MMIC AP2301 (Old part#: AP230S12) `Product Features Application • Small size • SMD Type Package • NO matching circuit needed • High efficiency • Dual supply voltage • Higher linearity • 12 pin Air cavity package • Higher productivity • Lower manufacturing cost • GaAs MMIC • 3 – 2000MHz • -63dBc CSO 135 Channels@ output Level +37dBmV • -60dBc CTB 135 Channels@ output Level +37dBmV • Satellite • Converter • CATV • Optical node Package : SP12 Description The power amplifier is designed for base stations and repeater systems. GaAs MMIC is used and attached on a copper carrier of 12 pin air cavity package with dual supply voltage. *The data in this spec sheet is valid only for 75 ohm application. 50 ohm data is in a separate spec sheet. Operating Ranges PARAMETER UNIT Device Voltage VDC Case Temperature ℃ MIN TYP MAX +5 +5.3 - +85 -40 Absolute Minimum and Maximum Ratings PARAMETER UNIT Device Voltage VDC MIN MAX +5.5 Device Current mA +320 RF Input Power dBm Storage Temperature ℃ +10 -40 +150 Specifications T=25℃, Vcc=5.0V, 75Ω system Parameter Units Frequency Range Supply Voltage Single Ended CATV Evaluation Circuit Current S21-Gain S21-Gain S21-Gain M Hz V S11-Input Return Loss S22-Output Return Loss Noise Figure OIP3 OIP1 dB dB dBm dBm S11-Input Return Loss S22-Output Return Loss OIP3 OIP1 Noise Figure CSO 50 - 870M Hz CTB XM D CSO 3 - 150M Hz CTB XM D dB dB dBm dBm dB dBc dBc dBc dBc dBc dBc mA dB dB dB M inimum Typical M aximum 3M Hz~2.0GHz 5 200 220 16 14.5 15 14.5 15 Reverse ( 3 ~ 200M Hz ) -16 -16 5.5 41 43 20 22 Forward ( 50 ~ 870M Hz ) -11 -11 36 38 20 22 4 -63 -60 -60 -70 -73 -70 Condition Vcc=5V 250 3M Hz 50M Hz 2000M Hz -13 -13 +10dBm/2 tone separated by 1M Hz At 100M Hz -8 -8 +10dBm/2 tone separated by 1M Hz At 800M Hz 6 -55 -60 -55 135 channels,+37dBmV/ch,Single 135 channels,+37dBmV/ch,Single 135 channels,+37dBmV/ch,Single 8 channels,+45dBmV/ch,Single 8 channels,+45dBmV/ch,Single 8 channels,+45dBmV/ch,Single ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 2.0 MMIC AP2301 (Old part#: AP230S12) Application Circuit: 3MHz ~ 200MHz S-Parameters 30 7 S21 Noise Figure(dB) Magnitude(dB) 20 10 0 -10 Noise Figure 8 S22 6 5 4 -20 S11 -30 3 5 0 30 60 90 120 150 180 210 240 270 300 5 Frequency(MHz) 100 150 200 250 Frequency(MHz) P1dB 25 50 OIP3 50 45 OIP3(dBm) dBm 20 15 10 5 40 35 30 25 20 15 0 5 50 100 150 200 5 250 50 100 Frequency(MHz) Level: +45dBmV FRQ 150 200 250 Frequency(MHz) Tilt: 8CH FLAT XMD(NCTA) CTB_RAW CTB_COR N-FLR CSU_RAW CSU_COR CSU_FRQ 7.63 CSL_RAW 71.7 CSL_COR CSL_FRQ 7 72.2 79.9 80.1 93.6 92.4 96.7 71.7 31 72.8 78.6 78.8 92.1 78.1 78.4 32 76.6 76.8 29.99 49 72.1 79.8 80.1 91.8 78.2 78.4 49.99 90.5 94.8 48.31 ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 2.0 5.99 MMIC AP2301 (Old part#: AP230S12) Application Circuit: 30MHz ~ 2000MHz Performance Charts (Vdc=5V, Id=220mA, Tc=25℃) Noise Figure Vs. Frequency 17 6 10 15 5 0 13 -10 11 -20 9 -30 7 1 -40 5 2000 0 0 200 400 600 800 1000 1200 1400 1600 1800 Noise Figure(dB) 20 Gain(dB) Return Loss(dB) S-parameter Vs. Frequency 4 3 2 30 200 400 600 S11 S22 1000 1200 1400 1600 1800 2000 1400 1600 1800 2000 NF(dB) Gain(dB) P1dB V s. Frequency OIP3 V s. Frequency 45 30 41 25 