Issue: 03 Specification AXIS60-11 Oscillator type : VCXO Parameter min. Frequency range Standard frequencies max. Supply voltage VS Current consumption (steady state) Enable/disable function Operable temperature range Storage temperature range Enclosure (see drawing) Unit MHz MHz 64,250 Frequency stability Initial tolerance vs. temperature in operating frequency range 0°~+70°C (steady state) vs. supply voltage variation vs. load change long term (aging) per year Frequency adjustment range Mechanical (internal trimmer) Electronic Frequency Control (EFC) range EFC voltage VC EFC slope (∆f / ∆VC) EFC linearity EFC input impedance RF output Signal waveform Load RL Level Harmonics attenuation Anharmonics attenuation Phase Noise L(f) Weight Packing ESD Sensitivity typ. Date: 2005-07-15 Condition Other frequencies on request -10 -20 10 20 ppm ppm ppm -3 -1 -2 3 1 2 ppm VS ± 5 % ppm RL ± 5 % ppm/year @ 40°C ppm ppm ± 100 0 5,0 V 10 % kΩ @+25°C 0°~+70°C N.A. positive 1 -2 -20 -40 4.75 SINUS 50 0 -95 -115 -125 -125 5.0 +2 5.25 45 -40 +85 -40 +85 19.1x13.1x5.5 max 3 Ω dBm dBc dBc dBc dBc dBc dBc V mA °C °C mm @ +25°C IEC 61837 CO20 modified gram Tape & reel 1500 @ 100 Hz @ 1 kHz @ 10 kHz @ 100 kHz V IEC 60286-3 HBM as in IEC 610004-2 Notes: 1. Terminology and test conditions are according to IEC standard IEC60679-1, unless otherwise stated Ordering Code: Model (Specification) AXIS60-11 GmbH & Co. KG Wasemweg 8 D-74821 Mosbach Germany Frequency [MHz] 64,250 AXIS60-11 page 1(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected] Enclosure drawing Pin connections Pin # Symbol 1 VC 2 GND 4 RF OUT 5 VS Function Control Voltage (EFC) Ground RF Output Supply Voltage Environmental conditions Test IEC 60068 Part ... Visual inspection, dimensions Sealing tests (if applicable) Solderability Resistance to soldering heat Shock* IEC 60679-1 clause ... 4.3 2-17 4.6.2 2-20 2-58 4.6.3 2-27 4.6.8 Bump* 2-29 4.6.6 Free fall* 2-32 4.6.9 Test conditions Enclosure styles as in IEC 60679-3 or 61837, if applicable Gross leak: Test Qc, Fine leak: Test Qk Test Ta (235 ± 5)°C Method 1 Test Tb Method 1A, 5s Vibration, sinusoidal* 2-6 4.6.7 Rapid change of temperature Dry heat 2-14 4.6.5 2-2 4.6.14 Damp heat, cyclic* 2-30 4.6.15 Cold 2-1 4.6.16 Climatic sequence* 1-7 4.6.17 Damp heat, steady state* Endurance tests - ageing - extended aging 2-3 4.6.18 Test Ea, 3 x per axes 100g, 6 ms half-sine pulse Test Eb, 4000 bumps per Axes, 40g, 6 ms Test Ed procedure 1, 2 drops from 1m height Test Fc, 30 min per axes, 10 Hz - 55 Hz 0,75mm; 55 Hz - 2 kHz, 10g Test Na, 10 cycles at extremes of operating temperature range Test Ba, 16 h at upper temperature indicated by climatic category Test Db variant 1 severity b), 55°C/95% r.H., 6 cycles Test Aa, 2 h at lower temperature indicated by climatic category Sequence of 4.6.14, 4.6.15 (1st cycle), 4.6.16, 4.6.15 (5 cycles) Test Ca, 56 days 4.7.1 4.7.2 30 days @ 85°C, OCXO @25°C 1000h, 2000h, 8000h @85°C GmbH & Co. KG Wasemweg 8 D-74821 Mosbach Germany AXIS60-11 page 2(2) www.axtal.com fon: +49 (6261) 939834 fax: +49 (6261) 939836 E-mail: [email protected]