Issue: 01 Specification AXE10-14 Oscillator type : PXO for WLAN Test Equipment Parameter Frequency range Standard frequencies Frequency stability Initial tolerance vs. temperature in operating frequency range (steady state) vs. supply voltage variation vs. load change long term (aging) 1st year Frequency adjustment range Mechanical (internal trimmer) Electronic Frequency Control (EFC) range EFC voltage VC EFC slope (∆f / ∆VC) EFC linearity EFC input impedance Absolute pull range (APR) over 10 years, see Note 2 RF output Signal waveform Load Rise & decay time Symmetry (duty cycle) Start-up time Phase noise @ 63 MHz [100 MHz] Supply voltage VS Current consumption (steady state) Enable/disable function Operable temperature range Storage temperature range Enclosure (see drawing) Weight Packing ESD Sensitivity min. typ. max. Date: 2004-03-24 Unit Condition ±2 ±5 MHz MHz ppm ppm ppm 0°~+50°C ±0.2 ±0.1 ±1 ppm ppm ppm @ 40°C ppm ppm N.A. N.A. V N.A. 22.000 / 40.000 % kΩ ppm ppm 10 HCMOS 15 5 60 4 40 2.85 -45 -55 -95 -125 -135 -140 -145 3.0 3.15 30 +90 +105 14.4x9.5x6 max 3 Tape & reel 1500 pF ns % ms dBc dBc dBc dBc dBc V mA °C °C mm gram V @ VS/2 10 Hz 100 Hz 1 kHz 10 kHz 100 kHz @ +25°C IEC 60679-3 or 61837 IEC 60286-3 HBM as in IEC 610004-2 Notes: 1. Terminology and test conditions are according to IEC standard IEC60679-1, unless otherwise stated GmbH & Co. KG Wasemweg 5 D-74821 Lobbach Germany AXE10-14 page 1(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Enclosure drawing Pin connections Pin # Symbol 1 N.C. 2 N.C. 3 GND 4 RF OUT 5 N.C. 6 Vs Function No Connection No Connection Ground RF Output No Connection Supply Voltage Environmental conditions Test IEC 60068 Part ... Visual inspection, dimensions Sealing tests 2-17 IEC 61178-1 clause ... 4.5 4.6 4.8.2 Test conditions Enclosure styles as in IEC 60122-3, if applicable Gross leak: Test Qc, Fine leak: Test Qk Test Ta (235 ± 5)°C Method 1 Test Tb Method 1A, 5s Solderability Resistance to soldering heat Shock 2-20 4.8.3 2-27 4.8.8 Bump 2-29 4.8.6 Free fall 2-32 4.8.9 Vibration, sinusoidal 2-6 4.8.7 Rapid change of temperature 2-14 4.8.5 Dry heat 2-2 4.8.11 Damp heat, cyclic 2-30 4.8.12 Cold 2-1 4.8.13 Climatic sequence 1-7 4.8.14 Damp heat, steady state Endurance tests - ageing - extended aging 2-3 4.8.15 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Eb, 4000 bumps per Axes, 40g, 6 ms Test Ed procedure 1, 2 drops from 1m height Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Na, 10 cycles at extremes of operating temperature range Test Ba, 16 h at upper temperature indicated by climatic category Test Db variant 1 severity b), 55°C/95% r.H., 6 cycles Test Aa, 2 h at lower temperature indicated by climatic category Sequence of 4.8.11, 4.8.12 st (1 cycle), 4.8.13, 4.8.12 (5 cycles) Test Ca, 56 days 4.9.1 4.9.2 30 days @ 85°C 1000h, 2000h, 8000h @85°C GmbH & Co. KG Wasemweg 5 D-74821 Lobbach Germany AXE10-14 page 2(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]