OC-48 LR-1/STM16 L-16.1 SFP Transceiver SP-48-LR1 Features • Compliant with OC48/STM-16 Standards • Single 3.3 V supply • 40 km reach • 25 dB min, 29.5 dB typical link budget • Commercial Temperature Available (-CxA) • Industrial Temperature Available (-TxA) • Reduced Temperature Available (-RxA) • 1310nm DFB Laser • APD receiver • SFP MSA SFF-8074i compliant • GR 253/STM G.957 compliant • Telcordia GR-468 compliant • Digital Diagnostic SFF-8472 Rev. 9.3 compliant • Color code Bail Latch : Red • RoHS compliant General Operating Parameter Supply Voltage Symbol Min. Typ. Max. Unit Vcc 3.135 3.3 3.465 V Total Current ICC - - 300 mA Power Supply Noise Rejectiona PSR 100 - - mVp-p Operating Temperature(-CDA) Top -5 - 70 ºC Operating Temperature(-RDA) Top -20 - 85 ºC Operating Temperature(-TDA) Top -40 - 85 ºC Storage Temperature Tstg -40 - 85 ºC Data Rate OC48/STM-16 DR - 2488.32 - Mbps a) 20Hz to 155MHz Transmitter Specifications, Optical Parameter Symbol Min Typical Max Unit Optical Power Pop -2 0.5 3 dBm Average Launch Power of Off Tx Poff - - -30 dBm Extinction Ratio ER 8.2 - - dB Eye Mask SONET/SDH compliant Jgen - - 0.007 UI Optical Rise Timeb Optical Jitter Generation tr - - 160 ps Optical Fall Timeb tf - - 160 ps λ 1280 1310 1335 nm ∆λ - - 1 nm Mean Wavelength Spectral Width (20dB) Dispersion Penalty (40Km)c - 1 dB Relative Intensity Noise RIN dp - - -120 dB/Hz Reflectance Toleranced rp -24 - - dB b) 20%-80% values c) Measured at BER of 1e-10, PRBS of 223-1, at eye center d) 1dB degradation of receiver sensitivity LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS1524-Jul0507 Rev A.1 OC-48 LR-1/STM16 L-16.1 SFP Transceiver SP-48-LR1 Transmitter Specifications , Electrical Parameter Symbol Min Typical Max Unit Rin 80 100 120 Ω Vin, p-p 250 - 1200 mV Vfault 2 - Vcc V Vnormal Vd Vee - Vee + 0.5 V TxDisable_Disable 2 - Vcc V TxDisable_Enable Ven Vee - Vee + 0.8 V Parameter Symbol Min Typical Max Unit Receiver Power Lowe Rsens,low - -29 -27 dBm Input Differential Impedence PECL Single Ended data input swing TxFault_Fault TxFault_Normal Receiver Specifications, Optical Receiver Power Highe Rsens,high -6 - - dBm Pin, damage 4 - - dBm λ 1280 1310 1335 nm RX_r - - -27 dB LOS Assert - -42 - - dBm LOS De-assert - - - -27 dBm LOS Hysteresis - 0.5 - - dB Parameter Symbol Min Typical Max Unit PECL Single Ended Data Output Swing Vout,p-p 185 - 800 mV Data Output Rise Time tr - - 175 ps Data Output Fall Time tf - - 175 ps Max Unit Damage Threshold for Receiver Wavelengthf Maximum Reflectance of Receiver e) At 10-10 BER, PRBS 223-1 f) Operational over 1200-1625 nm range Electrical Output Timing and Electrical Parameter Symbol Min Typical Tx Disable Negate time t_on - - 1 ms Tx Disable assert time t_off - - 10 µs t_init - - 300 ms Tx fault Assert time Time to initialize, including reset of Tx fault t_fault - - 100 µs Tx Disable to reset t_reset 10 - - µs t_loss_on - - 100 µs t_loss_off f_serial_clock Rx_LOSH 2 - 100 100 - µs KHz V LOS Assert time LOS De-assert time Serial ID Clock Rate RX_LOS Voltage (high) RX_LOS Voltage (low) RX_LOSL - - 0.8 V LOS output voltage-Fault VLOS fault 2 - Vcc V VLOS normal Vee - Vee + 0.5 V MOD_DEF (0:2)-High Vh 2 - VI Vee - Vcc Vee + 0.5 V MOD_DEF (0:2)-Low LOS output voltage-Normal LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 V