WJCI AH2

AH2
The Communications Edge TM
Product Information
High Dynamic Range Amplifier
Product Features
x 50 – 1000 MHz
x +40 dBm OIP3
x -71dBc CTB
x -48dBc CSO
x 3.5 dB Noise Figure
x 14.5 dB Gain
x +20 dBm P1dB
x Lead-free/Green/RoHS-compliant
SOT-89 Package
x Single +5 V Supply
x MTTF > 100 years
Product Description
Functional Diagram
The AH2 is a general purpose, high dynamic range
amplifier targeting cable TV markets. The combination of
gain flatness, high linearity and bandwidth make it ideal for
CATV distribution, cable modem and laser diode driver
applications. The AH2 is designed for 75 ohm systems and
can operate directly from a +5 Volt DC regulator. The
device is manufactured using reliable GaAs MESFET
technology and boasts an MTBF of >100 years at a
mounting temperature of +85 °C. It is available in the
environmentally-friendly lead-free/green/RoHS-compliant
SOT-89 package. All devices are 100% RF and DC tested.
GND
4
1
2
3
RF IN
GND
RF OUT
Function
Input
Output/Bias
Ground
Pin No.
1
3
2, 4
Applications
x CATV / DBS
Specifications (1)
Parameter
Typical Performance (3)
Units
Min
MHz
MHz
dB
dB
dB
dBm
dBm
dB
mA
V
50
Operational Bandwidth
Test Frequency
Gain
Input Return Loss
Output Return Loss
Output P1dB
Output IP3 (2)
Noise Figure
Operating Current Range
Supply Voltage
13
+37
120
Typ
800
14.5
14
17
+21
+40
3.5
150
5
Max
Parameter
Units
1000
Frequency
S21
S11
S22
Output P1dB
Output IP3 (2)
Output IP2 (2)
CTB (4)
CSO (4)
Xmod (4)
Noise Figure
Supply Voltage
Device Current
MHz
dB
dB
dB
dBm
dBm
dBm
dBc
dBc
dBc
dB
V
mA
180
1. Test conditions unless otherwise noted: T = 25 ºC, 50 system.
2. 3OIP measured with two tones at an output power of +5 dBm/tone separated by 10 MHz. The
suppression on the largest IM3 product is used to calculate the 3OIP using a 2:1 rule.
Typical
100
14.5
-14
-17
+20
+40
+52
-71
-48
-65
3.5
860
13.2
-14
-17
+20
+40
+52
3.5
5
150
3. Parameters reflect performance in a single-ended 75 ohm circuit, as shown on page 3.
4. 77 channels 50 – 550MHz +34dBmV/channel, flat-loading
Absolute Maximum Rating
Parameter
Operating Case Temperature
Storage Temperature
Supply Voltage
RF Input Power (continuous)
Junction Temperature
Rating
-40 to +85 qC
-55 to +150 qC
+6 V
+10 dBm
+220 qC
Ordering Information
Part No.
Description
AH2-G
High Dynamic Range Amplifier
AH2-PCB
Single-ended 75 ohm Application Circuit Board
(lead-free/green/RoHS-compliant SOT-89 package)
Operation of this device above any of these parameters may cause permanent damage.
Specifications and information are subject to change without notice.
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: [email protected]
Web site: www.wj.com
Page 1 of 5 April 2006
AH2
The Communications Edge TM
Product Information
High Dynamic Range Amplifier
Typical Device Data
S-Parameters (VDS = +5 V, IDS = 150 mA, T = 25 C, unmatched device in a 75 ohm system)
S-Parameters (VD = +5 V, ID = 150 mA, T = 25 C, calibrated to device leads in a 75 ohm system)
Freq (MHz)
50
100
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
S11 (dB)
S11 (ang)
S21 (dB)
S21 (ang)
S12 (dB)
-17.85
-18.10
-17.37
-16.63
-15.73
-14.91
-14.20
-13.45
-12.80
-12.18
-11.53
-11.04
-10.51
-10.02
-9.64
-9.22
-8.81
-8.48
-8.11
-7.81
-34.21
-38.37
-47.65
-55.66
-62.92
-70.31
-76.37
-81.85
-86.94
-91.91
-95.72
-99.60
-103.27
-106.94
-110.30
-113.34
-116.55
-119.17
-121.84
-124.91
14.88
14.92
14.89
14.74
14.86
14.61
14.64
14.62
14.60
14.53
14.34
14.26
14.19
14.10
14.02
13.96
13.83
13.69
13.54
13.44
172.97
171.11
168.59
165.97
162.85
160.05
157.30
154.45
151.27
148.33
146.02
143.33
140.39
137.75
134.99
132.29
129.84
127.70
125.28
122.82
-24.58
-24.56
-24.55
-24.53
-24.48
-24.45
-24.42
-24.34
-24.31
-24.32
-24.21
-24.18
-24.12
-24.11
-24.02
-23.93
-23.89
-23.85
-23.81
-23.77
S12 (ang)
4.81
2.30
1.69
1.17
0.72
0.58
0.44
0.16
-0.28
-0.47
-0.94
-1.00
-1.10
-1.54
-2.04
-2.63
-3.12
-3.33
-4.08
-4.42
S22 (dB)
S22 (ang)
-20.87
-21.20
-21.20
-20.82
-20.50
-20.36
-19.77
-19.23
-19.02
-18.49
-17.96
-17.84
-17.56
-16.97
-16.69
-16.42
-16.13
-15.87
-15.59
-15.42
-149.34
-158.61
-160.06
-159.44
-156.95
-155.78
-155.09
-152.65
-152.33
-151.93
-149.07
-148.36
-149.69
-149.32
-148.96
-148.88
-149.30
-149.09
-149.60
-150.68
Device S-parameters are available for download off of the website at: http://www.wj.com
Input / Output Return Loss & Isolation
Gain
15
-5
S11
S12
14
S22
-10
S21 (dB)
Magnitude (dB)
0
-15
-20
13
12
11
-25
-30
10
0
200
400
600
800
1000
0
200
400
Frequency (MHz)
600
800
1000
Frequency (MHz)
Specifications and information are subject to change without notice.
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: [email protected]
Web site: www.wj.com
Page 2 of 5 April 2006
AH2
The Communications Edge TM
Product Information
High Dynamic Range Amplifier
Single – Ended CATV 75 : Evaluation Circuit: 50 – 860 MHz (AH2-PCB)
CAP
+5 V ID=C4
C=1000 pF
Typical RF Performance at 25 qC
Frequency
S21 – Gain
S11 – Input R.L.
S22 – Output R.L.
Output IP2
MHz 100
dB
14.5
dB -11.1
dB
-9.5
450 860
14.5 13.2
-12.7 -18.3
-22.9 -10.6
dBm
52.7
53.5
52.5
Output IP3
dBm
39.8
40.7
40.8
(+5 dBm)
(+5 dBm / tone, 10 MHz spacing)
IND
ID=L3
L=270 nH
CAP
ID=C1
C=1000 pF
PORT
P=1
Z=75 Ohm
SUBCKT
ID=S1
NET="AH2"
IND
ID=L1
L=12 nH
CAP
ID=C3
C=1000 pF
PORT
P=2
Z=75 Ohm
CAP
ID=C2
C=2.2 pF
dB
Noise Figure
3.9
3.1
3.2
Device Bias
+5V @ 150mA
CTB
dBc
-71
CSO
dBc
-48
XMOD
dBc
-65
77 channels, 50-550MHz, +34dBmV/channel flat loading
Circuit Board Material: .062” total thickness with a .028” FR-4 top RF layer, 4 layers (other
layers added for rigidity), 1 oz copper, 75 Microstrip.
Linearity vs. Frequency
Input / Output ReturnLoss
andIsolation
15.5
S22
-10
30
OIP3
OIP2
20
0
0
200
400
600
800
1000
S11
-30
0
200
-70
CTB
-80
400
0
1000
200
400
500
600
600
800
1000
Frequency(MHz)
IP2 and IP3 vs. Power Out at 450 MHz
55
Intercept Point (dBm)
dBc
XMOD
Noise Figure (dB)
-60
300
800
5
CSO
-50
200
600
NoiseFigure
77Channel Flat Loading, +34dBmV/Ch.
100
400
S21-40C S2125C S2185C
13
Frequency(MHz)
CTB, CSO, andXMODVs. Frequency
0
14
13.5
S12
Frequency (MHz)
-40
15
14.5
-20
10
Magnitude (dB)
40
Gain
16
0
50
Magnitude (dB)
Intercept Point (dBm)
60
4
3
2
1
0
50
IP2
45
IP3
40
35
30
25
0
Frequency(MHz)
200
400
600
800
1000
Frequency(MHz)
-4
-2
0
2
4
6
8
10
Output power (dBm)
Specifications and information are subject to change without notice.
