Cree® SMD LED Model # LM6-PBL1-03-N1 Data Sheet 120-degree, 3.3 x 3.5-mm, SMT LED in blue color with water-transparent lens Applications • • • • Indoor and Outdoor Displays Backlighting Coupling into Light Guides RGB Full-Color Displays Absolute Maximum Ratings (TA = 25°C) Items Symbol Absolute Maximum Rating Unit R Forward Current IF 3 x 40 mA IFP 3 x 100 mA Reverse Voltage VR 5 V Power Dissipation PD 3 x 160 mW Operation Temperature Topr -40 ~ +100 °C Storage Temperature Tstg -40 ~ +100 °C Junction Temperature TJ 110 °C RTHJA 450 °C/W RTHJA 680 °C/W Junction/solder point 1 chip on RTHJS 300 °C/W Junction/solder point 3 chips on RTHJS 480 °C/W Note 1 Peak Forward Current Note 2 Junction/ambient 1 chip on Note 3 Junction/ambient 3 chips on Note 3 Notes: 1. 2. 3. Single-color light. Pulse width ≤0.1 msec, duty ≤1/10. RTH test condition: mounted on PC Board FR 4 (pad size ≥16 mm2) D-CT175.000 Data Sheet: CL Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Condition Symbol Minimum Typical Maximum Unit Dominant Wavelength IF = 3 x 20 mA λDOM 460 470 480 nm Viewing Angle at 50% IF = 3 x 20 mA 2θ½ 120 Forward Voltage IF = 3 x 20 mA VF 3.4 Luminous Intensity IF = 3 x 20 mA IV VR = 5 V IR Reverse Current (max) 355 Subject to change without notice. www.cree.com/ledlamps deg 4.0 600 V mcd 10 μA Standard Bins for LM6-PBL1-03-N1 (IF = 3 x 20 mA) Lamps are sorted to luminous intensity (IV) and chromaticity coordinates (x,y) bins shown. Orders for LM6-PBL1-03-N1 may be filled with any or all bins contained as below. All luminous intensity (IV) and chromaticity coordinates (x,y) values shown and specified are at IF = 3 x 20 mA. Luminous Intensity (IV) X3 X4 X5 X6 V2 or above 900 mcd V1 710 mcd U2 560 mcd U1 450 mcd T2 355 mcd 460 nm 465 nm 470 nm 475 nm 480 nm Dominant Wavelength (WD) Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. Tolerance of measurement of luminous intensity is ±10%. 3. Tolerance of measurement of the dominant wavelength is ±1 nm. 4. Tolerance of measurement of VF is ±0.05 V. 5. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 6. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 7. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT175.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Document No. Rev. No. Graphs Graphs 100.0 If (mA) -50 -40 -30 -20 -10 0 0.0 Vr(V) 80.0 -10.0 60.0 -20.0 40.0 -30.0 20.0 RELATIVE LUMINOUS INTENSITY 0.0 3.0 3.2 3.4 3.6 3.8 4.0 FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE. -40.0 Vf(V) -50.0 Ir(uA) FIG.2 REVERSE CURRENT VS. REVERSE VOLTAGE. Half Power WL=28nm Domi WL= 470nm 5.0 4.0 100% 3.0 75% 2.0 50% 1.0 25% If(mA) 0.0 0.0 0% 300 20.0 40.0 60.0 80.0 100.0 400 500 600 WL(nm) 700 FIG.4 RELATIVE LUMINOUS INTENSITY VS. WAVELENGTH. FIG.3 RELATIVE LUMINOUS INTENSITY VS. FORWARD CURRENT 100 SPE/LM6-PBL1-03-N1 02 IF(mA) 50% Power Angle : 120¢X Ie(%) 0 80 60 100% 80% 1 CHIP ON 60% 40 40% 20 0 20% 3 CHIP ON 0 20 40 T ( C) 60 -90 100 80 FIG.5 MAXIMUM FORWARD DC CURRENT VS SOLDER POINT TEMPERATURE 100 -30 -60 0 30 60 90 0% FIG.6 FAR FIELD PATTERN. IF(mA) 80 60 1 CHIP ON 40 20 0 3 CHIP ON 0 20 40 T ( C) 60 80 100 FIG.7 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE Items Signatures Date Prepared by WangFJ 2007-03-27 Revision History Rev.No Date Change Description Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are trademarks of Cree, Inc. 2007-03-27 Checked byregisteredXieJH DavidLiu 2007-03-27 Approved byCLD-CT175.000 02 2007-03-27 Release . Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps isplays Mechanical Dimensions Document No. Rev. No. Dimension Draw ing SPE/LM6-PBL1-03-N1 02 uides ays ngs at Ta = 25°C All dimensions are in mm. Symbol Absolute maximum Rating Unit IF 3X40 mA IFP 3X100 mA VR 5 V PD 3X160 mW Topr -40~+100 °C Tstg -40~+100 °C Tj +110 °C 3 Rth JA 450 °C/W 3 Rth JA 680 °C/W on Rth JS 300 °C/W on Rth JS 480 °C/W 3 ty <=1/10* Rth test condition: Mounted on PC Board FR 4(pad size>=16mm2) cal Characteristics(Ta = 25°C) Symbol Condition Min. Typ. Max. Unit Odom IF=3X20mA 460 470 480 nm --- 120 --- Deg. Notes 2 T½ IF=3X20mA RoHS Compliance VF IF=3X20mA -3.4 4.0 V The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the Iv IF=3 X 20mA 600 or are used--in an exempted mcd application, in accordance with EU Directhreshold limits) permitted for355 such substances, tive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment IR VR=5V through April --- 21, 2006. --10 PA (RoHS), as amended Vision Advisory Claim Users should be cautioned not to stare at the light of this LED product. The bright light can damage the eye. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. 2/4 CLD-CT175.000 Format #: COTCO-D-074 REV.4 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color 1: Full-color distribution 2~9, A~Z . . . : special request * aaaaaaaaa-aaa-aa- x x x x x IV 0: Full luminous intensity distribution 1~9, A~Z . . . : special request * Packing type 0: Standard = tape pack 1~9, A~Z . . . : special request * Product P/N * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number LM6-PBL1-03-N1-00001 Description SMD 120 Blue 470nm, FULL RANK, Tape & Reel * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT175.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps