SOURCE SPS-43-48H-HP-TDE

1490nm/1310nm Single Fiber OLT Transceiver
Preliminary Datasheet
SPS-43-48H-HP-xDE (x=C, R, T)
Features
• Burst receive GPON OLT transceiver
• Small Form Factor Pluggable, Simple SC Connector
• “Fast Signal Detect” feature reduces ranging overhead
• Simplifed OLT “reset” timing
• 1490 nm DFB Tx with isolator
• 1310 nm APD Rx
• 2488 Mbps downstream Tx/1244 Mbps upstream Rx
• Single 3.3 V supply
• ITU-T G.984.2 compliant
• 20 km reach; 28 dB link budget
• RoHS-5/6 compliant (lead exemption)
General Operating
Parameter
Operating Voltage
Symbol
Min.
Typ.
Max.
Unit
Vcc
3.135
3.3
3.465
V
Total Supply Current
ICC
-
-
500
mA
Case Operating Temerature (-CDE)
Topr
-5
-
70
ºC
Case Operating Temerature (-RDE)
Topr
-20
-
85
ºC
Case Operating Temerature (-TDE)
Topr
-40
-
85
ºC
Storage Temperature
Tstg
-40
-
85
ºC
Symbol
General Optical Parameters
Parameter
Min.
Typ.
Max.
Unit
Back Reflection at 1490 nm
-
-
-20
dB
Back Reflection at 1310 nm
-
-
-20
dB
1490 nm to 1310 nm crosstalk
-
-
-45
dB
Symbol
Min
Typical
Max
Unit
Optical Power
Pop
1.5
-
5
dBm
Average launch power of off Tx
Poff
-
-
-40
dBm
λ
1480
1490
1500
nm
Transmitter Specifications (Optical)
Parameter
Wavelength
∆λ20
-
-
1
nm
SMSR
30
-
-
dB
ER
10
-
-
dB
Bit Rate
-
2488
-
Mbps
Optical Rise timea
-
-
160
ps
-
-
160
-15
-
Spectral Width (-20 dB)
Side Mode Suppression Ratio
Extinction Ratio
G.984.2
Transmit eye mask
Optical Fall
timea
Tolerence to TX back reflectionb
ps
dB
a) 20% to 80% values
b) 1 dB degradation of receiver sensitivity
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
1
LUMNDS2036-FEB1108
rev. 0.2 SHORT FORM
1490nm/1310nm Single Fiber OLT Transceiver
Preliminary Datasheet
SPS-43-48H-HP-xDE (x=C, R, T)
Transmitter Specifications (Electrical)
Parameter
Symbol
Input Differential Impedence
Single Ended data input swing (ac coupled inside module)
Tx Disable (LVTTL)
Tx Enable (LVTTL)
Tx_Fail_High
Tx_Fail_Normal
Min
Typical
Max
Unit
Rin
80
100
120
Ω
Vin, p-p
300
-
1200
mV
Vd
2
-
Vcc
V
Ven
0
-
0.8
V
V_Fail
2.4
-
Vcc
V
V_Normal
0
-
0.4
V
Receiver Specifications (Optical)
Parameter
Symbol
Min
Typical
Max
Unit
Wavelength
λ
1260
1310
1360
nm
Data Rate (burst-mode)
-
1244
-
Mbps
Receiver Sensitivityc
RENS
-
-
-28
dBm
Receiver Overloadc
ROL
-8
-
-
dBm
15
20
-
dB
dBm
Receiver Burst-mode Dynamic Ranged
BRST_Det Assert (Signal Detected)
Receiver CID Tolerance
Damage Threshold for Receiver
Maximum Reflectance of Receiver
P_DET
CID
-
-
-28
72
-
-
bits
Pin, damage
3
-
-
dBm
RX_r
-
-
-20
dB
c) At 10-10 BER with PRBS 223-1 data
d) The input power difference between two subsequent high and low burst data.
Receiver Specifications (Electrical)
Parameter
Symbol
Min
PECL Single ended data output swing(LVPECL)
Typical
Max
Unit
Vout,p-p
250
-
800
mV
Data output rise timee
tr
-
250
-
ps
Data output fall timee
tf
-
250
-
ps
V_DETH
2.4
-
Vcc
V
V_DETL
0
-
0.4
V
T_BRST_Det
-
-
6.4
nS
BRST_Det_Highf
f
BRST_Det_Low
BRST_Det Response Time
e) 20% to 80% values
f) BRST_Det assert low when module receive “reset” signal, assert high when incoming burst is detected and latch to high state until next
“Reset” signal.
Digital RSSI Timing Specification
Parameter
RSSI Trigger Delayg
g
RSSI Sampling Time
g
Internal I2C Delay
Reciever Power DDM (RSSI) Errorh
Symbol
Min
Typical
Max
Unit
TTrigger
25
-
-
nS
RSSISample
300
-
-
nS
TI2C
RXDDM
-
-
500
+/- 3
µS
dB
g) RSSI_ACQ Input signal rising edge will trigger RSSI sampling, and falling edge will trigger internal digital RSSI information written to I2C.
It is recommended that host shall not trigger RSSI_ACQ input again until RSSI data is valid in I2C from previous RSSI trigger.
h) RSSI DDM working range is between -8 to -30 dBm. RSSI DDM accuracy is better than +/- 3dB for input power levels between -10 to -30 dBm,
the accuracy reduces to +/- 5dBm for power levels larger than -10dBm.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
2
LUMNDS2036-FEB1108
rev. 0.2 SHORT FORM
1490nm/1310nm Single Fiber OLT Transceiver
Preliminary Datasheet
SPS-43-48H-HP-xDE (x=C, R, T)
Pinout Definitions
Pin
Function
Notes
1
Veet
Tx Ground
2
Tx_Fail
(Tx_Fault)
Tx Fail Alarm. LVTTL Output Active High
3
TX_DIS
Tx Disable. LVTTL input. Laser output is disabled when this pin is asserted high or left
unconnected. Laser output is enabled when this pin is asserted low.
4
MOD_DEF (2)
2-Wire Serial Data I/O Pin.
5
6
MOD_DEF (1)
MOD_DEF (0)
2-Wire Serial Clock Input.
Internally Grounded
7
Reset
CMOS input. Assert “Reset” high at the end of previous burst, 2 bytes in duration
8
BRST_Det
LVTTL output. BRST_Det assert low when module receives “reset” signal, assert high
when incoming burst is present.
9
RSSI_ACQ
RSSI acquire/hold LVTTL Input. Digital RSSI output through I2C
10
Veer
Rx Ground
11
Veer
Rx Ground
12
RXD-
Negative Data Output, LVPECL; DC coupled
13
RXD+
Positive Data Output, LVPECL; DC coupled
14
15
16
Veer
Vcc_RX
Vcc_TX
Rx Ground
Rx Vcc
Tx Vcc
17
Veet
Tx Ground
18
TXD+
Positive Data Input, LVPECL or CML (AC coupled; internally 100 ohms differential
termination)
19
TXD-
Negative Data Input, LVPECLor CML (AC coupled; internally 100 ohms differential
termination)
20
Veet
LUMINENTOIC.COM
Tx Ground
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
3
LUMNDS2036-FEB1108
rev. 0.2 SHORT FORM
1490nm/1310nm Single Fiber OLT Transceiver
Preliminary Datasheet
SPS-43-48H-HP-xDE (x=C, R, T)
Timing Diagram
Detailed burst-mode receiver timing diagram is available upon request.
Digital RSSI Acquire/Hold Timing Specification
Detailed digital RSSI Acquisition/Hold timing diagram is available upon request.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
4
LUMNDS2036-FEB1108
rev. 0.2 SHORT FORM
1490nm/1310nm Single Fiber OLT Transceiver
Preliminary Datasheet
SPS-43-48H-HP-xDE (x=C, R, T)
DEC
Addr.
HEX
Addr.
