Model PD6080J5050S2 Rev B Ultra Low Profile 0805 Power Divider 50Ω to 50Ω Description The PD6080J5050S2 is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package. The PD6080J5050S2 is ideal for high volume manufacturing and delivers higher performances than traditional printed and lumped element solutions. The PD6080J5050S2 is matched to 50 Ω and has a height profile of 0.5 mm which is ideal for high level integrations in the following markets: RFID, fixed satellite, and mobile satellite. The PD6080J5050S2 does not include the resistive element and therefore, requires an external resistor for operation. The PD6080J5050S2 is available on tape and reel for high volume manufacturing pick and place. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°C) Features: • • • • • • • • • • Parameter Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling Operating Temperature 6000-8000 MHz 15 dB Isolation (output ports) Good Return Loss 0.5mm Height Profile 50Ω Input / 50Ω Outputs Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Min. 6000 Typ. Max 8000 50 50 12 0.6 0.2 2 15 9 12 0.9 0.5 5 2 +85 -55 Unit MHz Ω Ω dB dB dB Degrees dB Watts ºC * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing Top View (Near-side) .079±.004 [2.00±0.10] Side View 2X .026 [0.65] .021±.002 [0.53±0.05] .039 [0.98] .049±.004 [1.25±0.10] Orientation Marker Denotes Pin Location Dimensions are in Inches [Millimeters] Mechanical Outline Bottom View (Far-side) Orientation Marker Denotes Pin Location Pin 1 2 3 4 5 6 Designation GND Input GND Output 1 GND Output 2 1 2 3 6X .009 [0.22] 6 5 6X .012 [0.30] 4 Tolerances are Non-Cumulative Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model PD6080J5050S2 Rev B Typical Broadband Performance: 500 MHz. to 9.0 GHz. Insertion Loss 0 -3 -3 -6 -6 -9 -12 -12 -15 -15 1.5 15 1 10 0.5 5 Frequency [MHz] Isolation -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 9000 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 -36 1500 Frequency [MHz] (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. 8500 8000 7500 7000 6500 6000 5500 9000 9000 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 Frequency [MHz] 0 1000 2000 9000 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 -20 3000 -2 2500 -15 2000 -1.5 1500 -10 1000 -1 1500 0 -5 500 0 -0.5 1000 deg 20 500 5000 Phase Balance 2 500 [dB] Amplitude Balance [dB] 4500 Frequency [MHz] Frequency [MHz] USA/Canada: Toll Free: Europe: 4000 3500 3000 2500 500 9000 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 -36 3000 -33 -36 2500 -30 -33 2000 -27 -30 1500 -24 -27 500 -21 -24 2000 -18 -21 1500 -18 1000 [dB] -9 1000 [dB] Return Loss - Input 0 Model PD6080J5050S2 Rev B Typical Performance: 5900 MHz. to 8100 MHz. Insertion Loss -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -15 -1.5 7900 8100 7900 8100 0.5 5 Frequency [MHz] 7300 7100 6900 6700 6500 5900 8100 -20 7900 -2 7700 -15 7500 -1.5 7300 -10 7100 -1 6300 0 -5 6100 0 -0.5 6900 7700 10 6700 7700 1 6500 7500 15 deg 1.5 6300 7300 Phase Balance 20 6100 7500 Amplitude Balance 2 5900 7100 Frequency [MHz] Frequency [MHz] [dB] 6900 6700 5900 8100 7900 7700 7500 7300 7100 -3.6 6900 -3.3 -36 6700 -3.0 -33 6500 -2.7 -30 6300 -2.4 -27 6100 -2.1 -24 6500 -1.8 -21 6300 -18 6100 [dB] 0.0 5900 [dB] Return Loss - Input 0 Frequency [MHz] Isolation 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 8100 7900 7700 7500 7300 7100 6900 6700 6500 6300 6100 -36 5900 [dB] -15 Frequency [MHz] Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model PD6080J5050S2 Rev B Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD6080J5050S2 is a Wilkinson power divider, an external 0603 100Ω resistor must be mounted in locations R1 as shown in the Figure below. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/oC. Pad Footprint w/ 0603 Resistor Location 6X .014 [0.35] 4X .012 [0.30] 6X .010 [0.25] .033 [0.85] 6X .002 [0.05] R1 Plated thru holes to ground Circuit Pattern 3X Transmission Line Footprint Pad (s) Solder Resist Dimensions are in Inches [Millimeters] Mounting Footprint USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. Model PD6080J5050S2 Rev B Packaging and Ordering Information Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. ØA ØC ØD QUANTITY/REEL 4000 TABLE 1 REEL DIMENSIONS (inches [mm]) ØA 7.00 [177.8] B 0.32 [8.0] ØC 2.0 [50.8] ØD 0.512 [13.0] B Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model PD6080J5050S2 Rev B USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing.