05076 PLCDA03 thru PLCDA24 Only One Name Means ProTek’Tion™ ULTRA LOW CAPACITANCE TVS ARRAY APPLICATIONS ✔ Ethernet - 10/100 Base T ✔ FireWire, SCSI & USB ✔ Audio/Video Inputs ✔ xDSL Interfaces ✔ Cellular Phone Terminals IEC COMPATIBILITY (EN61000-4) ✔ 61000-4-2 (ESD): Air - 15kV, Contact - 8kV ✔ 61000-4-4 (EFT): 40A - 5/50ns ✔ 61000-4-5 (Surge): 24A, 8/20µs - Level 2(Line-Gnd) & Level 3(Line-Line) SO-8 FEATURES ✔ 500 Watts Peak Pulse Power per Line (tp=8/20µs) ✔ Bidirectional Configuration ✔ Available in Multiple Voltage Types Ranging From 3V to 24V ✔ Protects Two (2) Lines ✔ ESD Protection > 40 kilovolts ✔ ULTRA LOW CAPACITANCE: 5pF ✔ RoHS Compliant in Lead-Free Versions MECHANICAL CHARACTERISTICS ✔ ✔ ✔ ✔ Molded JEDEC SO-8 Package Weight 70 milligrams (Approximate) Available in Tin-Lead or Lead-Free Pure-Tin Plating(Annealed) Solder Reflow Temperature: Tin-Lead - Sn/Pb, 85/15: 240-245°C Pure-Tin - Sn, 100: 260-270°C ✔ Flammability Rating UL 94V-0 ✔ 12mm Tape and Reel Per EIA Standard 481 ✔ Marking: Logo, Marking Code, Date Code & Pin One Defined By Dot on Top of Package PIN CONFIGURATION 05076.R 7 4/05 8 7 6 5 1 2 3 4 1 www.protekdevices.com PLCDA03 thru PLCDA24 DEVICE CHARACTERISTICS MAXIMUM RATINGS @ 25°C Unless Otherwise Specified SYMBOL VALUE UNITS Peak Pulse Power (tp = 8/20µs) - See Figure 1 PPP 500 Watts Operating Temperature TJ -55°C to 150°C °C TSTG -55°C to 150°C °C PARAMETER Storage Temperature ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified PART NUMBER (See Note 1) PLCDA03 PLCDA05 PLCDA08 PLCDA12 PLCDA15 PLCDA24 DEVICE MARKING SGA SGB SGF SGC SGD SGE RATED STAND-OFF VOLTAGE MINIMUM BREAKDOWN VOLTAGE MAXIMUM CLAMPING VOLTAGE (See Fig. 2) MAXIMUM CLAMPING VOLTAGE (See Fig. 2) VWM VOLTS @ 1mA V(BR) VOLTS @ IP = 1A VC VOLTS 3.3 5.0 8.0 12.0 15.0 24.0 4.5 6.0 8.5 13.3 16.7 26.7 7.0 9.8 13.4 19.0 24.0 43.0 MAXIMUM LEAKAGE CURRENT MAXIMUM CAPACITANCE (See Note 2) @8/20µs VC @ IPP @VWM ID µA @0V, 1 MHz C pF 10.9V @ 43.0A 13.5V @ 42.0A 16.0V @ 34.0A 25.9V @ 21.0A 30.0V @ 17.0A 49.0V @ 12.0A 125 20 10 1 1 1 5 5 5 5 5 5 Note 1: Devices are designed to be used in parallel (See Circuit Diagram). For other applications, contact the factory. Do not apply surge in the “forward” direction of the TVS. Note 1: Do not surge from pins 8 to 1, 2 to 7, 6 to 3 and 4 to 5. PIV typically greater than 100V for each rectifier die. Electrical characteristics apply to pins 1 to 8, 7 to 2, 3 to 6 and 5 to 4. 500W 8/20µs Waveform 1,000 100 10 0.1 05076.R 7 4/05 FIGURE 2 PULSE WAVE FORM 120 IPP - Peak Pulse Current - % of IPP PPP - Peak Pulse Power - Watts 10,000 FIGURE 1 PEAK PULSE POWER VS PULSE TIME tf 100 TEST WAVEFORM PARAMETERS tf = 8µs td = 20µs Peak Value IPP 80 e-t 60 40 td = t I /2 PP 20 0 1 10 100 td - Pulse Duration - µs 1,000 10,000 2 0 5 10 15 t - Time - µs 20 25 30 www.protekdevices.com PLCDA03 thru PLCDA24 GRAPHS FIGURE 3 POWER DERATING CURVE FIGURE 4 OVERSHOOT & CLAMPING VOLTAGE FOR PLCDA05 100 40 Peak Pulse Power 8/20µs 5 Volts per Division % Of Rated Power 80 60 40 30 20 10 20 0 Average Power 0 0 25 50 75 100 125 TL - Lead Temperature - °C 150 ESD Test Pulse: 25 kilovolt, 1/30ns (waveshape) VC - Clamping Voltage - Volts FIGURE 5 TYPICAL CLAMPING VOLTAGE VS PEAK PULSE CURRENT FOR PLCDA15 30 20 