1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Features • Burst receive PON OLT transceiver • “Fast Signal Detect” feature reduces ranging overhead • Simplifed OLT “reset” timing • Small Form Factor, 2 x 10 pigtailed bi-directional • 1490 nm DFB Tx with isolator • 1310 nm APD Rx • 2488 Mbps downstream Tx/1244 Mbps upstream Rx • Single 3.3 V supply • ITU-T G.984.2 compliant • 20 km reach; 28 dB link budget • SC/UPC fiber connector; IEC 61754-4 compliant • RoHS-5/6 compliant (lead exemption) Absolute Maximum Rating Parameter Symbol Min. Typ. Max. Unit Supply Voltage Vcc_MAX 0 - 3.6 V Operation Relative Humidity RHs 5 - 90 % Storage Temperature Tstg -40 - 85 ºC PIn_max +3 - - dBm TX_DIS_max 0 - Vcc+0.5 V Reset_max 0 - Vcc+0.5 V I2C Serial Data Logic High State SDAmax - - Vcc+0.5 V I2C Serial Clock Logic High State SCLmax - - Vcc+0.5 V Maximum Receiver Input Power TX Disable Logic High State RX Reset Logic High State General Operating Parameter Operating Voltage Symbol Min. Typ. Max. Unit Vcc 3.135 3.3 3.465 V Total Supply Current ICC - - 450 mA Case Operating Temerature (-CDE) Topr -5 - 70 ºC Case Operating Temerature (-RDE) Topr -20 - 85 ºC Case Operating Temerature (-TDE) Topr -40 - 85 ºC Storage Temperature Tstg -40 - 85 ºC Symbol General Optical Parameters Parameter Min. Typ. Max. Unit Back Reflection at 1490 nm - - -20 dB Back Reflection at 1310 nm - - -20 dB 1490 nm to 1310 nm crosstalk - - -45 dB LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 1 LUMNDS995-APR0207 Rev A.0 SHOR T FORM 1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Transmitter Specifications (Optical) Parameter Symbol Min Typical Max Unit Optical Power Pop 1.5 - 5 dBm Average launch power of off Tx Poff - - -40 dBm λ 1480 1490 1500 nm ∆λ20 - - 1 nm SMSR 30 - - dB ER 10 - - dB Wavelength Spectral Width (-20 dB) Side Mode Suppression Ratio Extinction Ratio G.984.2 Transmit eye mask - 2488 - Mbps 72 - - bits Optical Rise timea - - 160 ps timea - - 160 ps - - 0.5 dB -15 - Symbol Min Typical Max Unit Rin 80 100 120 Ω Vin, p-p 300 - 1200 mV Vd 2 - Vcc V Ven 0 - 0.8 V V_Fail 2.4 0 - Vcc 0.4 V V Downstream Bit Rate +/- 100ppm Transmitter CID immunity Optical Fall Optical Path Penalty Tolerence to TX back reflectionb dB a) 20% to 80% values b) 1 dB degradation of receiver sensitivity Transmitter Specifications (Electrical) Parameter Input Differential Impedence Single Ended data input swing (ac coupled inside module) Tx Disable (LVTTL) Tx Enable (LVTTL) Tx_Fail_High (LVTTL) Tx_Fail_Normal (LVTTL) V_Normal Receiver Specifications (Optical) Parameter Symbol Min Typical Max Unit Wavelength λ 1260 1310 1360 nm Upstream Data Rate +/- 100ppm (burst-mode) - 1244 - Mbps Receiver Sensitivityc RENS - -31 -28 dBm Receiver Overloadc ROL -8 -5 - dBm 15 20 - dB P_DET CID - - -28 dBm 72 - - bits RX_r - - -20 dB Receiver Burst-mode Dynamic Ranged BRST_Det Assert (Signal Detected) Receiver CID Tolerance Maximum Reflectance of Receiver c) At 10-10 BER with PRBS 223-1 Burst-Mode data at 1244 Mb/s d) The input power difference between two subsequent high and low burst data. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 2 LUMNDS995-APR0207 Rev A.0 SHOR T FORM 1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Receiver Specifications (Electrical) Parameter Symbol Min Typical Max Unit PECL Single ended data output swing(LVPECL) Vout,p-p 250 - 800 mV tr - 250 - ps tf - 250 - ps BRST_Det_High V_DETH 2.4 - Vcc V BRST_Det_Lowf V_DETL 0 - 0.4 V BRST_Det Response Time T_BRST_Det - - 6.4 nS Reset Input Timingg T_Reset_start -0.5 0 +1 Byte Reset Input Duration T_Reset 2 - - Byte T_chatter 300 - - nS Data output rise timee Data output fall timee f RX output chatter time constanth e) 20% to 80% values f) BRST_Det assert low when module receive “reset” signal, assert high when incoming burst is detected and latch to high state until next “Reset” signal. g) Timing for rising edge of “Reset” input singal is referenced to module pins with assumption of 4 bytes guard time after previous burst end h) RX output will start to chatter after T_chatter if there is no optical input or reset signal present. I2C Serial Logic & Digital Diagnostic Monitor (DDM) Parameter Symbol Min Typical Max Unit I2C Serial Data High VSDA_H 2.0 - Vcc V I2C Serial Data Low VSDA_L 0 - 0.8 V I2C Serial Clock High VSCL_H 2.0 - Vcc V I2C Serial Clock Low VSCL_L 0 - 0.8 V TX Power DDM Error TXDDM - - +/- 3 dBm Case Temperature DDM Error TX Bias DDM Error Vcc DDM Error LUMINENTOIC.COM TDDM - - +/- 5 ºC TXBIASDDM - - +/- 10 mA VCCDDM - - +/- 0.3 V 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 3 LUMNDS995-APR0207 Rev A.0 SHOR T FORM 1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE EEPROM Pin Function Notes 1 Reset CMOS input. Assert “Reset” high at the end of previous burst, 2 bytes in duration 2 Pmon_analog Analog signal output for receiver optical input power monitoring 3 RX_GND Rx Ground 4 Reserved No User Connection; Internal use 5 6 Reserved RX_GND No User Connection; Internal use Rx Ground 7 RX_Vcc Rx Vcc BRST_Det LVTTL output. BRST_Det assert low when module receives “reset” signal, assert high when incoming burst is present. 8 9 RXD- Negative Data Output, LVPECL; DC coupled 10 RXD+ Positive Data Output, LVPECL; DC coupled 11 TX_Vcc Tx Vcc 12 TX_GND 13 TX_DIS 14 TXD+ 15 TXD- Tx Ground Tx Disable. LVTTL input. Laser output is disabled when this pin is asserted high or left unconnected. Laser output is enabled when this pin is asserted low. Positive Data Input, LVPECL or CML (AC coupled; internally 100 ohms differential termination) Negative Data Input, LVPECLor CML (AC coupled; internally 100 ohms differential termination) 16 TX_GND Tx Ground 17 SCL 2-Wire Serial Clock Input. Clocks data into and out of the device. 18 SDA 2-Wire Serial Data I/O Pin. Transfers serial data to and from the device. 19 TX_FAIL Tx Fail Alarm. LVTTL Output Active high. 20 TX_GND Tx Ground LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 4 LUMNDS995-APR0207 Rev A.0 SHOR T FORM 1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Timing Diagram Detailed burst-mode receiver timing diagram is available upon request. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 5 LUMNDS995-APR0207 Rev A.0 SHOR T FORM 1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE EEPROM Content DEC Addr. HEX Addr. Field Size (bytes) Name Default Value Description I2C A0h Address 0 00 1 1 01 1 2 02 1 3 03 8 11 0B 1 12 0C 1 13 0D 1 14 0E 1 15 0F 1 16 10 1 17 11 1 18 12 1 19 13 1 20 14 16 36 24 1 37 25 3 40 28 16 56 38 4 60 3C 2 62 3E 1 Identifier Extended Identifier Connector Transceiver Encoding Nominal Bit Rate in 100 MBps Reserved Length (9µ, km) in km Length (9µ, m) in 100 m Length (50µ) in 10 m Length (62.5µ) in 10 m Length (Copper) in m Reserved Vendor Name (ASCII) Reserved Vender IEEE Company ID Vendor Part Number (ASCII) Vendor Rev (ASCII) Laser Wavelength in nm Reserved 02h 04h 0Bh (pigtail). 00 00 00 00 00 00 00 00h 03h 19h 00h 14h C8h 00h 00h 00h 00h "LUMINENTOIC " 00h 00 06 B5h "SFU4348HHPxDExxx" 31 20 20 20 05 D2h 00h Module soldered to motherboard Function defined by serial ID Optical pigtail Transceiver Code Field, not applicable NRZ encoding 2488.32 Mbps Reserved 20km 20km Not Supported Not Supported Not Supported Reserved Vendor Name (ASCII) Reserved LuminentOIC IEEE ID Vendor Part Number (ASCII) Revision 1490nm Tx Wavelength Reserved 63 3F 1 Check Code for Base ID Fields xxh Checksum from byte 0-62 64 66 67 68 40 42 43 44 2 1 1 16 Options Upper Bit Rate Margin in % Lower Bit Rate Margin in % Vendor Serial Number (ASCII) 00 1Ch 00h 00h "xxxxxxxxxxxxxxxx" TX_DIS, TX_Fault, SD BR, Max not specified BR, Min not specified 16 byte Serial number field (ASCII) 84 54 8 Date Code xx xx xx xx xx xx 20 20h Year(2 bytes) month(2 bytes) day(2 bytes) 92 5C 1 Diagnostic Monitoring Type 58h Ext Calibration, Average Power Measurement 93 5D 1 Enhanced Options E0h 94 5E 1 02h 95 5F 1 SFF-8472 Compliance Check Code for Extended ID Fields Optical Alarm/warning implemented Soft TX_DIS, TX_FAULT implemented Compliance to SFF-8472 Rev 9.4 xxh Checksum from byte 64-69 96 60 30 Vendor Specific "SFU-43-48H-HP-xDE-xx " LOIC part number (ASCII) 126 7E 2 Vendor Specific 0C 83h 128 80 128 Reserved 00….00h Upstream Bit Rate (100 Mbps units) and Receive Wavelength (10 nm units) Reserved; return to 0 For detailed specifications of EEPROM contents and externally calibrated digital diagnostic monitor (DDM) functions, please refer to SFF-8472 standard Rev 9.5. LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 6 LUMNDS995-APR0207 Rev A.0 SHOR T FORM 1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE DEC Addr. HEX Addr. Field Size (bytes) I2C A2h Address 0 00 2 2 02 2 4 04 2 6 06 2 8 08 2 10 0A 2 12 0C 2 14 0E 2 16 10 2 18 12 2 20 14 2 22 16 2 24 18 2 26 1A 2 28 1C 2 30 1E 2 32 20 2 34 22 2 36 24 2 38 26 2 40 28 16 56 38 4 60 3C 4 64 40 4 68 44 4 72 48 4 76 4C 2 78 4E 2 80 50 2 82 52 2 84 54 2 Name Default Value Description Temp High Alarm Temp Low Alarm Temp High Warning Temp Low Warning Voltage High Alarm Voltage Low Alarm Voltage High Warning Voltage Low Warning Bias High Alarm Bias Low Alarm Bias High Warning Bias Low Warning TX Power High Alarm TX Power Low Alarm TX Power High Warning TX Power Low Warning RX Power High Alarm RX Power Low Alarm RX Power High Warning RX Power Low Warning Reserved RX_PWR(4) Calibration RX_PWR(3) Calibration RX_PWR(2) Calibration RX_PWR(1) Calibration RX_PWR(0) Calibration TX_I(Slope) Calibration TX_I(Offset) Calibration TX_PWR(Slope) Calibration TX_PWR(Offset) Calibration T(Slope) Calibration xx xxh xx xxh xx xxh xx xxh 94 70h 6D 60h 8C A0h 75 30h 83 81h 02 64h 77 8Ch 03 96h xx xxh xx xxh xx xxh xx xxh FF FFh 00 00h FF FFh 00 00h 00….000h xx xx xx xxh xx xx xx xxh xx xx xx xxh xx xx xx xxh xx xx xx xxh 01 A3h 00 00h xx xxh xx xxh 01 00h T(Offset) Calibration xx xxh 80C (-CDE); 92C(-RDE); 92C(-TDE) -13C(-CDE);-28(-RDE);-48C(-TDE) 75C(-CDE); 87C(-RDE); 87C(-TDE) -8C(-CDE); -23C(-RDE); -43C(-TDE) 3.8V 2.8V 3.6V 3.0V 110mA 2mA 100mA 3mA +5.5 dBm +0.5dBm +5.0dBm +1.0dBm No alarm No alarm No alarm No alarm Reserved 4th order RSSI calibration coefficient 3rd order RSSI calibration coefficient 2nd order RSSI calibration coefficient 1st order RSSI calibration coefficient 0th order RSSI calibration coefficient Slope for Bias calibration Offset for Bias calibration Slope for TX Power calibration Offset for TX Power calibration Slope for Temperature calibration Offset for Temperature calibration, in units of 256ths C Slope for VCC calibration Offset for VCC calibration reserved Checksum Temperature in C/256 Vcc BIASMON Back facet monitor RSSI Reserved Reserved