0 5.1 -4.5 5.1 -4.5 5.1 -4.5 3