Field Size
(bytes)
I2C A0h Address
0
00
1
1
01
1
2
02
1
Name
Default Value
Description
Identifier
Extended Identifier
Connector
03h
04h
01h
SFP tranceiver
Function defined by serial ID
SC receptacle
3
03
8
Transceiver
00 00 00 00 00 00 00 00h
Ext Calibration, Average Power Measurement
11
12
13
14
15
16
17
18
19
20
36
37
40
56
60
62
0B
0C
0D
0E
0F
10
11
12
13
14
24
25
28
38
3C
3E
1
1
1
1
1
1
1
1
1
16
1
3
16
4
2
1
Encoding
Nominal Bit Rate in 100 MBps
Reserved
Length (9µ, km) in km
Length (9µ, m) in 100 m
Length (50µ) in 10 m
Length (62.5µ) in 10 m
Length (Copper) in m
Reserved
Vendor Name (ASCII)
Reserved
Vender IEEE Company ID
Vendor Part Number (ASCII)
Vendor Rev (ASCII)
Laser Wavelength in nm
Reserved
03h
19h
00h
14h
C8h
00h
00h
00h
00h
"LUMINENTOIC "
00h
00 06 B5h
"SPS4348HHPxDE "
31 20 20 20h
05 D2h
00h
NRZ encoding
2488.32 Mbps
Reserved
20km
20km
Not Supported
Not Supported
Not Supported
Reserved
Vendor Name (ASCII)
Reserved
LuminentOIC IEEE ID
Vendor Part Number (ASCII); x=C, R, T
Revision
1490nm Tx Wavelength
Reserved
63
3F
1
Check Code for Base ID Fields
xxh
Checksum from byte 0-62
64
66
67
68
40
42
43
44
2
1
1
16
Options
Upper Bit Rate Margin in %
Lower Bit Rate Margin in %
Vendor Serial Number (ASCII)
00 1Ch
00h
00h
"xxxxxxxxxxxxxxxx"
TX_DIS, TX_Fault, SD
BR, Max not specified
BR, Min not specified
16 byte Serial number field (ASCII)
84
54
8
Date Code
xx xx xx xx xx xx 20 20h
Year(2 bytes) month(2 bytes) day(2 bytes)
92
5C
1
Diagnostic Monitoring Type
58h
Ext Calibration, Average Power Measurement
93
5D
1
Enhanced Options
E0h
94
5E
1
02h
95
5F
1
xxh
Checksum from byte 64-69
96
126
128
60
7E
80
30
2
128
SFF-8472 Compliance
Check Code for Extended ID
Fields
Vendor Specific
Vendor Specific
Reserved
Optical Alarm/warning implemented
Soft TX_DIS, TX_FAULT implemented
Compliance to SFF-8472 Rev 9.4
"SPS-43-48H-HP-xDE
00 00h
00….00h
"
LOIC part number (ASCII); x=C, R, T
Reserved
Reserved; return to 0
For detailed specifications of EEPROM contents and externally calibrated digital diagnostic monitor (DDM) functions, please refer to SFF-8472
standard Rev 9.5.
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
5
LUMNDS2036-FEB1108
rev. 0.2 SHORT FORM
1490nm/1310nm Single Fiber OLT Transceiver
Preliminary Datasheet
SPS-43-48H-HP-xDE (x=C, R, T)
DEC
Addr.
HEX
Addr.
Field Size
(bytes)
I2C A2h Address
0
00
2
2
02
2
4
04
2
6
06
2
8
08
2
10
0A
2
12
0C
2
14
0E
2
16
10
2
18
12
2
20
14
2
22
16
2
24
18
2
26
1A
2
28
1C
2
30
1E
2
32
20
2
34
22
2
36
24
2
38
26
2
40
28
16
56
38
4
60
3C
4
64
40
4
68
44
4
72
48
4
76
4C
2
78
4E
2
80
50
2
82
52
2
84
54
2
Name
Default Value
Description
Temp High Alarm
Temp Low Alarm
Temp High Warning
Temp Low Warning
Voltage High Alarm
Voltage Low Alarm
Voltage High Warning
Voltage Low Warning
Bias High Alarm
Bias Low Alarm
Bias High Warning
Bias Low Warning
TX Power High Alarm
TX Power Low Alarm
TX Power High Warning
TX Power Low Warning
RX Power High Alarm
RX Power Low Alarm
RX Power High Warning
RX Power Low Warning
Reserved
RX_PWR(4) Calibration
RX_PWR(3) Calibration
RX_PWR(2) Calibration
RX_PWR(1) Calibration
RX_PWR(0) Calibration
TX_I(Slope) Calibration
TX_I(Offset) Calibration
TX_PWR(Slope) Calibration
TX_PWR(Offset) Calibration
T(Slope) Calibration
xx xxh
xx xxh
xx xxh
xx xxh
94 70h
6D 60h
8C A0h
75 30h
83 81h
02 64h
77 8Ch
03 96h
xx xxh
xx xxh
xx xxh
xx xxh
FF FFh
00 00h
FF FFh
00 00h
00….000h
xx xx xx xxh
xx xx xx xxh
xx xx xx xxh
xx xx xx xxh
xx xx xx xxh
01 A3h
00 00h
xx xxh
00 00h
01 00h
T(Offset) Calibration
xx xxh
Temperature high alarm threshold
Temperature low alarm threshold
Temperature high warning threshold
Temperature low warning threshold
3.8V
2.8V
3.6V
3.0V
110mA
2mA
100mA
3mA
+5.5 dBm
+0.5dBm
+5.0dBm
+1.0dBm
No alarm
No alarm
No alarm
No alarm
Reserved
4th order RSSI calibration coefficient
3rd order RSSI calibration coefficient
2nd order RSSI calibration coefficient
1st order RSSI calibration coefficient
0th order RSSI calibration coefficient
Slope for Bias calibration
Offset for Bias calibration
Slope for TX Power calibration
Offset for TX Power calibration
Slope for Temperature calibration
Offset for Temperature calibration, in units of
256ths C
Slope for VCC calibration
Offset for VCC calibration
reserved
Checksum
Temperature in C/256
Vcc
BIASMON
Back facet monitor
RSSI
Reserved
Reserved
Digital state of the TX Disable Input Pin.
86
56
2
88
90
92
95
96
98
100
102
104
106
108
58
5A
5C
5F
60
62
64
66
68
6A
6C
6E.7
2
2
3
1
2
2
2
2
2
2
2
1bit
V(Slope) Calibration
V(Offset) Calibration
Reserved
Checksum
Transceiver Temperature
Supply Voltage
TX Bias Current
TX Optical Output Power
RX Optical Input Power
Reserved
Reserved
TX_DIS State
01 00h
00 00h
00h
xxh
xx xxh
xx xxh
xx xxh
xx xxh
xx xxh
0000h
0000h
x
6E.6
1bit
Soft TX Disable
x
Read/write bit that allows software disable of
laser.
6E.5
6E.4
6E.3
6E.2
1bit
1bit
1bit
1bit
Reserved.
Rate Select State
Rate Select
TX_FAULT
0
0
0
x
Reserved.
NOT SUPPORTED.
NOT SUPPORTED.
Digital state of the TX Fault Output Pin.
6E.1
1bit
LOS
0
NOT SUPPORTED
6E.0
1bit
Data_ready_bar
x
Indicates transceiver has achieved power up
and data is ready.
110
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
6
LUMNDS2036-FEB1108
rev. 0.2 SHORT FORM
1490nm/1310nm Single Fiber OLT Transceiver
Preliminary Datasheet
SPS-43-48H-HP-xDE (x=C, R, T)
DEC
Addr.
HEX
Addr.
