® OPA OPA340 OPA2340 OPA4340 434 0 OPA 340 OPA 2340 OPA 434 0 SINGLE-SUPPLY, RAIL-TO-RAIL OPERATIONAL AMPLIFIERS MicroAmplifier ™ Series FEATURES APPLICATIONS ● ● ● ● ● ● ● ● ● DRIVING A/D CONVERTERS ● PCMCIA CARDS ● DATA ACQUISITION ● PROCESS CONTROL ● AUDIO PROCESSING ● COMMUNICATIONS ● ACTIVE FILTERS ● TEST EQUIPMENT RAIL-TO-RAIL INPUT RAIL-TO-RAIL OUTPUT (within 1mV) MicroSIZE PACKAGES WIDE BANDWIDTH: 5.5MHz HIGH SLEW RATE: 6V/µs LOW THD+NOISE: 0.0007% (f = 1kHz) LOW QUIESCENT CURRENT: 750µA/channel SINGLE, DUAL, AND QUAD of the supply rails with a 100kΩ load. They offer excellent dynamic response (BW = 5.5MHz, SR = 6V/µs), yet quiescent current is only 750µA. Dual and quad designs feature completely independent circuitry for lowest crosstalk and freedom from interaction. The single (OPA340) packages are the tiny 5-lead SOT-23-5 surface mount, SO-8 surface mount, and 8-pin DIP. The dual (OPA2340) comes in the miniature MSOP-8 surface mount, SO-8 surface mount, and 8-pin DIP packages. The quad (OPA4340) packages are the space-saving SSOP-16 surface mount, SO-14 surface mount, and the 14-pin DIP. All are specified from –40°C to +85°C and operate from –55°C to +125°C. A SPICE macromodel is available for design analysis. DESCRIPTION OPA340 series rail-to-rail CMOS operational amplifiers are optimized for low voltage, single supply operation. Rail-to-rail input/output and high speed operation make them ideal for driving sampling analog-to-digital converters. They are also well suited for general purpose and audio applications as well as providing I/V conversion at the output of D/A converters. Single, dual, and quad versions have identical specifications for design flexibility. The OPA340 series operates on a single supply as low as 2.5V with an input common-mode voltage range that extends 500mV below ground and 500mV above the positive supply. Output voltage swing is to within 1mV OPA340 OPA4340 NC 1 8 NC –In 2 7 V+ +In 3 6 V– 4 5 OPA340 Out 1 8-Pin DIP, SO-8 5 V+ V– 2 +In 3 4 –In SOT-23-5 16 Out D 15 –In D 14 +In D 4 13 –V +In B 5 12 +In C –In B 6 11 –In C Out B 7 10 Out C NC 8 9 NC Out A 1 Output –In A 2 NC +In A 3 +V A OPA2340 Out A 1 –In A 2 +In A 3 V– 4 A B 8 V+ 7 Out B 6 –In B 5 +In B 8-Pin DIP, SO-8, MSOP-8 D B C SSOP-16 International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111 • Twx: 910-952-1111 Internet: http://www.burr-brown.com/ • FAXLine: (800) 548-6133 (US/Canada Only) • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132 ® © 1997 Burr-Brown Corporation SBOS073 PDS-1404C 1 Printed in U.S.A. December, 1997 OPA340/2340/4340 SPECIFICATIONS: VS = 2.7V to 5V At TA = +25°C, RL = 10kΩ connected to VS/2 and VOUT = VS/2, unless otherwise noted. Boldface limits apply over the specified temperature range, TA = –40°C to +85°C. VS = 5V. OPA340NA, PA, UA OPA2340EA, PA, UA OPA4340EA, PA, UA PARAMETER CONDITION OFFSET VOLTAGE Input Offset Voltage vs Temperature vs Power Supply T A = –40°C to +85°C Channel Separation, dc INPUT BIAS CURRENT Input Bias Current TA = –40°C to +85°C Input Offset Current NOISE Input Voltage Noise, f = 0.1 to 50kHz Input Voltage Noise Density, f = 1kHz Current Noise Density, f = 1kHz INPUT VOLTAGE RANGE Common-Mode Voltage Range Common-Mode Rejection Ratio VOS dVOS/dT PSRR MIN VS = 5V VS = 2.7V to 5.5V, VCM = 0V VS = 2.7V to 5.5V, VCM = 0V µV µV/°C µV/V µV/V µV/V ±0.2 en in 8 25 3 VCM CMRR AOL GBW SR THD+N TA = –40°C to +85°C TEMPERATURE RANGE Specified Range Operating Range Storage Range Thermal Resistance SOT-23-5 Surface Mount MSOP-8 Surface Mount SO-8 Surface Mount 8-Pin DIP SSOP-16 Surface Mount SO-14 Surface Mount 14-Pin DIP ±500 IOS OUTPUT Voltage Output Swing from Rail(3) TA = –40°C to +85°C POWER SUPPLY Specified Voltage Range Operating Voltage Range Quiescent Current (per amplifier) TA = –40°C to +85°C ±150 ±2.5 30 ±0.2 TA = –40°C to +85°C TA = –40°C to +85°C Short-Circuit Current Capacitive Load Drive UNITS IB TA = –40°C to +85°C FREQUENCY RESPONSE Gain-Bandwidth Product Slew Rate Settling Time, 0.1% 0.01% Overload Recovery Time Total Harmonic Distortion + Noise MAX 120 120 0.2 –0.3V < VCM < (V+) –1.8V VS = 5V, –0.3V < VCM < 5.3V VS = 2.7V, –0.3V < VCM < 3V –0.3 80 70 66 INPUT IMPEDANCE Differential Common-Mode OPEN-LOOP GAIN Open-Loop Voltage Gain TA = –40°C to +85°C TYP(1) RL = 100kΩ, 5mV < VO < (V+) –5mV RL = 100kΩ, 5mV < VO < (V+) –5mV RL = 10kΩ, 50mV < VO < (V+) –50mV RL = 10kΩ, 50mV < VO < (V+) –50mV RL = 2kΩ, 200mV < VO < (V+) –200mV RL = 2kΩ, 200mV < VO < (V+) –200mV 106 106 100 100 94 94 IQ µVrms nV/√Hz fA/√Hz (V+) +0.3 V dB dB dB 1013 || 3 1013 || 6 Ω || pF Ω || pF 124 dB dB dB dB dB dB 120 114 5.5 6 1 1.6 0.2 0.0007 RL = 100kΩ, AOL ≥ 106dB RL = 100kΩ, AOL ≥ 106dB RL = 10kΩ, AOL ≥ 100dB RL = 10kΩ, AOL ≥ 100dB RL = 2kΩ, AOL ≥ 94dB RL = 2kΩ, AOL ≥ 94dB 1 10 40 MHz V/µs µs µs µs % 5 5 50 50 200 200 mV mV mV mV mV mV mA 5 950 1100 V V µA µA +85 +125 +125 °C °C °C ±50 See Typical Curve ISC CLOAD 2.7 2.5 to 5.5 750 IO = 0, VS = +5V IO = 0, VS = +5V –40 –55 –55 θJA 200 150 150 100 100 100 80 NOTES: (1) VS = +5V. (2) V OUT = 0.25V to 3.25V. (3) Output voltage swings are measured between the output and power supply rails. ® OPA340/2340/4340 2 pA pA pA 92 84 80 G=1 VS = 5V, G = 1, CL = 100pF VS = 5V, 2V Step, CL = 100pF VS = 5V, 2V Step, CL = 100pF VIN • G = VS VS = 5V, VO = 3Vp-p(2), G = 1, f = 1kHz VS ±10 ±60 ±10 °C/W °C/W °C/W °C/W °C/W °C/W °C/W ELECTROSTATIC DISCHARGE SENSITIVITY PIN CONFIGURATIONS Top View SOIC/DIP OPA4340 Out A 1 –In A 2 A 14 Out D 13 –In D This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. D +In A 3 12 +In D V+ 4 11 V– +In B 5 10 +In C –In B 6 9 –In C Out B 7 8 Out C B ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. C ABSOLUTE MAXIMUM RATINGS(1) Supply Voltage ................................................................................... 5.5V Signal Input Terminals, Voltage (2) .................... (V–) –0.5V to (V+) +0.5V Current(2) .................................................... 10mA Output Short-Circuit(3) .............................................................. Continuous Operating Temperature ................................................. –55°C to +125°C Storage Temperature ..................................................... –55°C to +125°C Junction Temperature ...................................................................... 150°C Lead Temperature (soldering, 10s) ................................................. 300°C NOTES: (1) Stresses above these ratings may cause permanent damage. (2) Input terminals are diode-clamped to the power supply rails. Input signals that can swing more than 0.5V beyond the supply rails should be currentlimited to 10mA or less. (3) Short-circuit to ground, one amplifier per package. PACKAGE/ORDERING INFORMATION PRODUCT PACKAGE PACKAGE DRAWING NUMBER(1) Single OPA340NA 5-Lead SOT-23-5 331 –40°C to +85°C A40 " " " " OPA340PA OPA340UA 8-Pin DIP SO-8 Surface-Mount 006 182 –40°C to +85°C –40°C to +85°C OPA340PA OPA340UA OPA340NA-250 OPA340NA-3K OPA340PA OPA340UA Dual OPA2340EA " OPA2340PA OPA2340UA MSOP-8 Surface-Mount " 8-Pin DIP SO-8 Surface-Mount 337 " 006 182 –40°C to +85°C " –40°C to +85°C –40°C to +85°C A40A " OPA2340PA OPA2340UA OPA2340EA-250 OPA2340EA-2500 OPA2340PA OPA2340UA Tape and Reel Tape and Reel Rails Rails (3) Quad OPA4340EA " OPA4340PA OPA4340UA SSOP-16 Surface-Mount " 14-Pin DIP SO-14 Surface