BEL S560-6600-EZ

G.SHDSL Magnetics
TM02304
•
Designed to comply with the requirements of UL1950,
BABT, CSA950, AS/N253260 and EN60950 to provide
a supplementary insulation barrier with a working
voltage of 250V
•
Minimum interwinding breakdown voltage of 1500 Vrms
•
Minimum interwinding breakdown voltage of 600 Vrms
between pin 9 and 10 for 1 minute
•
Operating and storage temperature range: -40° to +85° C
•
Meets IEC 695, 2-2 flammability requirements
•
PWB Process Capability: standard printed wiring board
assembly techniques, total-immersion cleaning
•
Reliability testing: shock, vibration, temperature cycling,
temperature - humidity - bias
ELECTRICAL SPECIFICATIONS AT 25° C
Turns Ratio
±2%
Inductance1
mH ±5%
Leakage
Inductance2
µH max
Chip : Line
Line Side
Chip Side
Chip
Side
1 : 1.8
2.75
17
4.4
Part Number
S560-6600-EZ
DCR
Ω
max
Longitudinal
Balance
dB min
Insertion
Loss
dB max
Harmonic
Distortion3
dB max
Line Side
10 kHz 400 kHz
300 kHz
13.5 dBm
@ 5 kHz
1.85
50
1.6
78
All measurements are made with pins 2 and 4 connected and pins 1 and 9 connected
1. Inductance measured at 10 kHz, 0.1 Vac
2. Measured at 100 kHz, 0.1 Vac
3. Measured with line impedance of 135 Ω and chip impedance of 41.66 Ω
SCHEMATIC
S560-6600-EZ
1
9
4
Line
IC
2
5
7
©2006 Bel Fuse Inc. Specifications subject to change without notice. 04.06
Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com
page 1
G.SHDSL Magnetics
TM02304
SUGGESTED PAD LAYOUT
5
1
0.741 [18.82]
S560-6600-EZ
(D.C.)
S560-6600 -EZ
10
0.100
[2.54]
0.087
[2.21]
MECHANICAL
0.060
[1.52]
6
0.100 [2.54]
0.028 [0.71]
0.525 [13.34]
MAX.
0.492 [12.50]
MAX.
0.520 [13.21]
MAX.
0.005 [0.13]
10 EDGES
0.606 [15.39]
0.699 [17.75]
MAX.
Dimensions are in inches [millimeters].
Standard dimension tolerance is ±0.005 [0.13] unless otherwise noted.
Tape and Reel Packaging
(D.C.)
32 mm wide by 20 mm pitch; 13 inch OD, 4 inch ID
200 components per reel, maximum
Meets ANSI/EIA 481-2-A Carrier Tape Standards
S560-6600-EZ
USER FEED DIRECTION
ORIENTATION OF COMPONENT INSIDE POCKET
©2006 Bel Fuse Inc. Specifications subject to change without notice. 04.06
CORPORATE
FAR EAST
EUROPE
Bel Fuse Inc.
206 Van Vorst Street
Jersey City, NJ 07302
Tel 201-432-0463
Fax 201-432-9542
www.belfuse.com
Bel Fuse Ltd.
8F / 8 Luk Hop Street
San Po Kong
Kowloon, Hong Kong
Tel 852-2328-5515
Fax 852-2352-3706
www.belfuse.com
Bel Fuse Europe Ltd.
Preston Technology Management Centre
Marsh Lane, Suite G7, Preston
Lancashire, PR1 8UD, U.K.
Tel 44-1772-556601
Fax 44-1772-888366
www.belfuse.com
page 2