10 0 0 2 4 6 8 IPP - Peak Pulse Current - Amps FIGURE 6 INSERTION LOSS - PLCDA05 20 db 10 db per Division 10 db per Division 12 FIGURE 7 RETURN LOSS - PLCDA05 20 db Ref 0 db -20 db Ref 0 db -20 db -50 db -50 db 100 MHz per Division 100 MHz per Division 05076.R 7 4/05 10 3 www.protekdevices.com PLCDA03 thru PLCDA24 APPLICATION NOTE The PLCDA Series are low capacitance, bidirectional TVS arrays that are designed to protect I/O or high speed data lines from the damaging effects of ESD or EFT. This product series has a surge capability of 500 Watts PPP per line for an 8/20µs waveshape and offers ESD protection > 40kv. BIDIRECTIONAL COMMON-MODE CONFIGURATION (Figure 1) Ideal for use in USB applications, the PLCDA Series provides up to two (2) lines of protection in a common-mode configuration as depicted in Figure 1. Circuit connectivity is as follows: ✔ Pins 1 & 2 and 3 & 4 are connected to Ground ✔ Pins 5 and 6 are connected to I/O Line D+ ✔ Pins 7 and 8 are connected to I/O Line D- Figure 1. Typical Common-Mode USB Protection Circuit D+ USB IC CIRCUIT BOARD LAYOUT RECOMMENDATIONS D- Circuit board layout is critical for Electromagnetic Compatibility (EMC) protection. The following guidelines are recommended: ✔ The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. ✔ The path length between the TVS device and the protected line should be minimized. ✔ All conductive loops including power and ground loops should be minimized. ✔ The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. ✔ Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. 05076.R 7 4/05 8 7 6 5 1 2 3 4 GND 4 www.protekdevices.com PLCDA03 thru PLCDA24 PACKAGE OUTLINE & DIMENSIONS PACKAGE OUTLINE SO-8 -A- 8 5 + 0.010 (0.25 MM) M B M 4 PL -B - P 1 G PACKAGE DIMENSIONS 4 DIM A B C D F G J K P R D C R x 45° 0° - 10° -T- K 0.010 (0.25 MM) M T B S A S 8 PL + J F MILLIMETERS MIN MAX 4.80 3.80 1.35 0.35 0.40 1.27 BSC 0.18 0.10 5.80 0.25 INCHES MIN MAX 5.00 0.189 0.196 4.00 0.150 0.157 0.054 0.068 1.75 0.49 0.014 0.019 0.049 1.250 0.016 1.27 BSC 0.05 BSC 0.05 BSC 0.25 0.007 0.009 0.004 0.008 0.25 6.20 0.229 0.244 0.019 0.50 0.010 NOTES 1. 2. 3. 4. 5. 6. MOUNTING PAD 0.050 ± 0.005 0.030 ± 0.005 - T - = Seating Plane and Datum Surface. Dimensions “A” and “B” are Datum. Dimensions “A” and “B” do not include mold protrusion. Maximum mold protrusion is 0.015” (0.380 mm) per side. Dimensioning and tolerances per ANSI Y14.5M, 1982. Dimensions are exclusive of mold flash and metal burrs. TAPE & REEL/BULK ORDERING NOMENCLATURE 0.160 ± 0.005 1. Surface mount product is taped and reeled in accordance with EIA-481. 2. Suffix-T7 = 7 Inch Reel - 1,000 pieces per 12mm tape, i.e., PLCDA05-T7. 3. Suffix-T13 = 13 Inch Reel - 2,500 pieces per 12mm tape, i.e., PLCDA05-T13. 4. Suffix - LF = Lead-Free, Pure-Tin Plating, i.e., PLCDA05-LF-T7. 5. No Suffix = Product Shipped in Tubes of 98 pcs per Tube. 0.245 MIN 0.045 ± 0.005 Outline & Dimensions: Rev 1 - 11/01, 06009 COPYRIGHT © ProTek Devices 2005 SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC). DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products. 05076.R 7 4/05 5 ProTek Devices 2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: [email protected] Web Site: www.protekdevices.com www.protekdevices.com