Mount 322 " 010 235 –40°C to +85°C " –40°C to +85°C –40°C to +85°C OPA4340EA " OPA4340PA OPA4340UA OPA4340EA-250 OPA4340EA-2500 OPA4340PA OPA4340UA Tape and Reel Tape and Reel Rails Rails (3) " SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER(2) TRANSPORT MEDIA Tape and Reel Tape and Reel Rails Rails (3) NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with -250, -2500, and -3K are available only in Tape and Reel in the quantities indicated (e.g., -250 indicates 250 devices per reel). Ordering 3000 pieces of “OPA340NA-3K” will get a single 3000 piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book. (3) SO-8 and SO-14 models also available in Tape and Reel. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. ® 3 OPA340/2340/4340 TYPICAL PERFORMANCE CURVES At TA = +25°C, VS = +5V, and RL = 10kΩ connected to VS/2, unless otherwise noted. POWER SUPPLY and COMMON-MODE REJECTION vs FREQUENCY OPEN-LOOP GAIN/PHASE vs FREQUENCY 160 0 100 PSRR 140 80 –45 80 –90 60 40 Phase (°) 100 –135 20 PSRR, CMRR (dB) Voltage Gain (dB) 120 60 40 CMRR 20 0 –180 –20 0 0.1 10 1 100 1k 10k 100k 1M 10M 1 10 100 Frequency (Hz) 1k 10k 100k 1M Frequency (Hz) INPUT VOLTAGE AND CURRENT NOISE SPECTRAL DENSITY vs FREQUENCY CHANNEL SEPARATION vs FREQUENCY 1k 10k 140 100 10 10 1 Channel Separation (dB) 100 Voltage Noise Current Noise (fA√Hz) Voltage Noise (nV√Hz) Current Noise 1k 130 120 110 G = 1, All Channels 0.1 1 1 10 100 1k 10k 100k 100 1M 10 100 1k 100k Frequency (Hz) TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY 0.1 5k G = 100 RL = 600 4k 0.01 Output Resistance (Ω) RL = 2k THD+N (%) 10k Frequency (Hz) G = 10 RL = 10k RL = 600 0.001 RL = 2k G=1 RL = 10k 0.0001 G = 10 3k 2k G=1 1k 0 20 100 1k 10k 10 20k ® OPA340/2340/4340 100 1k 10k 100k Frequency (Hz) Frequency (Hz) 4 1M 10M TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, VS = +5V, and RL = 10kΩ connected to VS/2, unless otherwise noted. OPEN-LOOP GAIN AND POWER SUPPLY REJECTION vs TEMPERATURE 130 120 COMMON-MODE REJECTION vs TEMPERATURE 100 RL = 100kΩ AOL 90 AOL, PSRR (dB) RL = 10kΩ CMRR (dB) 80 110 RL = 2kΩ 100 PSRR 90 70 60 VS = 2.7V to 5V, VCM = –0.3V to (V+) –1.8V VS = 5V, VCM = –0.3V to 5.3V VS = 2.7V, VCM = –0.3V to 3V 50 80 40 –75 –50 –25 0 25 50 75 100 125 –75 –50 –25 Temperature (°C) 50 75 100 125 800 Per Amplifier Per Amplifier Quiescent Current (µA) 900 Quiescent Current (µA) 25 QUIESCENT CURRENT vs SUPPLY VOLTAGE QUIESCENT CURRENT vs TEMPERATURE 1000 800 700 600 500 750 700 650 600 –75 –50 –25 0 25 50 75 100 125 2.0 2.5 3.0 Temperature (°C) 4.5 5.0 5.5 6.0 60 Short-Circuit Current (mA) –ISC 80 70 60 50 4.0 SHORT-CIRCUIT CURRENT vs SUPPLY VOLTAGE SHORT-CIRCUIT CURRENT vs TEMPERATURE 90 3.5 Supply Voltage (V) 100 Short-Circuit Current (mA) 0 Temperature (°C) +ISC 40 30 20 –ISC 50 +ISC 40 10 0 30 –75 –50 –25 0 25 50 75 100 125 2.0 Temperature (°C) 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Supply Voltage (V) ® 5 OPA340/2340/4340 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, VS = +5V, and RL = 10kΩ connected to VS/2, unless otherwise noted. INPUT BIAS CURRENT vs INPUT COMMON-MODE VOLTAGE INPUT BIAS CURRENT vs TEMPERATURE 1.0 1k 0.6 100 Input Bias Current (pA) Input Bias Current (pA) 0.8 10 1 0.4 0.2 0 –0.2 –0.4 –0.6 –0.8 –1.0 0.1 –75 –50 –25 0 25 50 Temperature (°C) 75 100 125 –1 0 OUTPUT VOLTAGE SWING vs OUTPUT CURRENT +25°C –55°C Output Voltage (Vp-p) Output Voltage (V) 3 2 +125°C –55°C +25°C ±10 ±20 ±30 ±40 ±50 ±60 5 6 Maximum output voltage without slew rate-induced distortion. 4 VS = 2.7V 3 2 1M 10M Output Current (mA) Frequency (Hz) OFFSET VOLTAGE PRODUCTION DISTRIBUTION OFFSET VOLTAGE DRIFT MAGNITUDE PRODUCTION DISTRIBUTION 25 Percent of Amplifiers (%) Typical production distribution of packaged units. 