Model C1720J5003A00 Rev D Ultra Low Profile 0805 3 dB, 90° Hybrid Coupler Description The C1720J5003A00 is a low cost, low profile sub-miniature high performance 3 dB coupler in an easy to use surface mount package. It is designed for PCS, DCS, DECT, and WCDMA-3G applications. The C1720J5003A00 is ideal for balanced power and low noise amplifiers, plus signal distribution and other applications where low insertion loss and tight amplitude and phase balance are required. The C1720J5003A00 is available on tape and reel for pick and place high volume manufacturing. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and o Y thermal coefficient of expansion (CTE) of 17 ppm/ C. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°C) Features: • • • • • • • • • 1700 – 2000 MHz 0.7mm Height Profile PCS, DCS, DECT, & WCDMA-3G Low Insertion Loss High Isolation Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Parameter Frequency Port Impedance Return Loss Isolation Insertion Loss* Amplitude Balance Phase Balance (relative to 90°) Power Handling Min. 1700 Typ. 0.4 1.0 5 4 Unit MHz Ω dB dB dB dB Degrees Watts +85 ºC 50 27 36 0.3 0.2 1 21 24 Operating Temperature Max 2000 -55 * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing Top View (Near-side) .079±.004 [2.00±0.10] Side View 4X .026 [0.65] .028±.002 [0.700±0.05] .039 [0.98] .049±.004 [1.25±0.10] Orientation Marker Denotes Pin Location Dimensions are in Inches [Millimeters] Mechanical Outline Bottom View (Far-side) Orientation Marker Denotes Pin Location Pin 1 2 3 4 5 6 Designation Input GND Isolated Direct GND Coupled 1 2 3 6X .009 [0.22] 6 5 6X .012 [0.30] 4 Tolerances are Non-Cumulative Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model C1720J5003A00 Rev D Typical Broadband Performance: 500 MHz. to 6000 MHz. Insertion Loss -3 -0.300 -6 -0.600 -9 -0.900 -12 -1.200 -15 -1.500 Isolation 0 -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 6000 5500 5000 4500 4000 3500 -36 3000 Frequency [MHz] (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. 4500 4500 4000 3500 3000 2500 2000 Frequency [MHz] Frequency [MHz] 2500 1500 6000 -20 5500 -2 5000 -15 4500 -1.5 4000 -10 3500 -1 3000 -5 2500 -0.5 1000 0 500 0 2000 6000 5 2000 6000 0.5 1500 5500 10 1500 5500 1 1000 5000 15 1000 5000 1.5 deg 20 500 4000 Phase Balance 2 500 [dB] Amplitude Balance [dB] 3500 Frequency [MHz] Frequency [MHz] USA/Canada: Toll Free: Europe: 3000 2500 500 6000 5500 5000 4500 4000 3500 -3.600 3000 -3.300 -36 2500 -3.000 -33 2000 -2.700 -30 1500 -2.400 -27 1000 -2.100 -24 2000 -1.800 -21 1000 -18 1500 [dB] 0.000 500 [dB] Return Loss - Input 0 Model C1720J5003A00 Rev D Typical Performance: 1600 MHz. to 2100 MHz. Insertion Loss Return Loss - Input 0.0 0 -0.3 -6 -0.6 -0.9 -1.2 -15 -1.5 Frequency [MHz] Phase Balance Amplitude Balance 20 15 1 10 0.5 5 -5 1600 2100 2000 1900 -20 1800 -15 -2 1700 -10 1600 -1 -1.5 Frequency [MHz] 2100 -0.5 2000 0 1900 0 1800 deg 1.5 1700 2 [dB] 2100 1600 Frequency [MHz] 2000 -3.6 2100 -3.3 -36 2000 -3.0 -33 1900 -2.7 -30 1800 -2.4 -27 1700 -2.1 -24 1900 -1.8 -21 1800 -18 1700 [dB] -9 -12 1600 [dB] -3 Frequency [MHz] Isolation 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 2100 2000 1900 1800 1700 -36 1600 [dB] -15 Frequency [MHz] Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model C1720J5003A00 Rev D Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/oC. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. 6X .014 [0.35] 4X .012 [0.30] 6X .013 [0.33] .026 [0.66] 6X .002 [0.05] 4X Transmission Line Plated thru holes to ground Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Inches [Millimeters] Mounting Footprint USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. Model C1720J5003A00 Rev D Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. ØA ØC ØD QUANTITY/REEL 4000 TABLE 1 REEL DIMENSIONS (inches [mm]) ØA 7.00 [177.8] B 0.32 [8.0] ØC 2.0 [50.8] ØD 0.512 [13.0] B Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model C1720J5003A00 Rev D USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing.