CL25 SERIES Single, dual and triple outputs For new design -ins refer to the SCL25 series instead • • • • • • 90VAC to 264VAC Universal Input Short Circuit Protected VDE, UL, CSA and BABT Approved VDE0871 Level B Conducted Noise 25W Continuous, 35W Peak Output Power Stand alone "listed" equipment The CL25 Series of 25W (35W peak) external switching power supplies enables the system specifier to optimise the design for several reasons. Firstly, because the power supply offers pre-approved SELV outputs, the submission of the apparatus for safety approval is simplified. Secondly, the task of integrating the power supply into the mechanical design is eliminated, presenting further savings by ensuring a shorter and simpler design cycle. These advantages are complemented by Universal Input, IEC950, UL, CSA and BABT approvals, to complete a worldwide packaged power solution suitable for a wide variety of low power, desktop applications. [ 2 YEAR WARRANTY ] SPECIFICATION All specifications are typical at nominal input, full load at 25°C unless otherwise stated GENERAL SPECIFICATIONS OUTPUT SPECIFICATIONS Line regulation LL to HL, FL Single outputs Multi's: +5.1V output Multi's: aux. outputs Overshoot/undershoot At turn-on Transient response +5.1V (40% to 60% full load step) ±0.5% ±0.5% ±1.0% 110VAC 230VAC 10ms 60ms Efficiency 110VAC and 230VAC Isolation voltage Input/output Input/chassis Switching frequency Variable Approvals and standards Safety 70% typical 10% ±250mV max. dev. 1ms recovery to 1% Temperature coefficient All outputs ±0.025%/°C Overvoltage protection +5V output only 6.25V ±0.75V Output power limit Primary power limited 45W Pin max. Short circuit protection Hold-up time Continuous with auto restart 3000VAC 1500VAC 45kHz to 85kHz VDE0805, EN60950 BABT, IEC950, UL1950 CSA C22.2 No. 950 Case material ABS plastic Material flammability UL94-5V Weight Minimum output current 500g (17.65oz) 0A MTBF MIL-HDBK-217E 150,000 hours INPUT SPECIFICATIONS ENVIRONMENTAL SPECIFICATIONS Input voltage range 90 to 264VAC 120 to 370VDC Input frequency range Thermal performance Operating 0°C to +40°C Non-operating –40°C to +85°C 0°C to +40°C ambient, 25W convection cooled Peak (0°C to 40°C, max. 60s), 35W See Note 1 Relative humidity Non-condensing Altitude Operating Non-operating Vibration 5Hz to 500Hz 47 to 440Hz Input surge current 110VAC 230VAC 12A max. 24A max. Safety ground leakage current 110VAC, 60Hz 230VAC, 50Hz 1mA max. 2mA max. ELECTROMAGNETIC COMPATIBILITY SPECIFICATIONS Radiated noise EN55022, EN55011, FCC Conducted noise EN55022, EN55011, FCC Electrostatic discharge EN61000-4-2 Electrostat. air discharge IEC801-2 RF field susceptibility IEC801-3 Electrical fast EN61000-4-4 transients/bursts Surge susceptibility EN61000-4-5 Level A Level B Level 4 Level 3 Level 3 Level 3 Level 3 5% to 95% RH 10,000 feet max. 30,000 feet max. 2.4G rms (approx.) International Safety Standard Approvals geprüfte Sicherhelt VDE0805/EN60950/IEC950 File No. 10401-3336-1071 Licence No. 90353, 79517 and 1071 UL1950 File No. E136005 CSA C22.2 No. 950 File No. LR41062C/LR50913/LR101320 PAGE 1 Certificate No. 606008 AC/DC POWER SUPPLIES | 25W AC/DC 25 Watt AC/DC external power supplies OUTPUT CURRENT OUTPUT VOLTAGE MAX PEAK 5.1V 5.0A 6.0A 100mV ±4.0% CL25-7605(5) 9.5V 2.5A 3.2A 95mV ±4.0% CL25-7614 12.0V 2.0A 2.5A 120mV ±4.0% CL25-7612 16V 1.5A 2.0A 160mV ±4.0% CL25-7616 24.0V 1.0A 1.5A 240mV ±4.0% CL25-7624 48.0V 0.5A 0.7A 240mV ±4.0% CL25-7617 +5.1V (A) 2.5A 4.0A 50mV ±3.0% CL25-7618 1.0A 2.0A 120mV ±3.0% 2.5A 4.0A 50mV ±3.0% 0.8A 1.5A 150mV ±3.0% 2.5A 4.0A 50mV ±3.0% 0.5A 1.0A 240mV ±3.0% +5.1V (A) 2.0A 4.0A 50mV ±4.0% +12V (B) 1.0A 2.0A 120mV ±5.0% – 12V (C) 0.2A 1.0A 120mV ±5.0% +5.1V (A) 2.0A 4.0A 50mV ±4.0% +15V (B) 0.5A 1.5A 150mV ±5.0% –15V(C) 0.2A 1.0A 150mV ±5.0% (4) +5.1V (A) (4) +5.1V (A) (4) Notes CL25-7608(5) CL25-7610(5) SINGLE OUTPUT DUAL OUTPUT TRIPLE OUTPUT Pin 1 VA VA VA Pin 2 VA VA VA Pin 3 VA VA VA Pin 4 VA VB+ VB Pin 5 Return VB– VC Pin 6 Return Return Return Pin 7 Return Return Return Pin 8 Return Return Return 6.32 ref (160.0 +- 0.3 0.0 ) P1 7 6 A 8 ) MINI DIN PLUG 3 A 5 1 2 4 VIEW A-A SCALE: NONE 72.0 ref (1830 ± 30) J1 J 1 DS_CL25_19980401.PDF DG DL DN + 0.2 - 0.0 A MINI DIN PLUG ) "AMP" P/N 750208-4 or equiv. Mating part "AMP" P/N749232-1 or equiv. (43.0 6 CL25 -7620(5) PIN NUMBER 3.35 ref 4 5 .353 DIA (8.97) 2 3 Peak output current lasting less than 60 seconds with duty cycle <5%. During peak loading outputs may exceed total regulation limits. 50MHz bandwidth, peak-to-peak, measured differentially. Total regulation is defined as the static output regulation at 25°C, including initial tolerance, line voltage within stated limits and load currents within stated limits. Output B of dual models is a floating output. Polarity is referenced by user. The output cable length is reduced to 24” for all multiple output models and for the CL25-7605. To maintain user-system safety approvals, the input power cable must be appropriately rated and approved. A .353 DIA (8.97) 1 CL25-7619(5) 1.71 ref ±24V (B) MODEL NUMBER (3) + 0.4 - 0.2 ±15V (B) TOTAL REGULATION (2) (85.0 ±12.0V (B) RIPPLE (1) http://www.artesyn.com ALL DIMENSIONS IN INCHES (mm) PAGE 2