12 10 8 6 4 Typical production distribution of packaged units. 20 15 10 5 2 0 0 500 400 300 200 100 0 –100 –200 –300 –400 0 –500 Percent of Amplifiers (%) 14 VS = 5.5V 0 100k ±70 ±80 ±90 ±100 18 16 4 1 0 0 3 5 4 1 2 MAXIMUM OUTPUT VOLTAGE vs FREQUENCY 6 5 +125°C 1 Common-Mode Voltage (V) 2 3 4 5 6 7 8 9 10 11 12 13 15 Offset Voltage Drift (µV/°C) Offset Voltage (µV) ® OPA340/2340/4340 1 6 TYPICAL PERFORMANCE CURVES (CONT) At TA = +25°C, VS = +5V, and RL = 10kΩ connected to VS/2, unless otherwise noted. LARGE-SIGNAL STEP RESPONSE CL = 100pF 1V/div 50mV/div SMALL-SIGNAL STEP RESPONSE CL = 100pF 1µs/div 1µs/div SETTLING TIME vs CLOSED-LOOP GAIN SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE 100 60 G = –1 0.01% Settling Time (µs) Overshoot (%) 50 G = +1 40 30 G = –5 20 10 10 0.1% 1 See text for reducing overshoot. G = +5 0.1 0 100 1000 10k 1 10 100 1000 Closed-Loop Gain (V/V) Load Capacitance (pF) ® 7 OPA340/2340/4340 APPLICATIONS INFORMATION Power supply pins should be bypassed with 0.01µF ceramic capacitors. OPA340 series op amps are fabricated on a state-of-the-art 0.6 micron CMOS process. They are unity-gain stable and suitable for a wide range of general purpose applications. Rail-to-rail input/output make them ideal for driving sampling A/D converters. In addition, excellent ac performance makes them well-suited for audio applications. The class AB output stage is capable of driving 600Ω loads connected to any point between V+ and ground. OPERATING VOLTAGE OPA340 series op amps are fully specified from +2.7V to +5V. However, supply voltage may range from +2.5V to +5.5V. Parameters are guaranteed over the specified supply range—a unique feature of the OPA340 series. In addition, many specifications apply from –40°C to +85°C. Most behavior remains virtually unchanged throughout the full operating voltage range. Parameters which vary significantly with operating voltages or temperature are shown in the typical performance curves. Rail-to-rail input and output swing significantly increases dynamic range, especially in low supply applications. Figure 1 shows the input and output waveforms for the OPA340 in unity-gain configuration. Operation is from a single +5V supply with a 10kΩ load connected to VS /2. The input is a 5Vp-p sinusoid. Output voltage is approximately 4.98Vp-p. RAIL-TO-RAIL INPUT The input common-mode voltage range of the OPA340 series extends 500mV beyond the supply rails. This is achieved with a complementary input stage—an N-channel input differential pair in parallel with a P-channel differential pair (see Figure 2). The N-channel pair is active for input voltages close to the positive rail, typically (V+) –1.3V to 500mV above the positive supply, while the P-channel pair is on for inputs from 500mV below the negative supply to approximately (V+) –1.3V. There is a small transition region, typically (V+) –1.5V to (V+) –1.1V, in which both pairs are on. This 400mV transition region can vary ±300mV with process variation. Thus, the transition region (both stages on) can range from (V+) –1.8V to (V+) –1.4V on the low end, up to (V+) –1.2V to (V+) –0.8V on the high end. VS = +5, G = +1, RL = 10kΩ 5 2V/div VIN 5 VOUT 0 FIGURE 1. Rail-to-Rail Input and Output. V+ Reference Current VIN+ VIN– VBIAS1 VBIAS2 V– (Ground) FIGURE 2. Simplified Schematic. ® OPA340/2340/4340 8 Class AB Control Circuitry VO OPA340 series op amps are laser-trimmed to the reduce offset voltage difference between the N-channel and P-channel input stages, resulting in improved commonmode rejection and a smooth transition between the N-channel pair and the P-channel pair. However, within