Cree® P4 LED Model # LP377PWN1-90G Data Sheet 90-degree, 7.6 x 7.6 mm LED lamp in white color with water-transparent lens and stopper Applications • • Indicators Illuminations Absolute Maximum Ratings (TA = 25°C) Items Symbol Absolute Maximum Rating Unit IF 30 mA IFP 100 mA Reverse Voltage VR 5 V Power Dissipation PD 132 mW Operation Temperature Topr -40 ~ +95 °C Storage Temperature Tstg -40 ~ +100 °C Lead Soldering Temperature Tsol Forward Current Peak Forward Current Note Max. 260°C for 3 sec. max. (3 mm from the base of the epoxy bulb) Note: Pulse width ≤0.1 msec, duty ≤1/10. Typical Electrical & Optical Characteristics (TA = 25°C) Characteristics Symbol Condition Unit Forward Voltage VF IF = 30 mA V Reverse Current IR VR = 5 V μA Luminous Intensity IV IF = 30 mA mcd Luminous Flux ΦV IF = 30 mA mlm x IF = 30 mA 0.31 y IF = 30 mA 0.32 2θ½H-H IF = 30 mA Chromaticity Coordinates deg Typical Maximum 3.6 4.4 100 550 1100 2000 90 D-CT125.000 Data Sheet: CL 50% Power Angle Minimum Subject to change without notice. www.cree.com/ledlamps Standard Bins for LP377PWN1-90G (IF = 30 mA) Lamps are sorted to luminous intensity (IV), VF and chromaticity coordinates (x,y) bins shown. Orders for LP377PWN1-90G may be filled with any or all bins contained as below. All luminous intensity (IV), VF and chromaticity coordinates (x,y) values shown and specified are at IF = 30 mA. Luminous Intensity (IV) A1 A2 B1 B2 c U or above 1520 mcd T 1100 mcd S 770 mcd R 550 mcd Chromaticity Coordinates (x,y) Rank Chromaticity x Coordinates y A1 A2 B1 0.245 0.264 0.280 0.264 0.264 0.283 0.296 0.280 0.283 0.307 0.313 0.296 0.229 0.267 0.248 0.220 0.267 0.305 0.276 0.248 0.305 0.337 0.297 0.276 Rank B2 Chromaticity x Coordinates y c 0.307 0.330 0.330 0.313 0.330 0.361 0.356 0.330 0.337 0.360 0.318 0.297 0.360 0.385 0.351 0.318 Forward Voltage (VF) Rank Voltage V7 V8 V9 V10 V11 V12 V13 V14 2.8-3.0 V 3.0-3.2 V 3.2-3.4 V 3.4-3.6 V 3.6-3.8 V 3.8-4.0 V 4.0-4.2 V 4.2-4.4 V Important Notes: 1. All ranks will be included per delivery; rank ratio will be based on the dice distribution. 2. Pb content <1000 ppm. 3. Tolerance of measurement of luminous intensity is ±15%. 4. Tolerance of measurement of the chromaticity coordinates is ±0.01. 5. Tolerance of measurement of VF is ±0.05 V. 6. Packaging methods are available for selection; please refer to the “Cree LED Lamp Packaging Standard” document. 7. Please refer to the “Cree LED Lamp Reliability Test Standards” document for reliability test conditions. 8. Please refer to the “Cree LED Lamp Soldering & Handling” document for information about how to use this LED product safely. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT125.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps CIE Chromaticity Diagram CIE CIE Chromaticity Diagram 0.90 520 530 0.80 540 510 550 0.70 560 0.60 570 490 0.50 Y 580 590 0.40 600 c 610 620 630 B2 0.30 B1 480 A2 A1 0.20 470 0.10 460 0.00 0.00 0.10 0.20 0.30 X 4/5 0.40 0.50 0.60 0.70 Format #: COTCO-D-074 REV.4 Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT125.000 0.80 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Document No. SPE/LP377PWN1-90G Rev. No. 03 Graphs Graphs 100.0 -40 -50 Vr(V) If (mA) -30 -10 -20 0 0.0 -10.0 80.0 -20.0 60.0 -30.0 40.0 -40.0 20.0 Vf(V) 0.0 3.0 3.4 3.8 4.2 Ir(uA) 5.0 4.6 -50.0 FIG.2 REVERSE CURRENT VS. REVERSE VOLTAGE. FIG.1 FORWARD CURRENT VS. FORWARD VOLTAGE. Half Power 2.5 WL=150nm 100% 2.0 75% 1.5 50% 1.0 25% 0.5 If(mA) 0.0 0.0 20.0 40.0 60.0 0% 80.0 100.0 400 500 600 700 800 FIG.4 RELATIVE LUMINOUS INTENSITY VS. WAVELENGTH. FIG.3 RELATIVE LUMINOUS INTENSITY VS. FORWARD CURRENT IF(mA) 50 50% Power Angle : 40 90 Ie(%) 0 100% 30 80% 20 60% 10 0 40% Ta( C) 0 20 40 60 80 100 20% 120 -90 FIG.5 MAXIMUM FORWARD DC CURRENT VS AMBIENT TEMPERATURE (Tjmax=120 C) Items -60 -30 0 30 60 90 0% FIG.6 FAR FIELD PATTERN Signatures Date Prepared by LiuZM 2007-04-26 Rev. No Checked by HuangJD 2007-04-26 02 2005-10-18 Release. VF from V8~V13 to V7~V14. Approved by David 2007-04-26 03 2007-04-26 Change tolerance of CIE(x,y) from +/-0.015 to +/-0.01 FCN# Revision History Date Change Description FCN20070432 Data is subject to change without prior notice; please refer to COTCO Website for the latest version. Copyright@2002 Cotco International Ltd. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT125.000 5/5 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Format #: COTCO-D-074 REV.4 Mechanical Dimensions Document No. SPE/LP377PWN1-90G Rev. No. 03 All dimensions are in mm. Tolerance is ±0.25 mm unless otherwise noted. An epoxy meniscus may extend about 1.5 mm down the leads. Burr around bottom of epoxy max. Dimmay ensbe io0.5 n Dmm raw ing maximum Unit ting 30 mA 00 mA 5 V 32 mW ~ +95 °C ~ +100 °C 0°C forNotes 3 sec Max. e base of the epoxy bulb) RoHS Compliance cs ( The levels of environmentally sensitive, persistent biologically toxic (PBT), persistent organic pollutants (POP), or otherwise restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with EU Direcon the restriction of the use of certain hazardous substances in electrical and electronic equipment = 22002/95/EC 5 ) Tative (RoHS), as amended through April 21, 2006. °C Vision Advisory Claim Users should be Min. cautioned not to stareTyp. at the light of this LED product. The bright light can damage the eye. Condition Max. Unit F = 30mA --- 3.6 4.4 V Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. VR = 5V --- CLD-CT125.000 --- 100 PA Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps Kit Number System Cree LED lamps are tested and sorted into performance bins. A bin is specified by ranges of color, forward voltage, and brightness. Sorted LEDs are packaged for shipping in various convenient options. Please refer to the “Cree LED Lamp Packaging Standard” document for more information about shipping and packaging options. Cree LEDs are sold by order codes in combinations of bins called kits. Order codes are configured in the following manner: Standard/Custom 0: Standard C: Custom VF 0: Full forward voltage distribution 1~9, A~Z . . . : special request * Wd/Color 1: Full-color distribution 2~9, A~Z . . . : special request * aaaaaaaaa-aaa-aa- x x x x x IV 0: Full luminous intensity distribution 1~9, A~Z . . . : special request * Packing type 0: Standard = tube pack 1~9, A~Z . . . : special request * Product P/N * Contact your Cree sales representative for ordering information. Standard Available Kits* Kit Number Description LP377PWN1-90G-00001 P4 90 White, FULL RANK, Tube Pack LP377PWN1-90G-00002 P4 90 White, A1, A2, B1, B2, Tube Pack * Please contact your Cree representative about the availability of non-standard kits. Copyright © 2007 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks of Cree, Inc. CLD-CT125.000 Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5778 www.cree.com/ledlamps