BEL S560-6600-DJ

SHDSL, HDSL2 & HDSL4 Magnetics
GlobespanVirata G2237
•
TM02394
Designed to comply with the requirements of GR1089
Power Fault, UL1950 and EN60950 supplementary
insulation with 250 VAC working voltage
•
Operating and storage temperature range: -40° to +85° C
•
Meets IEC 695, 2-2 flammability requirements
•
UL file number E169987, BABT certificate number
NC011559, CB certificate number 14210
•
PWB Process Capability: standard printed wiring board
assembly techniques, total-immersion cleaning
•
Minimum interwinding breakdown voltage of 1500 Vrms
for 1 minute between line and chip
•
Reliability testing: shock, vibration, temperature cycling,
temperature - humidity - bias
•
Minimum interwinding breakdown voltage of 600 Vrms
for 1 minute between line center tap or pin 1 and 2
•
All specifcations must be met for any DC unbalance
current up to 100mA max in the line side
ELECTRICAL SPECIFICATIONS AT 25° C
Turns
Ratio
±2%
Inductance1
mH ±6%
Leakage
Inductance2
µH max
DCR
Ω
max
IC : Line
(1-5)
(1-5)
IC
Side
1 : 5.4
3
15
0.35
Interwinding
Capacitance3
pF max
Longitudinal
Balance4
dB max
Insertion
Loss4
dB max
Return
Loss4
dB min
Harmonic
Distortion4
dB max
Line
Side
IC : Line
DC 500kHz
100kHz
40kHz 500kHz
4 Vrms
5kHz
3.8
160
-55
0.50
15
79
Part Number
S560-6600-DJ
All measurements are made with pins 2 and 4 connected except for breakdown voltage between pin 1 and 2
1. Inductance measured at 10 kHz, 0.1 Vac
2. Leakage inductance measured at 100 kHz, 0.1 Vac
3. Interwinding capacitance measured at 10 kHz, 1.0 Vac
4. Measured with line impedance of 135 Ω and chip impedance of 4.6 Ω
SCHEMATIC
S560-6600-DJ
1
9
4
IC
2
Line
7
5
©2004 Bel Fuse Inc. Specifications subject to change without notice. 01.04
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
page 1
SHDSL, HDSL2 & HDSL4 Magnetics
GlobespanVirata G2237
TM02394
MECHANICAL
1
S560-6600-DJ
Suggested PCB Pad Layout
5
0.100
[2.54]
0.741
[18.82]
0.060
[1.52]
6
10
0.087
[2.21]
0.028
[0.71]
0.100
[2.54]
0.585
[14.86]
max
0.540
[13.72]
max
0.500
[12.70]
max
0.005 [0.13]
0.606
[15.39]
0.699
[17.75]
max
10 edges
Dimensions are in inches [millimeters].
Standard dimension tolerance is ±0.005 [0.13] unless otherwise noted.
Tape and Reel Packaging
32 mm wide by 24 mm pitch; 13 inch OD, 4 inch ID
200 components per reel, maximum
Meets ANSI/EIA 481-2 Carrier Tape Standards
User Feed Direction
Orientation of Component Inside Pocket
©2004 Bel Fuse Inc. Specifications subject to change without notice. 01.04
CORPORATE
FAR EAST
EUROPE
Bel Fuse Inc.
206 Van Vorst Street
Jersey City, NJ 07302
Tel 201-432-0463
Fax 201-432-9542
www.belfuse.com
Bel Fuse Ltd.
8F / 8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel 852-2328-5515
Fax 852-2352-3706
www.belfuse.com
Bel Fuse Europe Ltd.
Preston Technology Management Centre
Marsh Lane, Suite G7, Preston
Lancashire, PR1 8UD, U.K.
Tel 44-1772-556601
Fax 44-1772-888366
www.belfuse.com
page 2