the 400mV transition region PSRR, CMRR, offset voltage, offset drift, and THD may be degraded compared to operation outside this region. CAPACITIVE LOAD AND STABILITY OPA340 series op amps can drive a wide range of capacitive loads. However, all op amps under certain conditions may become unstable. Op amp configuration, gain, and load value are just a few of the factors to consider when determining stability. An op amp in unity gain configuration is the most susceptible to the effects of capacitive load. The capacitive load reacts with the op amp’s output resistance, along with any additional load resistance, to create a pole in the small-signal response which degrades the phase margin. In unity gain, OPA340 series op amps perform well, with a pure capacitive load up to approximately 1000pF. Increasing gain enhances the amplifier’s ability to drive more capacitance. See the typical performance curve “Small-Signal Overshoot vs Capacitive Load.” A double-folded cascode adds the signal from the two input pairs and presents a differential signal to the class AB output stage. Normally, input bias current is approximately 200fA, however, input voltages exceeding the power supplies by more than 500mV can cause excessive current to flow in or out of the input pins. Momentary voltages greater than 500mV beyond the power supply can be tolerated if the current on the input pins is limited to 10mA. This is easily accomplished with an input resistor as shown in Figure 3. Many input signals are inherently current-limited to less than 10mA, therefore, a limiting resistor is not required. One method of improving capacitive load drive in the unity gain configuration is to insert a 10Ω to 20Ω resistor in series with the output, as shown in Figure 4. This significantly reduces ringing with large capacitive loads. However, if there is a resistive load in parallel with the capacitive load, it creates a voltage divider introducing a dc error at the output and slightly reduces output swing. This error may be insignificant. For instance, with RL = 10kΩ and RS = 20Ω, there is only about a 0.2% error at the output. V+ IOVERLOAD 10mA max DRIVING A/D CONVERTERS VOUT OPAx340 VIN OPA340 series op amps are optimized for driving medium speed (up to 100kHz) sampling A/D converters. However, they also offer excellent performance for higher speed converters. The OPA340 series provides an effective means of buffering the A/D’s input capacitance and resulting charge injection while providing signal gain. 5kΩ FIGURE 3. Input Current Protection for Voltages Exceeding the Supply Voltage. Figures 5 and 6 show the OPA340 driving an ADS7816. The ADS7816 is a 12-bit, micro-power sampling converter in the tiny MSOP-8 package. When used with the miniature package options of the OPA340 series, the combination is ideal for space-limited and low power applications. For further information consult the ADS7816 data sheet. RAIL-TO-RAIL OUTPUT A class AB output stage with common-source transistors is used to achieve rail-to-rail output. For light resistive loads (>50kΩ), the output voltage is typically a few millivolts from the supply rails. With moderate resistive loads (2kΩ to 50kΩ), the output can swing to within a few tens of millivolts from the supply rails and maintain high open-loop gain. See the typical performanc curve “Output Voltage Swing vs Output Current.” With the OPA340 in a noninverting configuration, an RC network at the amplifier’s output can be used to filter high frequency noise in the signal (Figure 5). In the inverting configuration, filtering may be accomplished with a capacitor across the feedback resistor (Figure 6). V+ RS VOUT OPAx340 VIN 10Ω to 20Ω