P1dB(dBm) OIP3(dBm) 800 Freq(MHz ) Freq(MHz ) 37 33 29 20 15 10 5 25 0 21 30 200 400 600 800 1000 1200 1400 1600 1800 2000 30 200 400 600 800 1000 1200 Freq(MHz ) Freq(MHz ) P1dB OIP3(dBm) ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 2.0 MMIC AP2301 (Old part#: AP230S12) Multi-Tone Test 135ch@+30dBmV (Vcc +5V) Level: +30dBm FRQ Tilt: FLAT_CH135 XMD(NCTA) CTB_RAW CTB_COR N-FLR CSU_RAW CSU_COR CSU_FRQ CSL_RAW CSL_COR CSL_FRQ 55.25 74.2 75.5 79.8 76.9 76.6 80.9 55.93 76 80.3 54 77.25 75 76.1 80.4 77.1 76.1 80.4 77.99 76.9 81.2 76.25 109.25 74.9 76.1 80.4 77.6 77.5 81.8 109.96 77.1 81.4 107.99 211.25 74.8 76.1 80.4 77.7 77.4 81.8 212.31 77.1 81.4 209.99 331.25 75.7 74.9 79.2 76.3 76 80.4 331.88 75.9 80.2 329.98 445.25 76.3 75.6 79.9 77 76.7 81.1 446.48 76.6 81 443.98 547.25 77.7 74.3 78.7 75.3 74.9 79.2 548.42 74.9 79.2 545.99 637.25 77.4 74.5 78.8 75.8 75 79.3 638.49 75.4 79.7 635.99 745.25 77.4 73.9 78.3 75.2 74.2 78.6 746.48 74.8 79.2 743.92 859.25 77.8 72.6 76.9 73.6 72.6 77 860.48 73.2 77.5 858.49 Min 74.2 72.6 76.9 73.6 72.6 77 55.93 73.2 77.5 54 Max 77.8 76.1 80.4 77.7 77.5 81.8 860.48 77.1 81.4 858.49 Multi-Tone Test 135ch@+37dBmV (Vcc +5V) Level: +37dBmV FRQ Tilt: 135CH FLAT XMD(NCTA) CTB_RAW CTB_COR N-FLR CSU_RAW CSU_COR CSU_FRQ CSL_RAW CSL_COR CSL_FRQ 55.25 60.4 66.7 66.9 82.9 80.2 83.2 55.99 67.4 67.5 53.99 77.25 60.9 68.3 68.4 83.2 68.5 68.7 78 82.9 87.2 76.22 109.25 61 66.4 66.4 84.1 80.3 82.9 110 70.4 70.6 108 211.25 60.4 66.9 67 83.6 76.1 77 212.5 71.5 71.8 209.99 331.25 61.6 65.7 65.7 82.5 73.3 73.9 332.5 72.3 72.8 329.99 445.25 61.5 66.2 66.3 82.9 73.2 73.7 446.49 73.8 74.4 443.99 547.25 62.7 66.3 66.4 81.4 72.4 73 548.5 74.1 75.1 545.99 637.25 62.5 66.1 66.3 81.6 73.2 73.9 638.49 75.9 77.2 635.98 745.25 62.8 66.6 66.8 81.5 73.9 74.7 746.5 78.1 80.6 743.99 859.25 63.3 67 67.2 79.7 74.4 76.1 860.49 78.8 83.1 858.49 Min 60.4 65.7 65.7 79.7 68.5 68.7 55.99 67.4 67.5 53.99 Max 63.3 68.3 68.4 84.1 80.3 83.2 860.49 82.9 87.2 858.49 ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 2.0 MMIC AP2301 (Old part#: AP230S12) ESD PROTECTION For a safe use in all situations, it is recommended to have proper ESD control techniques while the device is being handled. Here are some recommended precautions; - Person at a workbench should be earthed via a wrist strap and a resistor. - All mains-powered equipment should be connected to the mains via an earth-leakage switch. - Equipment cases should be grounded. - Relative humidity should be maintained between 40% and 50%. - An ionizer is recommended. - Keep static materials, such as plastic envelopes and plastic trays etc. away from the workbench Dimension : PMBG-SQFP-12 Outline Drawing Block Diagram 4 3 AMP2 3 7 (SQ.) 7 4 E C AMP1 10 1 1 12 10 12 D F Function Pin No. Input 7, 9 Output , Bias 1, 3 Ground B (SQ.) A (SQ.) Land Pattern 4 1.02 2,4, 5, 6,8, 10, 11, 12 3 Backside Copper F G 1 H J K (SQ.) INCH No. MM 0.282 A 7.16 0.2 B 5.08 0.246 C 6.25 0.069 1.75 0.015 D E 0.03 F 0.76 0.2 G 0.51 0.4 H 1.02 0.14 J 0.36 0.83 K M 2.1 0.32 M RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC. ▪ Tel : 82-31-250-5011 ▪ All specifications may change without notice. ▪ [email protected] ▪ Version 2.0 0.38 0.8