Specification Type : Issue: 02 Date: 2005-07-15 AXLGS52F Langasite (LGS) - Crystal Resonator Unit Parameter min. typ. max. Unit Frequency range Actual frequency Crystal cut Overtone Load capacitance CL Adjustment tolerance Frequency offset Frequency stability vs. temperature in operating frequency range (steady state) long term (aging) Resonance resistance Rr Motional capacitance C1 Shunt capacitance C0 Drive level Drive level dependence (DLD) Unwanted responses Insulation resistance Operable temperature range Storage temperature range Enclosure (see drawing) Can height SMD configuration marking 5 29 Rotated Y 1 See ordering code -10 +10 -20 0 20 +50 2 15 150 7 40 100 Condition MHz MHz pF ppm ppm ppm ppm °C ppm Ω fF pF µW 30 pF if not specified @ 25°C Overall (Note 1) See chart page 2 per year @ +55°C Increasing with frequency IEC 60444-6 2·Rr 500 -40 -55 MΩ +85 °C +125 °C HC-52/U 8.8 max. on request Frequency (MHz) Spec Date Code bulk 100 V DC IEC 60122-3 (Note 5) mm Side 1 (Note 2) IEC 60286-3 Packing Notes: 1. Overall frequency stability = initial tolerance + temp. stability + aging (1st year) 2. Date Code format wwAXyy 3. Terminology and test conditions are according to IEC standard IEC60122-1, unless otherwise stated 4. Measurement technique according to IEC 60444-5 or equivalent 5. UM-1 or UM-5 package available on request Ordering Code: Model (Specification) AXLGS52F GmbH & Co. KG Wasemweg 5 D-74821 Mosbach Germany Load capacitance* Frequency [pF] [MHz] 20 10.000 *Series resonance: “S” AXLGS52F page 1(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 9 E-mail: [email protected] Enclosure drawing (in mm) Environmental conditions Test IEC 60068 Part ... Visual inspection, dimensions Sealing tests 2-17 IEC 61178-1 clause ... 4.5 4.6 4.8.2 Test conditions Enclosure styles as in IEC 60122-3, if applicable Gross leak: Test Qc, Fine leak: Test Qk Test Ta (235 ± 5)°C Method 1 Test Tb Method 1A, 5s Solderability Resistance to soldering heat Shock 2-20 4.8.3 2-27 4.8.8 Bump 2-29 4.8.6 Free fall 2-32 4.8.9 Vibration, sinusoidal 2-6 4.8.7 Rapid change of temperature 2-14 4.8.5 Dry heat 2-2 4.8.11 Damp heat, cyclic 2-30 4.8.12 Cold 2-1 4.8.13 Climatic sequence 1-7 4.8.14 Damp heat, steady state Endurance tests - ageing - extended aging 2-3 4.8.15 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Eb, 4000 bumps per Axes, 40g, 6 ms Test Ed procedure 1, 2 drops from 1m height Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Na, 10 cycles at extremes of operating temperature range Test Ba, 16 h at upper temperature indicated by climatic category Test Db variant 1 severity b), 55°C/95% r.H., 6 cycles Test Aa, 2 h at lower temperature indicated by climatic category Sequence of 4.8.11, 4.8.12 st (1 cycle), 4.8.13, 4.8.12 (5 cycles) Test Ca, 56 days 4.9.1 4.9.2 30 days @ 85°C 1000h, 2000h, 8000h @85°C GmbH & Co. KG Wasemweg 5 D-74821 Mosbach Germany AXLGS52F page 2(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 9 E-mail: [email protected]