CL40 SERIES Single and triple output Recommended for new design-ins • • • • • • • The CL40 series is a family of 40W (50W peak) external switching power supplies. The CL40 enables the system specifier to optimise the design for several reasons. Firstly, because the power supply offers pre-approved SELV (Safety Extra Low Voltage) outputs, the submission of the apparatus for safety approval is simplified. This represents a significant saving of time and money. Secondly, the task of integrating the power supply into the mechanical design is eliminated, presenting further savings in time and money by ensuring a shorter and simpler design cycle. This means that your product gets to market faster. These advantages are complemented by universal input, CE mark, IEC950, UL, CSA, VDE and BABT approvals, to complete a worldwide packaged power solution suitable for a wide variety of low power, desktop applications. [ 2 YEAR WARRANTY ] SPECIFICATION 85VAC to 264VAC universal input range Pre-approved SELV power solution Up to 40W continuous output power Up to 50W peak output power UL, CSA, VDE and BABT approved VDE0871-A conducted noise performance Stand alone "listed" equipment All specifications are typical at nominal input, full load at 25°C unless otherwise stated ELECTROMAGNETIC COMPATIBILITY SPECIFICATIONS OUTPUT SPECIFICATIONS Line regulation LL to HL, FL Single outputs Multi's: +5.1V output Multi's: aux. outputs ±0.2% ±0.2% ±1.0% Total regulation NL to FL (Note 5) Single outputs Multi's: +5.1V output, Multi's: aux. outputs ±5.0% ±5.0% See table Overshoot/undershoot At turn-on Transient response (Single output model) +5.1V output (50% FL to 100% FL step) Radiated emissions EN55022, EN55011, FCC Conducted emissions EN55022, EN55011, FCC Electrostatic discharge EN61000-4-2 Electrostat. air discharge IEC801-2 RF field susceptibility IEC801-3 Electrical fast EN61000-4-4 transients/bursts Surge susceptibility EN61000-4-5 Level B Level A Level 4 Level 3 Level 3 Level 3 Level 3 10% max. GENERAL SPECIFICATIONS ±250mV max. dev., 1ms recovery to 1% Temperature coefficient All outputs Overvoltage protection +5.1V output only Output power limit Primary power limited Short Circuit Protection ±0.02%/°C 6.25V ±0.75V 90W Pin max. 50W Pout min. Continuous with auto-restart Hold-up time 110VAC 230VAC Efficiency 110VAC and 230VAC Isolation voltage Input/output Input/chassis Switching frequency Variable Approvals and standards 12ms 110ms 70% typical 3000VAC 1500VAC 20kHz to 70kHz VDE0805, EN60950 IEC950, IEC1010, UL1950 BABT, CSA C22.2 No. 950 INPUT SPECIFICATIONS Case material Input voltage range Note 1 ABS plastic 85 to 264VAC Material flammability Input frequency range UL94V-0 47 to 440Hz Weight Input surge current Safety ground leakage current 110VAC 230VAC 110VAC, 60Hz 230VAC, 50Hz 12A max. 30A max. 0.2mA 0.4mA MTBF 800g (28oz) MIL-HDBK-217E ENVIRONMENTAL SPECIFICATIONS Thermal performance Operating 0°C to +40°C Non-operating –40°C to +85°C 0°C to 40°C ambient 40W Peak (0°C to 40°C, max. 60s) 50W Relative humidity Non-condensing Altitude Operating Non-operating Vibration, 5Hz to 500Hz See Note 8 PAGE 1 100,000 hours min. 5% to 95% RH 10,000 feet max. 40,000 feet max. 2.4G rms (approx) AC/DC POWER SUPPLIES | 40W AC/DC 40 Watt AC/DC external power supplies OUTPUT CURRENT OUTPUT VOLTAGE (1) RIPPLE MAX (2) PEAK (4) (3) TOTAL REGULATION (5) MODEL NUMBER +5.1V (A) 3.0A 5.0A 50mV ±5.0% +12.0V (B) 1.7A 3.0A 120mV -3.0%, +7.0% –12.0V 0.35A 1.0A 120mV ±5.0% +5.1V (A) 3.0A 5.0A 50mV ±5.0% +15.0V (B) 1.3A 3.0A 150mV -2.0%, +5.0% –15.0V 0.35A 1.0A 150mV ±5.0% +5.1V 5.0A 5.0A 50mV ±6.0% CL40-7605 CL40-7605J (7) +12.0V 3.3A 4.0A 120mV ±5.0% CL40-7612 CL40-7612J (7) +13.5V 3.0A 3.7A 130mV ±5.0% CL40-7613 +15.0V 2.7A 3.3A 150mV ±5.0% CL40-7615 CL40-7615J (7) +16.5V 2.4A 3.0A 160mV ±5.0% CL40-7616 +24.0V 1.6A 2.0A 240mV ±5.0% CL40-7624 CL40-7624J (7) Notes 1 For 230VAC operation a minimum output load of 4 Watts is required. 2 Natural convection cooling, 40W maximum. 3 Peak output current lasting less than 60 seconds with duty cycle less than 10%. During peak loading outputs may go outside of regulation limits. Peak total power must not exceed 50W. 4 Figures are peak-to-peak. Output noise is measured across a 20MHz bandwidth using a 12” twisted pair terminated with a 47µF capacitor. 5 Total regulation is defined as the static output regulation at 25°C, including initial tolerance, load currents within stated limits, and output voltages adjusted to their factory settings. Also, for ‘B’ output stated regulation: I(A)/I(B)<5. 6 The standard CL40 is IEC950/VDE0805 approved as a stand-alone power supply. The plastic case incorporates an IEC 320 inlet receptacle. No input cable is supplied in Europe as standard. An input cable is supplied to customers in the US only. To order add the suffix ‘I’ to the end of the model number, e.g. CL40-7605I. In order to have a stand-alone power supply fully UL and CSA listed (as opposed to certified or recognised) it is required that the manufacturer provide an approved input cable with the power supply. 7 The standard output connector is a DIN41524 five-pin plug. As an alternative single output models can be supplied with a 2.5mm battery eliminator jack. To order this option add the suffix “J” to the model number. Example: CL40-7612J. See the table above for availability. 8 Three orthogonal axes random vibration, 10 minute test for each axis. 72 (1829) 5 CL40-7610 PIN CONNECTIONS PIN NUMBER SINGLES -7608 -7610 1 +VOUT +5.1V +5.1V 2 +VOUT +12V +15V 3 Return Return Return 4 Return –12V –15V 5 Return Return Return 2.5mm BATTERY ELIMINATOR JACK (SUFFIX 'J') - NEGATIVE 6.5 (165) + POSITIVE 3.85 (98) 1 4 CL40-7608 2 3 STANDARD OUTPUT CONNECTION (DIN 41524 FIVE PIN PLUG) International Safety Standard Approvals geprüfte Sicherhelt 2.60 (66) VDE0805/EN60950, IEC950, IEC1010 File No. 10401-3336-1062 Licence No. 1062 ALL DIMENSIONS ARE INCHES (mm) DS_CL40_19980401.PDF UL1950 File No. E136005 CSA C22.2 No. 950 File No. LR41062/LR50913/LR101320 Certificate No. PS/603191 http://www.artesyn.com PAGE 2