RL CL FIGURE 4. Series Resistor in Unity-Gain Configuration Improves Capacitive Load Drive. ® 9 OPA340/2340/4340 +5V 0.1µF 0.1µF 1 VREF 8 V+ 500Ω DCLOCK +In OPA340 ADS7816 12-Bit A/D 2 VIN –In CS/SHDN 3 3300pF DOUT 7 6 5 Serial Interface GND 4 VIN = 0V to 5V for 0V to 5V output. NOTE: A/D Input = 0 to VREF RC network filters high frequency noise. FIGURE 5. OPA340 in Noninverting Configuration Driving ADS7816. +5V 330pF 0.1µF 5kΩ 0.1µF 5kΩ VIN 8 V+ 1 VREF DCLOCK +In OPA340 ADS7816 12-Bit A/D 2 –In DOUT CS/SHDN 3 7 6 5 Serial Interface GND 4 VIN = 0V to –5V for 0V to 5V output. NOTE: A/D Input = 0 to VREF FIGURE 6. OPA340 in Inverting Configuration Driving ADS7816. Filters 160Hz to 2.4kHz +5V 10MΩ VIN 200pF 10MΩ 1/2 OPA2340 243kΩ 1.74MΩ 47pF 1/2 OPA2340 RL 220pF FIGURE 7. Speech Bandpass Filter. ® OPA340/2340/4340 10 PACKAGE OPTION ADDENDUM www.ti.com 6-Dec-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty OPA2340EA/250 ACTIVE MSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2340EA/250G4 ACTIVE MSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2340EA/2K5 ACTIVE MSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2340EA/2K5G4 ACTIVE MSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2340PA ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA2340PAG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA2340UA ACTIVE SOIC D 8 100 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2340UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2340UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA2340UAG4 ACTIVE SOIC D 8 100 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA340NA/250 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA340NA/250G4 ACTIVE SOT-23 DBV 5 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA340NA/3K ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA340NA/3KG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA340PA ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA340PAG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type OPA340UA ACTIVE SOIC D 8 100 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA340UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA340UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA340UAG4 ACTIVE SOIC D 8 100 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4340EA/250 ACTIVE SSOP/ QSOP DBQ 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4340EA/250G4 ACTIVE SSOP/ QSOP DBQ 16 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4340EA/2K5 ACTIVE SSOP/ QSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4340EA/2K5G4 ACTIVE SSOP/ QSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR OPA4340PA OBSOLETE PDIP N 14 Addendum-Page 1 TBD Lead/Ball Finish Call TI MSL Peak Temp (3) Call TI PACKAGE OPTION ADDENDUM www.ti.com 6-Dec-2006 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty OPA4340UA ACTIVE SOIC D 14 OPA4340UA/2K5 ACTIVE SOIC D OPA4340UA/2K5G4 ACTIVE SOIC OPA4340UAG4 ACTIVE SOIC 58 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR D 14 CU NIPDAU Level-3-260C-168 HR 58 Green (RoHS & no Sb/Br) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA MPDI001A – JANUARY 1995 – REVISED JUNE 1999 P (R-PDIP-T8) PLASTIC DUAL-IN-LINE 0.400 (10,60) 0.355 (9,02) 8 5 0.260 (6,60) 0.240 (6,10) 1 4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.020 (0,51) MIN 0.015 (0,38) Gage Plane 0.200 (5,08) MAX Seating Plane 0.010 (0,25) NOM 0.125 (3,18) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.430 (10,92) MAX 0.010 (0,25) M 4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Low Power Wireless www.ti.com/lpw Mailing Address: Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2006, Texas Instruments Incorporated