Field Size
(bytes)
Name
Default Value
Description
I2C A2h Address
6F.7
1bit
6F.6
1bit
6F.5
1bit
6F.4
1bit
111 6F.3
1bit
6F.2
1bit
6F.1
1bit
Reserved
Reserved
Reserved
Reserved
Reserved
INTERRUPT_NOT
MODE_EN
0
0
0
0
0
x
0
6F.0
1bit
APD_SHUTDOWN
x
70.7
70.6
70.5
70.4
70.3
70.2
70.1
70.0
71.7
71.6
71.5
71.4
71.3
71.2
71.1
71.0
72
73
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1
1
Temperature too high alarm
Temperature too low alarm
VCC too high alarm
VCC too low alarm
BIASMON too high alarm
BIASMON too low alarm
BFMON too high alarm
BFMON too low alarm
RSSI too high alarm
RSSI too low alarm
Reserved interrupt status bit
Reserved interrupt status bit
Reserved interrupt status bit
Reserved interrupt status bit
Reserved interrupt status bit
Reserved interrupt status bit
Reserved
Reserved
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
00h
00h
Reserved
Reserved
Reserved
Reserved
Reserved
Interrupt state (active low)
TX FAULT pin enable
APD shut-down latch. Write 0 to clear
condition
Temperature too high alarm
Temperature too low alarm
VCC too high alarm
VCC too low alarm
BIASMON too high alarm
BIASMON too low alarm
BFMON too high alarm
BFMON too low alarm
RSSI too high alarm
RSSI too low alarm
Reserved interrupt status bit
Reserved interrupt status bit
Reserved interrupt status bit
Reserved interrupt status bit
TX Fail went HIGH
APD Shutdown event detected
Interrupt Mask for ISRC0
Interrupt Mask for ISRC1
74.7
1bit
Temperature too high warning
x
Temperature too high warning
74.6
74.5
74.4
74.3
74.2
74.1
74.0
75.7
75.6
75.5
75.4
75.3
75.2
75.1
75.0
76
77
78
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1bit
1
1
8
Temperature too low warning
VCC too high warning
VCC too low warning
BIASMON too high warning
BIASMON too low warning
BFMON too high warning
BFMON too low warning
RX Power High Warning
RX Power Low Warning
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Vendor Specific
x
x
x
x
x
x
x
x
x
0
0
0
0
0
0
00h
00h
00 00 00 00 00 00 00 00h
Temperature too low warning
VCC too high warning
VCC too low warning
BIASMON too high warning
BIASMON too low warning
BFMON too high warning
BFMON too low warning
RSSI too high warning
RSSI too low warning
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Interrupt Mask for ISRC2
Interrupt Mask for ISRC3
Vendor Specific
112
113
114
115
116
117
118
119
120
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
7
LUMNDS2036-FEB1108
rev. 0.2 SHORT FORM
1490nm/1310nm Single Fiber OLT Transceiver
Preliminary Datasheet
SPS-43-48H-HP-xDE (x=C, R, T)
Outline Drawing
Units in inches (mm)
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
8
LUMNDS2036-FEB1108
rev. 0.2 SHORT FORM
1490nm/1310nm Single Fiber OLT Transceiver
Preliminary Datasheet
SPS-43-48H-HP-xDE (x=C, R, T)
Ordering informatio
Available Options:
SPS-43-48H-HP-CDE
n
SPS-43-48H-HP-RDE
SPS-43-48H-HP-TDE
��������������������������
���
����������������������������������������������������������������������������������������������������
��������������������������������������������
�
��������������
����������������
������������������������������������
���������������������������
������������������������������������������
������������������������������
�
�
���������������������������
����������������������������������
������������������������������������������������������
��������������������������
�
����������������������������������
�
�������������������������
Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow
guidelines according to proper ESD procedures.
Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation.
IMPORTANT NOTICE!
All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance
of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are
given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of
Sale for further warranty information.
LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual
property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes
no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers
using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from
such use or sale.
THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any
actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact
LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current.
© LuminentOIC, Inc. 2005
All rights reserved
LUMINENTOIC.COM
20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486
9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213
9
LUMNDS2036-FEB1108
rev. 0.2 SHORT FORM