ADSL Magnetics TM02397 • Designed to comply with the requirements of UL1950 and EN60950 to provide a supplementary insulation barrier with a working voltage of 250V • Operating and storage temperature range: -40° to +85° C • Meets IEC 695, 2-2 flammability requirements • Minimum interwinding breakdown voltage of 1500 Vrms • PWB Process Capability: standard printed wiring board assembly techniques, total-immersion cleaning • Minimum interwinding breakdown voltage of 600 Vrms between pin 9 and 10 for 1 minute • Reliability testing: shock, vibration, temperature cycling, temperature - humidity - bias ELECTRICAL SPECIFICATIONS AT 25° C Turns Ratio ±2% Inductance1 µH ±5% Leakage Inductance2 µH max Chip : Line Line Side Line Side Chip Side 1 : 1.6 440 11.5 1.8 Part Number S560-6600-FW DCR Ω max Longitudinal Balance3 dB max Insertion Loss3 dB max Frequency Response3 ±dB Harmonic Distortion3 dB max Line Side 40 kHz 500 kHz 100 kHz 40 kHz 500 kHz 12 Vpp 100 kHz 3.0 -55 0.5 0.3 -90 All measurements are made with pins 2 and 4 connected and pins 1 and 9 connected 1. Inductance measured at 10 kHz, 0.1 Vac 2. Measured at 100 kHz, 0.1 Vac 3. Measured with line impedance of 100 Ω and chip impedance of 39 Ω SCHEMATIC S560-6600-FW 1 10 4 7 2 9 5 6 Chip Line ©2002 Bel Fuse Inc. Specifications subject to change without notice. 01.02 Bel Fuse Inc. 206 Van Vorst Street, Jersey City, NJ 07302 • Tel 201-432-0463 • Fax 201-432-9542 • www.belfuse.com page 1 ADSL Magnetics TM02397 MECHANICAL 1 S560-6600-FW Suggested PCB Pad Layout 5 0.100 [2.54] 0.741 [18.82] 0.060 [1.52] 0.087 [2.21] 6 10 0.028 [0.71] 0.100 [2.54] 0.585 [14.86] max 0.540 [13.72] max 0.500 [12.70] max 0.005 [0.13] 0.606 [15.39] 0.699 [17.75] max 10 edges Dimensions are in inches [millimeters]. Standard dimension tolerance is ±0.005 [0.13] unless otherwise noted. Tape and Reel Packaging 32 mm wide by 24 mm pitch; 13 inch OD, 4 inch ID 200 components per reel, maximum Meets ANSI/EIA 481-2 Carrier Tape Standards User Feed Direction Orientation of Component Inside Pocket ©2002 Bel Fuse Inc. Specifications subject to change without notice. 01.02 CORPORATE FAR EAST EUROPE Bel Fuse Inc. 206 Van Vorst Street Jersey City, NJ 07302 Tel 201-432-0463 Fax 201-432-9542 www.belfuse.com Bel Fuse Ltd. 8F / 8 Luk Hop Street San Po Kong Kowloon, Hong Kong Tel 852-2328-5515 Fax 852-2352-3706 www.belfuse.com Bel Fuse Europe Ltd. Preston Technology Management Centre Marsh Lane, Suite G7, Preston Lancashire, PR1 8UD, U.K. Tel 44-1772-556601 Fax 44-1772-888366 www.belfuse.com page 2