Digital state of the TX Disable Input Pin. 86 56 2 88 90 92 95 96 98 100 102 104 106 108 58 5A 5C 5F 60 62 64 66 68 6A 6C 6E.7 2 2 3 1 2 2 2 2 2 2 2 1bit V(Slope) Calibration V(Offset) Calibration Reserved Checksum Transceiver Temperature Supply Voltage TX Bias Current TX Optical Output Power RX Optical Input Power Reserved Reserved TX_DIS State 01 00h 00 00h 00h xxh xx xxh xx xxh xx xxh xx xxh xx xxh 0000h 0000h x 6E.6 1bit Soft TX Disable x 6E.5 6E.4 6E.3 6E.2 1bit 1bit 1bit 1bit Reserved. Rate Select State Rate Select TX_FAULT 0 0 0 x 6E.1 1bit LOS 0 6E.0 1bit Data_ready_bar x 110 LUMINENTOIC.COM Read/write bit that allows software disable of laser. Reserved. NOT SUPPORTED. NOT SUPPORTED. Digital state of the TX Fault Output Pin. Digital state of the LOS Output Pin. NOT SUPPORTED Indicates transceiver has achieved power up and data is ready. 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 7 LUMNDS995-APR0207 Rev A.0 SHOR T FORM 1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE DEC Addr. HEX Addr. Field Size (bytes) Name Default Value Description I2C A2h Address 6F.7 1bit 6F.6 1bit 6F.5 1bit 6F.4 1bit 111 6F.3 1bit 6F.2 1bit 6F.1 1bit Reserved Reserved Reserved Reserved Reserved INTERRUPT_NOT MODE_EN 0 0 0 0 0 x 0 6F.0 1bit APD_SHUTDOWN x 70.7 70.6 70.5 70.4 70.3 70.2 70.1 70.0 71.7 71.6 71.5 71.4 71.3 71.2 71.1 71.0 72 73 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1 1 Temperature too high alarm Temperature too low alarm VCC too high alarm VCC too low alarm BIASMON too high alarm BIASMON too low alarm BFMON too high alarm BFMON too low alarm RSSI too high alarm RSSI too low alarm Reserved interrupt status bit Reserved interrupt status bit Reserved interrupt status bit Reserved interrupt status bit Reserved interrupt status bit Reserved interrupt status bit Reserved Reserved x x x x x x x x x x x x x x x x 00h 00h Reserved Reserved Reserved Reserved Reserved Interrupt state (active low) TX FAULT pin enable APD shut-down latch. Write 0 to clear condition Temperature too high alarm Temperature too low alarm VCC too high alarm VCC too low alarm BIASMON too high alarm BIASMON too low alarm BFMON too high alarm BFMON too low alarm RSSI too high alarm RSSI too low alarm Reserved interrupt status bit Reserved interrupt status bit Reserved interrupt status bit Reserved interrupt status bit TX Fail went HIGH APD Shutdown event detected Interrupt Mask for ISRC0 Interrupt Mask for ISRC1 74.7 1bit Temperature too high warning x Temperature too high warning 74.6 74.5 74.4 74.3 74.2 74.1 74.0 75.7 75.6 75.5 75.4 75.3 75.2 75.1 75.0 76 77 78 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1bit 1 1 8 Temperature too low warning VCC too high warning VCC too low warning BIASMON too high warning BIASMON too low warning BFMON too high warning BFMON too low warning RX Power High Warning RX Power Low Warning Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Vendor Specific x x x x x x x x x 0 0 0 0 0 0 00h 00h 00 00 00 00 00 00 00 00h Temperature too low warning VCC too high warning VCC too low warning BIASMON too high warning BIASMON too low warning BFMON too high warning BFMON too low warning RSSI too high warning RSSI too low warning Reserved Reserved Reserved Reserved Reserved Reserved Interrupt Mask for ISRC2 Interrupt Mask for ISRC3 Vendor Specific 112 113 114 115 116 117 118 119 120 LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 8 LUMNDS995-APR0207 Rev A.0 SHOR T FORM 1490nm/1310nm Single Fiber OLT Transceiver SFU-43-48H-HP-xDE Outline Drawing 12.70 .500 13.97 .550 3.04 .120 TYP 1.02 2X .040 0.51 0.46 .020 .018 4.98 .196 40.13 1.580 12.45 .490 TABS PIN 10 PIN 1 5.94 .234 1.27 .050 .010 .005 0.25 .010 10.16 .400 PIN 20 8.89 .350 30.28 1.192 [1000 100] 39.370 3.937 LUMINENTOIC.COM +0.25 12.70 0 +.010 .500 - .000 3.56 .140 D E TA I L A SCALE 8 : 1 1.78 .070 PIN 11 4 PLACES 16 .630 50.09 1.972 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 9 LUMNDS995-APR0207 Rev A.0 SHOR T FORM 1490nm/1310nm Single Fiber SFFB Transceiver SFU-43-48H-HP-xDE Ordering informatio n Order Option: SFU-43-48H-HP-CDE n SFU-43-48H-HP-RDE SFU-43-48H-HP-TDE �������������������������� ��� ���������������������������������������������������������������������������������������������������� ����������������������������������������� � ���������������� ���������������� ������������������������������������ ��������������������������� ������������������������������������������ ������������������������������ � ���������������������������� ���������������������������������� ������������������������������������������������������ � � ���������������������������������� ������������������������� Handling Precautions: This device is susceptible to damage as a result of electrostatic discharge (ESD). A static free environment is highly recommended. Follow guidelines according to proper ESD procedures. Laser Safety: Radiation emitted by laser devices can be dangerous to human eyes. Avoid eye exposure to direct or indirect radiation. IMPORTANT NOTICE! All information contained in this document is subject to change without notice, at LuminentOIC’s sole and absolute discretion. LuminentOIC warrants performance of its products to current specifications only in accordance with the company’s standard one-year warranty; however, specifications designated as “preliminary” are given to describe components only, and LuminentOIC expressly disclaims any and all warranties for said products, including express, implied, and statutory warranties, warranties of merchantability, fitness for a particular purpose, and non-infringement of proprietary rights. Please refer to the company’s Terms and Conditions of Sale for further warranty information. LuminentOIC assumes no liability for applications assistance, customer product design, software performance, or infringement of patents, services, or intellectual property described herein. No license, either express or implied, is granted under any patent right, copyright, or intellectual property right, and LuminentOIC makes no representations or warranties that the product(s) described herein are free from patent, copyright, or intellectual property rights. Products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. LuminentOIC customers using or selling products for use in such applications do so at their own risk and agree to fully defend and indemnify LuminentOIC for any damages resulting from such use or sale. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN “AS IS” BASIS. Customer agrees that LuminentOIC is not liable for any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the information contained in this document. Customer must contact LuminentOIC to obtain the latest version of this publication to verify, before placing any order, that the information contained herein is current. © LuminentOIC, Inc. 2005 All rights reserved LUMINENTOIC.COM 20550 Nordhoff St. • Chatsworth, CA 91311 • tel: 818.773.9044 • fax: 818.576.9486 9F, No 81, Shui Lee Rd. • Hsinchu, Taiwan, R.O.C. • tel: 886.3.5169222 • fax: 886.3.5169213 10 LUMNDS995-APR0207 Rev A.0 SHOR T FORM