LUMNDS1524-Jul0507 Rev A.1 OC-48 LR-1/STM16 L-16.1 SFP Transceiver SP-48-LR1 Diagnostics Parameter Range Accuracy Unit Calibration Temperature (-CDA) -5 to 70 ±3 ºC External Tc(C) = Tslope*Tad(16 bit signed twos complement value) + Toffset Formula Temperature (-RDA) -20 to 85 ±3 ºC External Tc(C) = Tslope*Tad(16 bit signed twos complement value) + Toffset Temperature (-TDA) -40 to 85 ±3 ºC External Tc(C) = Tslope*Tad(16 bit signed twos complement value) + Toffset Voltage 0 to Vcc 0.1 V External V(Volts) = Vslope*Vad (16 bit unsigned integer) + Voffset Bias Current 0 to 120 5 mA External I(mA) = Islope * Iad(16 bit unsigned integer)+Ioffset Tx Power -2 to 3 ±3dB dBm External Tx_PWR(µW) = Tx_PWRslope*Tx_PWRad(16 bit unsigned integer)+Tx_ PWRoffset Rx Power -31 to -6 ±3dB dBm External Rx_PWR(µW) = A0+A1*x+A2*x^2+A3*x^3+A4*x^4 EEPROM Serial ID Name of Field Vendor Name Vendor OUI Vendor PN LUMINENTOIC.COM Discription of Field SFPVendor name (ASCII) IEEE vendor OUI code for LuminentOIC Inc. Part number in ASCII, e.g. SP-48-LR1-CDA Address Hex 20 4C L 21 55 U 22 4D M 23 49 I 24 4E N 25 45 E 26 4E N 27 54 T 28 4F O 29 49 I 30 43 C 37 00 38 06 39 B5 40 53 41 50 P 42 34 4 43 38 8 44 4C L 45 52 R 46 31 47 43 1 C 48 44 D 49 41 A 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 ASCII S LUMNDS1524-Jul0507 Rev A.1 OC-48 LR-1/STM16 L-16.1 SFP Transceiver SP-48-LR1 Pinout Definitions Pin Function Notes 1 VeeT TX GND 2 TX_FAULT Open Collector 3 TX_DISABLE Internally Pulled High 4 MOD_DEF2 Serial Data Input 5 MOD_DEF1 Serial Clock Input 6 MOD_DEF0 Internally Grounded 7 NC Not Connected 8 LOS Open Collector 9 VeeR RX Ground 10 VeeR RX Ground 11 VeeR RX Ground 12 RXD- RX Data Negative 13 RXD+ RX Data Positive 14 VeeR RX GND 15 VCCR RX Power 16 VCCT TX Power 17 VeeT TX GND 18 TXD+ TX Data Positive 19 TXD- TX Data Negative 20 VeeT TX GND LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS1524-Jul0507 Rev A.1 OC-48 LR-1/STM16 L-16.1 SFP Transceiver SP-48-LR1 Outline Drawing Units in mm(inches) LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS1524-Jul0507 Rev A.1 OC-48 LR-1/STM16 L-16.1 SFP Transceiver SP-48-LR1 Suggested Transceiver Interface 1�H Vcc 10�F 1�H 0.1�F VCCT .01�F Protocol IC LuminentOIC SFP 10K� R1 TX_DISABLE TX_DISABLE TX_FAULT TX_FAULT TD + SerDes Laser Driver .01�F 100� TD VEET .01�F VCCR 10�F 0.1�F RD + Receiver Amplifier .01�F 100� RD - RX_LOS RX_LOS Vcc R VEER 1 R1 R1 .01�F EEPROM R1 MOD_DEF 2 MOD_DEF 1 MOD_DEF 0 R1=4.7K to 10K� LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS1524-Jul0507 Rev A.1 OC-48 LR-1/STM-16 L-16.1 SFP Transceiver SP-48-LR1 Ordering Information Available Options: SP-48-LR1-CDA SP-48-LR1-TDA SP-48-LR1-RDA SP-48-LR1-CNA SP-48-LR1-TNA SP-48-LR1-RNA Part Numbering Definition: S P - 0 3 - L R 1 - Temperature Diagnostic Revision • SP = Small Form Pluggable • 48 = OC48 • LR1 = Long Reach 40 km • Operatating Temperature C= Commercial temperature (-5 to 70ºC) T= Industrial temperature (-40 to 85ºC) R = Reduced Industrial (-20 to 85ºC) • Diagnostic D = Digital Diagnostic (SFF-8472) N = No Diagnostic • Design Revision A = RoHS compliant Warnings: Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. Legal Notes: IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2003 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS1524-Jul0507 Rev A.1