SL120 and SL220 SERIES Single output SL120: For new design-ins see the NFS110 Series instead SL220: For new design-ins see the NFS200 and LX200 Series instead • • • • • 115/230 VAC input UL, CSA and (VDE approved - SL120 only) Short circuit protection Floating output 20ms hold-up time min. This series of 100 Watt to 220 Watt single output switchers use an advanced circuit topology providing superior performance at low cost. Smaller and lighter than equivalent linear supplies, they are available in 5V and 24V output versions. The floating outputs can be referenced as either positive or negative. The SL120 model is UL, CSA and VDE approved. Also, selected models incorporate remote sense. SL120/220 Series power supplies are suitable for a wide variety of applications, including front end power systems, general industrial and telecom equipment. [ 2 YEAR WARRANTY ] SL120 only SPECIFICATION All specifications are typical at nominal input, full load at 25°C unless otherwise stated OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS Output voltage adjustability 5V Models 24V Models 4.5V to 5.5V 18V to 26V Line regulation LL to HL, FL ±0.2% Load regulation 60% FL, ±40% SL120 SL220 ±2.0% ±1.0% Overshoot/undershoot At turn-on Transient response SL120: +5V (12A to 20A) Temperature coefficient SL120, all outputs SL220, all outputs 5V output Output power limit SL120 SL220 ±0.03%/°C ±0.05%/°C 6.25 ±0.75V 130W min. 260W min. Short circuit protection Yes User Selectable Input frequency range 85 to 132VAC 170 to 264VAC 47Hz to 440Hz Maximum input surge current SL120: 230VAC, cold start SL220: 230VAC, cold start Safety ground leakage current 230VAC Input, 50Hz PAGE 1 22A 74A 0.7mA 36ms 36ms 20ms 20ms 65%, max. Isolation voltage SL220 SL220 SL120 SL120 Approvals and standards Safety: SL120 series Weight SL120 SL220 1.2kg (42.4oz) 2.3kg (81.2oz) MTBF SL120 SL220 25,000 hours min. 50,000 hours min. Input/Output Input/Chassis Input/Output Input/Chassis 1500VAC 1500VAC 3750VAC 1500VAC VDE0805, EN60950, UL478 CSA bulletin No. 1402C ENVIRONMENTAL SPECIFICATIONS Thermal performance Operating, See Note 8 0°C to +70°C Non-operating –40°C to +85°C Relative humidity Non-condensing Altitude Operating Non-operating INPUT SPECIFICATIONS Input voltage range Low line, full load SL120, 110VAC SL120, 230VAC SL220, 110VAC SL220, 230VAC Efficiency None ±300mV, 1ms recovery SL220: +5V (10A to 20A) ±100mV, 1ms recovery Overvoltage protection Hold-up Time 5% to 80% RH 10,000 feet max. 30,000 feet max. AC/DC POWER SUPPLIES | 100-220W AC 100 to 220 Watt AC/DC user-selectable input switch mode power supplies OUTPUT OUTPUT (1) OUTPUT REGULATION (2) (3) NOISE PK-PK MODEL NUMBER ±2.0% ±1.0% SL120-4605 ±0.2% ±1.0% ±1.0% SL220-4605 (6) ±0.2% ±1.0% ±1.0% SL220-4624 (6) LINE (4) POWER VOLTAGE ADJ. RANGE 100W 5V@20A 4.5 to 5.5V ±0.2% 220W 5V@44A 4.5 to 5.5V 220W 24V@9A 18 to 26V (5) LOAD Notes Mechanical notes 1 A Dashed line indicates minimum clearance. B Connect JP1 to either E1 (110V) or E2 (220V) as required. 2 3 4 5 6 7 8 9 Peak current in excess of the maximum indicated rating may be available on some outputs. However, this will effect output regulation. Consult factory for details. Other output voltage versions available. Consult factory for details. 20% of rated output loading is required to ensure operation within specified regulation limits. Measured from low line to high line at full load. Measured at 60% full load, ±40%. The SL220-4605 offers an auxiliary 24V output, rated at 2A on pin 7. The SL220-4624 offers an auxiliary 48V output, rated at 1A on pin 7. Output sense will compensate for up to 3VDC load line drop. The output current limit increases with output voltage. Care must be taken not to exceed the maximum output power capability of the power supply. Derate linearly from rated power at 50°C to half rated power at 70°C. This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. SL120 KULKA ELECT. 4597A-6-32-02 PIN 1 2.20 (55.88) P1 B 0.156 (3.96) DIA. 4 PLACES JP1 E1 (110V) F1 5A 250V 11.50 (292.1) E2 (230V) 11.00 (279.4) P1 SL220 P1 SL120 Pin 1 AC Live Term 1 AC Ground Pin 2 AC Ground Term 2 AC Neutral Pin 3 AC Neutral Term 3 AC Live P2 DC Output Term 1 DC Output Pin 2 DC Output Term 2 DC Output Pin 3 DC Output Term 3 DC Output Pin 4 Return Term 4 Return Pin 5 Return Term 5 Return Pin 6 Return Term 6 Return Term 7 N/C Auxiliary Output (6) 0.250 (6.35) SL220 0.67 (17.02) 3.50 (88.9) Term 8 +Remote Sense (7) Pin 9 N/C Term 9 –Remote Sense (7) (7) Pin 11 –Remote Sense (7) 110V 230V N/C +Remote Sense 4.15 (105.41 4.65 (118.11) Pin 8 Pin 10 BEAU. INC. 72-5-09C PIN 1 6-32 SCREW TYP A P2 Pin 1 Pin 7 OUTPUT VOLTAGE ADJUSTMENT PIN CONNECTIONS P2 PIN CONNECTIONS 6-32 THREADED INSERTS 4 PLACES - 2 MAX. DP. P1 P2 11.50 (292.10) 1.50 (38.10) 14.50 ± 0.02 (368.30 ± 0.06) A 14.00 (355.6) PIN 1 4.87 (123.70) 6-32 SCREW TYP 0.250 (6.35) 0.187 (4.75) DIA. 4 PLACES 3.22 (81.79) International Safety Standard Approvals: SL120-4605 only VDE0805/EN60950 File No. 10401-3336-1006, Licence No. 4345 ALL DIMENSIONS IN INCHES (mm) 1.60 2.72 (40.64) 0.87 (69.09) (22.10) UL478 Reg. File No. E131987 CSA Bulletin No. 1402C, File No. LR41062C http://www.artesyn.com PAGE 2