PD-65 65W Dual Output Switching Power Supply series Features : Universal AC input / Full range Low leakage current<0.5mA Protections: Short circuit / Overload / Over voltage Cooling by free air convection 100% full load burn-in test Fixed switching frequency at 65KHz 2 years warranty SPECIFICATION MODEL OUTPUT PD-65B PD-65A OUTPUT NUMBER CH1 CH2 CH1 CH2 DC VOLTAGE 5V 12V 5V 24V RATED CURRENT 5.5A 2.8A 3.5A 2A CURRENT RANGE 0.4 ~ 7A 0.2 ~ 3.2A 0.4 ~ 6A 0.2 ~ 2.6A RATED POWER 61.1W OUTPUT POWER (max.) Rated output power for convection; 72W with 18CFM min. Forced air 65.5W RIPPLE & NOISE (max.) Note.2 50mVp-p 120mVp-p VOLTAGE ADJ. RANGE CH1:4.75 ~ 5.5V VOLTAGE TOLERANCE Note.3 4.0% INPUT 7.0% 150mVp-p 7.0% 1.0% 2.0% 1.0% 2.0% LOAD REGULATION 3.0% 4.0% 3.0% 4.0% SETUP, RISE TIME 800ms, 20ms at full load HOLD UP TIME (Typ.) 60ms at full load VOLTAGE RANGE 90 ~ 264VAC FREQUENCY RANGE 47 ~ 440Hz EFFICIENCY(Typ.) 78% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 1.5A/115VAC OVERLOAD PROTECTION OVER VOLTAGE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE EMC EMI CONDUCTION & RADIATION (Note 4) HARMONIC CURRENT EMS IMMUNITY MTBF DIMENSION PACKING NOTE CH1:4.75 ~ 5.5V 4.0% LINE REGULATION LEAKAGE CURRENT OTHERS 50mVp-p 127 ~370VDC 81% 0.9A/230VAC COLD START 20A/115VAC <0.75mA 40A/230VAC 73 ~ 105W rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed. CH1: 5.75 ~ 6.75VDC on CH1 Protection type : Hiccup mode, recovers automatically after fault condition is removed. -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.04%/ (0 ~ 50 ) on +5V output 10 ~ 500Hz, 2G 10min./1cycle, Period for 60min.each along X, Y, Z axes UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC Compliance to EN55022 (CISPR22) Class B Compliance to EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A 288.1K hrs min. MIL-HDBK-217F (25 127*76*42mm (L*W*H) 0.24Kg; 54pcs/15Kg/1.35CUFT ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Mounting holes M1 and M2 should be grounded for EMI purposes. File Name:PD-65-SPEC 2007-03-14 PD-65 65W Dual Output Switching Power Supply Mechanical Specification series Unit:mm 127 5.6 115.8 5.6 FG M1 M2 CN1 1 64.8 76 CN2 1 2 3 4 5 6 2 AC FUSE F4A/250V SVR1 3. 8 42 4- AC Input Connector (CN1) : Molex 5277-02 or equivalent Pin No. 1 2 Assignment AC/N AC/L Mating Housing Terminal Molex 5195 or equivalent Molex 5194 or equivalent DC Output Connector (CN2) : Molex 5273-06 or equivalent Pin No. 1 2,3 4,5 6 Assignment +V +5V COM NC Mating Housing Terminal Molex 5195 or equivalent Molex 5194 or equivalent Block Diagram fosc : 65KHz POWER SWITCHING RECTIFIERS & FILTER EMI FILTER I/P FG Derating Curve +V RECTIFIERS & FILTER +5V COM DETECTION CIRCUIT PWM CONTROL O.L.P. RECTIFIERS & FILTER O.V.P. Output Derating VS Input Voltage 100 100 90 80 80 70 LOAD(%) LOAD (%) 60 40 20 -10 0 10 20 30 40 50 AMBIENT TEMPERATURE ( ) 60 (HORIZONTAL) 60 50 40 90 100 110 135 155 230 264 INPUT VOLTAGE (V) 60Hz File Name:PD-65-SPEC 2007-03-14