Issue: 02 Date: 2005-05-22 Specification AXLE30S Oscillator type : TCXO with Stratum III stability incl. holdover Parameter min. Frequency range Standard frequencies Frequency stability Initial tolerance vs. temperature in operating temperature range (steady state) vs. supply voltage variation vs. load change 24 hours drift typ. max. Unit 1.5 40 1.544 /12.800 / 16.384 / 19.440 / 20.000 / 38.880 MHz MHz ± 0.5 Frequency stability ± 0.28 ± 0.28 ± 0.28 ± 0.1 ± 0.1 ± 0.04 ppm ppm ppm ppm ppm ppm ppm ppm Condition @+25°C Temperature 0°~+70°C -20°~+70°C -40°~+85°C Option I “728” “2728” “828” GR-1244-CORE or ITU G.813 24 hours holdover in operating ± 0.37 ppm temperature range and VS ± 1 % long term (aging) over 15 year ± 3.5 ppm @ +40°C Long term stability (overall)2 15 ± 4.6 ppm See Note 2 years Frequency adjustment range Electronic Frequency Control (EFC N.A. ppm N.A. RF output Signal waveform HCMOS Load 15 pF Rise & decay time 5 ns Symmetry (duty cycle) 45 55 % @ VS/2 Start-up time 10 ms @ VS – 5% 3.13 3.3 3.47 V Supply voltage VS Current consumption (steady state) 15 mA @ +25°C Pin 2 = HIGH or OPEN: Output Enable Option II = “Z” Enable/disable function (Option II) Pin 2 = LOW: Output High Z -45 +90 °C Operable temperature range -45 +90 °C Storage temperature range 25.6 x 22.7 x 7.6max. mm IEC 61837 CO 28 Enclosure (see drawing) LxWxH 9 gram Weight Tape & reel IEC 60286-3 Packing 1500 V HBM as in IEC 61000-4-2 ESD Sensitivity Notes: 1. Terminology and test conditions are according to IEC standard IEC60679-1, unless otherwise stated 2. Overall frequency stability = initial tolerance + temp.stability + supply & load change + aging Ordering Code: Model (Specification) AXLE30S GmbH & Co. KG Wasemweg 5 D-74821 Mosbach Germany Option I Option II Frequency [MHz] 728 Z 12.800 AXLE30S page 1(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Enclosure drawing Pin connections Pin # Symbol 1 N.C. 2 N.C. or E/D 3 Vs 4 RF OUT Function No Connection N.C. or Enable/Disable (Option II =”Z”) Supply Voltage RF Output 5* N.C. No Connection 6* N.C. No Connection 7 GND Ground *Note: Pins 5 & 6 may not be present Environmental conditions Test IEC 60068 Part ... Visual inspection, dimensions Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60679-1 clause ... 4.3 2-17 4.6.2 2-20 2-58 4.6.3 2-27 4.6.8 Bump* 2-29 4.6.6 Free fall* 2-32 4.6.9 Test conditions Enclosure styles as in IEC 60679-3 or 61837, if applicable Gross leak: Test Qc, Fine leak: Test Qk Test Ta (235 ± 5)°C Method 1 Test Tb Method 1A, 5s Vibration, sinusoidal* 2-6 4.6.7 Rapid change of temperature Dry heat 2-14 4.6.5 2-2 4.6.14 Damp heat, cyclic* 2-30 4.6.15 Cold 2-1 4.6.16 Climatic sequence* 1-7 4.6.17 Damp heat, steady state* Endurance tests - ageing - extended aging 2-3 4.6.18 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Eb, 4000 bumps per Axes, 40g, 6 ms Test Ed procedure 1, 2 drops from 1m height Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Na, 10 cycles at extremes of operating temperature range Test Ba, 16 h at upper temperature indicated by climatic category Test Db variant 1 severity b), 55°C/95% r.H., 6 cycles Test Aa, 2 h at lower temperature indicated by climatic category Sequence of 4.6.14, 4.6.15 (1st cycle), 4.6.16, 4.6.15 (5 cycles) Test Ca, 56 days 4.7.1 4.7.2 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C GmbH & Co. KG Wasemweg 5 D-74821 Mosbach Germany AXLE30S page 2(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]