SA5.0 - SA180CA Transient Voltage Suppressors FEATURES Peak Pulse Power 500W Stand Off Voltage 5.0 to 180V Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Glass passivated junction Excellent clamping capability Low incremental surge resistance Very fast response time 500W peak pulse power surge capability with a 10/100us waveform, repetition rate (duty cycle): 0.01% High temperature soldering guaranteed: 265oC/10 seconds, 0.375" (9.5mm) lead length, 5lbs. (2.3kg) tension MECHANICAL DATA Case: JEDEC DO-204AC(DO-15) molded plastic body over passivated junction Terminals: Solder plated axial leads, solder-able per MILSTD-750, Method 2026 Polarity: For unidirectional types the color band denotes the cathode, which is positive with respect to the anode under normal TVS operation Mounting Position: Any Weight: 0.015oz., 0.4g Pb-free; RoHS-compliant 01/10/2007 Rev. 1.00 www.SiliconStandard.com 1 SA5.0 - SA180CA MAXIMUM RATINGS (TA=25℃ unless otherwise specified) Parameter Peak pulse power dissipation with a 10/1000us waveform (1) (Fig. 1) Peak pulse current with (1) a 10/1000us waveform Steady state power dissipation at TA =75℃ lead lengths, 0.375" (9.5mm) (2) Peak forward surge current, 10ms single half sine-wave unidirectional only Maximum instantaneous forward voltage at 35A for unidirectional only Operating junction and storage temperature range NOTE: Symbol Value Unit PPPM 500 (Min.) W IPPM See Next Table A PM(AV) 3.0 W IFSM 70 A VF 3.5 Volts TJ, TSTG -55 to +175 ℃ 1. Non-repetitive current pulse, per Fig. 3 and derated above TA=25℃ per Fig. 2. 2. Mounted on copper pad area of 1.6 x 1.6" (40 x 40mm) per Fig. 5. 3. 8.3ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum. 01/10/2007 Rev. 1.00 www.SiliconStandard.com 2 SA5.0 - SA180CA ELECTRICAL CHARACTERISTICS (TA = 25°C , unless otherwise specified.) A 01/10/2007 Rev. 1.00 www.SiliconStandard.com 3 SA5.0 - SA180CA ELECTRICAL CHARACTERISTICS (TA = 25°C , unless otherwise specified.) A NOTE: 1. V(BR) measured after IT applied for 300us. IT=square wave pulse or equivalent 2. Surge current waveform per Fig. 3 and derate per Fig. 2 3. For bidirectional types with VWM of 10 Volts and less, the ID limit is doubled 4. For the bidirectional SA5.0CA, the maximum VBR is 7.25V 5. All terms and symbols are consistent with ANSI/IEEE C62.35 6. For parts without A, the VBR is +10% 01/10/2007 Rev. 1.00 www.SiliconStandard.com 4 SA5.0 - SA180CA RATINGS AND CHARACTERISTIC CURVES (TA = 25°C , unless otherwise specified.) 01/10/2007 Rev. 1.00 www.SiliconStandard.com 5 SA5.0 - SA180CA RATINGS AND CHARACTERISTIC CURVES (TA = 25°C , unless otherwise specified.) 01/10/2007 Rev. 1.00 www.SiliconStandard.com 6 SA5.0 - SA180CA RATINGS AND CHARACTERISTIC CURVES (TA = 25°C , unless otherwise specified.) 01/10/2007 Rev. 1.00 www.SiliconStandard.com 7 SA5.0 - SA180CA Disclaimer Information furnished by Silicon Standard Corporation is believed to be accurate and reliable. However, Silicon Standard Corporation makes no guarantee or warranty, expressed or implied, as to the reliability, accuracy, timeliness or completeness of such information and assumes no responsibility for its use, or for infringement of any patent or other intellectual property rights of third parties that may result from its use. Silicon Standard reserves the right to make changes as it deems necessary to any products described herein for any reason, including without limitation enhancement in reliability, functionality or design. No license is granted, whether expressly or by implication, in relation to the use of any products described herein or to the use of any information provided herein, under any patent or other intellectual property rights of Silicon Standard Corporation or any third parties. 01/10/2007 Rev. 1.00 www.SiliconStandard.com 8