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: [email protected]
Web site: www.wj.com
Page 3 of 5 April 2006
AH2
The Communications Edge TM
Product Information
High Dynamic Range Amplifier
Push-Pull, 75 : CATV Reference Design: 50 – 860 MHz
Bias Vdd = 5 V, Id = 300mA
Frequency
MHz
100
450
750
860
S21
dB
11.1
10.8
10.6
10.5
S11
dB
-10.2
-9.7
-10.8
-11
S22
dB
-13.3
-14.1
-15.4
-16.4
Output IP2
dBm
72
70
72
70
Output IP3
dBm
42
43
41
40
Noise Figure
dB
5.5
4.3
5.0
5.4
CTB
dBc
-72
CSO
dBc
-75
XMOD
dBc
-68
77 channels, 50-550MHz, +34dBmV/channel flat loading
Linearity vs. Frequency
S-Parameters
15
S21
5
0
-5
S11
-10
-15
S22
-20
-65
60
200
400
600
800
1000
XMOD
50
-70
40
30
OIP3
20
OIP2
CTB
-75
CSO
10
-80
0
0
77Channel Flat Loading, +34dBmV/Ch.
Output Power
70
dBc
Intercept Point (dBm)
10
RETURN LOSS (dB)
CTB, CSO, andXMODVs. Frequency
-60
80
0
FREQUENCY(MHz)
200
400
600
800
1000
0
100
200
300
400
500
600
Frequency(MHz)
Frequency (MHz)
Specifications and information are subject to change without notice.
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: [email protected]
Web site: www.wj.com
Page 4 of 5 April 2006
AH2
The Communications Edge TM
Product Information
High Dynamic Range Amplifier
AH2-G (Green / Lead-free SOT-89 Package) Mechanical Information
This package is lead-free/Green/RoHS-compliant. It is compatible with both lead-free (maximum 260 qC reflow temperature) and leaded
(maximum 245 qC reflow temperature) soldering processes. The plating material on the leads is NiPdAu.
Product Marking
Outline Drawing
The AH2-G will be marked with an “AH2G”
designator.
An alphanumeric lot code
(“XXXX-X” ) is also marked below the part
designator on the top surface of the package.
The obsolete tin-lead package is marked with
an “AH2” designator followed by an
alphanumeric lot code.
Tape and reel specifications for this part are
located on the website in the “Application
Notes” section.
MSL / ESD Rating
Land Pattern
ESD Rating:
Value:
Test:
Standard:
Class 1B
Passes 500V to <1000V
Human Body Model (HBM)
JEDEC Standard JESD22-A114
ESD Rating:
Value:
Test:
Standard:
Class IV
Passes 1000V to <2000V
Charged Device Model (CDM)
JEDEC Standard JESD22-C101
MSL Rating: Level 3 at +260 C convection reflow
Standard:
JEDEC Standard J-STD-020
Mounting Config. Notes
Parameter
Rating
-40 to +85 qC
59 qC / W
129 qC
Operating Case Temperature
Thermal Resistance, Rth (1)
Junction Temperature, Tj (2)
1. The thermal resistance is referenced from the hottest
part of the junction to the ground tab (pin 4).
2. This corresponds to the typical biasing condition of
+5V, 150 mA at an 85 C case temperature. A
minimum MTTF of 1 million hours is achieved for
junction temperatures below 160 C.
MTTF vs. GND Tab Temperature
1000
MTTF (million hrs)
Thermal Specifications
1. Ground / thermal vias are critical for the proper
performance of this device. Vias should use a .35mm
(#80 / .0135” ) diameter drill and have a final plated
thru diameter of .25 mm (.010” ).
2. Add as much copper as possible to inner and outer
layers near the part to ensure optimal thermal
performance.
3. Mounting screws can be added near the part to fasten
the board to a heatsink. Ensure that the ground /
thermal via region contacts the heatsink.
4. Do not put solder mask on the backside of the PC board
in the region where the board contacts the heatsink.
5. RF trace width depends upon the PC board material
and construction.
6. Use 1 oz. Copper minimum.
7. All dimensions are in millimeters (inches). Angles are
in degrees.
100
10
1
60
70
80
90
100
Tab Temperature (°C)
110
Specifications and information are subject to change without notice.
WJ Communications, Inc
Phone 1-800-WJ1-4401
FAX: 408-577-6621
e-mail: [email protected]
Web site: www.wj.com
Page 5 of 5 April 2006