SpectrAlert™ Colored Lens Strobes and Horn/Strobes Models Available* Strobes Red S2475RLP S2475ALP S2475GLP S2475BLP White S2475RLPW S2475ALPW S2475GLPW S2475BLPW Horn/Strobes Red P2475RLP P2475ALP P2475GLP P2475BLP White P2475RLPW P2475ALPW P2475GLPW P2475BLPW Accessories Red S-MP BBS White S-MPW BBSW Product Overview Available with red, amber, green, or blue lens Meets UL 1638 (Private Mode) requirements Strobes & Horn/Strobes operate at 24 volts Low current draw Field-selectable horn tones Universal mounting plate included Accessory mounting plates available Synchronizable with Sync•Circuit™ module SpectrAlert Colored Lens series strobes and horn/strobes provide many of the same benefits as the original SpectrAlert design, but with the choice of colored lenses for signaling differentiation. Intended for private mode applications, the Colored Lens strobe and horn/strobe meet UL 1638, ‘Private Mode Emergency and General Utility Signaling’. Flexibility. SpectrAlert Colored Lens products are designed for use in niche applications not requiring UL 1971 notification devices. SpectrAlert strobes and horn/strobes are offered with red, amber, green, and blue lenses for use in special alarm systems such as gas alarms, suppression systems, non-fire applications requiring evacuation signaling, and as warning, trouble, or identification signals. Performance. The low current draw of SpectrAlert products helps minimize power supply requirements. By consuming less current, the flexibility to connect more devices per loop is possible, for a lower installed cost. Installation. SpectrAlert products are easy to use, to help reduce installation costs. Each SpectrAlert includes a universal mounting plate for 4″ square and single gang back box mounting. Accessory mounting plates are also available for small footprint or surface-mount applications. Engineering Specifications General SpectrAlert strobes and horn/strobes shall be capable of mounting to a standard 4″×4″×11⁄2″ back box or a single gang 2″×4″×17⁄8″ back box using the universal mounting plate included with each SpectrAlert product. Strobes and Horn/Strobes shall have a light output of 75 candela, per UL 1638, and shall have an operating voltage range of 20–30 volts. SpectrAlert products shall have an operating temperature of 32° to 120°F. and operate from a regulated DC or full wave rectified, unfiltered power supply. SpectrAlert products, when used in conjunction with the accessory Sync•Circuit Module, shall be powered from a non-coded power supply and shall operate on 24 volts. Horn/Strobe Combination Horn/Strobe shall be a System Sensor SpectrAlert Model _____ listed to UL 1638 and UL 464, and the flash rate shall be 1 Hz over the strobe’s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. The horn shall have two tone options, two audibility options and the option to switch between a temporal 3 pattern and a non-temporal continuous pattern. Strobes shall be powered independently of the sounder with the removal of factory installed jumper wires. The horn on horn/strobe models shall operate on a coded or non-coded power supply (the strobe must be powered continuously for the horn to operate). Strobe Strobe shall be a System Sensor SpectrAlert Model _____ listed to UL 1638, flashing at 1 Hz over the strobe’s entire operating voltage range. The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Specifications Input Terminals 12 to 18 AWG Dimensions Strobe or Horn/Strobe with universal mounting plate: 5″×55⁄8″×25⁄16″ Strobe or Horn/Strobe with small footprint plate: 33⁄8″×55⁄8″×25⁄16″ Weight 7.2 oz. Mounting 4″×4″ or 2″×4″ standard backboxes Operating Temperature 32°F to 120°F. Voltages 24 VDC and FWR unfiltered Operating Voltage Range* 24V: 20–30V Operating Voltage Range* 24V, 21–30V (with Sync-Circuit module, MDL) *These products should be operated within their rated voltage range; UL does, however, test functional integrity to –20% and +10% of manufacturer’s stated ranges. Horn/Strobe Sound Output Electromechanical Tone Volume High Tone Temp Non Low Temp Non 3000 Hz Interrupted Tone Volume High Low Tone Temp Non Temp Non UL Reverberant Room dBA @ Volts DC 24 82 88 75 82 UL Reverberant Room dBA @ Volts DC 24 85 88 79 82 Anechoic Room Peak dBA @ 10 ft./Volts DC 24 101 101 96 96 Anechoic Room Peak dBA @ 10 ft./Volts DC 24 101 101 96 96 Ordering Information Strobes Horn/Strobes* Sync•Circuit Model Number Small Footprint Mounting Plate Sur face Mount Back Box Skir t Universal Mounting Plate (Replacement) Red S2475RLP S2475ALP S2475GLP S2475BLP P2475RLP P2475ALP P2475GLP P2475BLP MDL S-MP BBS D-MP White S2475RLPW S2475ALPW S2475GLPW S2475BLPW P2475RLPW P2475ALPW P2475GLPW P2475BLPW MDLW S-MPW BBSW D-MPW Lens Color Red Amber Green Blue Red Amber Green Blue NA NA NA NA Voltage 24 24 24 24 24 24 24 24 12/24 NA NA NA Candela 75 75 75 75 75 75 75 75 NA NA NA NA Avg. mA @24 VDC 140 140 140 140 165 165 165 165 10/11 NA NA NA Avg. mA @24 VFWR 191 191 191 191 209 209 209 209 12/15 NA NA NA *Horn/strobe current draws reflect factor y setting of temporal 3, electromechanical tone, high audibility. System Sensor Sales and Service System Sensor Headquarters 3825 Ohio Avenue St. Charles, IL 60174 Ph: 800-SENSOR2 Fx: 630/377-6495 Documents On Demand: 1-800-736-7672 x3 Web: www.systemsensor.com System Sensor in Canada Ph: 905.812.0767 Fx: 905.812.0771 System Sensor in China Ph: + 86.29.524.6253 Fx: + 86.29.524.6259 System Sensor in Europe Ph: + 44.1403.276500 Fx: + 44.1403.276501 System Sensor in Singapore Ph: + 65.273.2230 Fx: + 65.273.2610 © 2000 System Sensor. The company reserves the right to change product specifications without notice. System Sensor in the Far East Ph: + 852.21919003 Fx: + 852.27366580 System Sensor in India Ph: + 91.11.558.2119 Fx: + 91.11.567.6815 System Sensor in Australia Ph: + 613.54.281.142 Fx: + 613.54.281.172 A05-0293-000•9/00(10K)•#667