CURRENT 3.0 Amperes VOLTAGE 50 to 400 Volts ES3A THRU ES3J Features · For surface applications in order optimize board space · Low profile package · Built-in strain relief, ideal for automated placement · Super fast recovery time · Plastic package has Unerwrites Laboratory Flammability Classification 94V-0 · Ideally suited for use in very high frequency switching power supplies, inverters and as free wheeling diodes · Glass passivated chip junction · High temperature soldering guaranteed: 250℃/10 seconds, at terminals DO-214AB (SMC) 0.245(6.22) 0.220(5.59) 0.124(3.15) 0.108(2.75) 0.280(7.11) 0.260(6.60) 0.012(0.31) 0.006(0.15) 0.103(2.62) 0.079(2.00) Mechanical Data · Case : JEDEC SMC(DO-214AB) molded plastic body · Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.007 ounce, 0.25 gram 0.008(0.203) MAX. 0.050(1.27) 0.030(0.76) 0.320(8.13) 0.305(7.75) Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols ES3A ES3B ES3C ES3D ES3G ES3J Units Maximum recurrent peak reverse voltage VRRM 50 100 150 200 400 600 Volts Maximum RMS voltage VRMS 35 70 105 140 280 420 Volts Maximum DC blocking voltage VDC 50 100 150 200 400 600 Volts Maximum average forward rectified current at TL=100℃ I(AV) 3.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) at TL=100℃ IFSM 100.0 Amps Maximum instantaneous forward voltage at 3.0A Maximum reverse current at rated voltage TA=25℃ TA=100℃ Maximum reverse recovery time (Note 1) Typical thermal resistance (Note 3) Typical junction capacitance (Note 2) Operating junction and storage temperature range VF IR 0.95 10.0 500 Trr RθJL RθJA CJ TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. (3) Units mounted on P.C.B 0.31×0.31"(0.8×0.8mm) copper pad areas 1.25 350 Volts μA 35 ns 12.0 47.0 ℃/W 45.0 30.0 -55 to +150 pF ℃ RATINGS AND CHARACTERISTIC CURVES ES3A THRU ES3J FIG.1-FORWARD CURRENT DERATING CURVE FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 150 RESISTIVE OR INDUCTIVE LOAD 0.31X0.31"(8.0X8.0mm) COPPER PAD AREAS PEAK FORWARD SURGE CURRENT(AMPERES) AVERAGE FORWARD CURRENT AMPERES 3.0 2.0 1.0 125 8.3ms SINGLE HALF SINE WAVE (JEDEC Method) at TL=120℃ 100 75 50 25 0 0 80 90 100 110 120 130 140 1 150 10 NUMBER OF CYCLES AT 60Hz LEAD TEMPERATURE (℃) FIG.3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS 100 1000 10 INSTANTANEOUS REVERSE CURRENT ,(mA) INSTANTANEOUS FORWARD CURRENT(AMPERES) 100 1 0.1 TJ=25℃ PULSE WIDTH=300mS 1% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 100 TJ=125℃ 10 1 TJ=75℃ TJ=25℃ 0.1 1.8 INSTANTANEOUS FORWARD VOLTAGE (VOLTS) 0.01 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) FIG.5-TYPICAL JUNCTION CAPACITANCE JUNCTIOIN CAPACITANCE(pF) 105 90 TJ=25℃ f=1.0MHz Vsig=50mVp-P 75 60 45 30 15 0 0.1 1 REVERSE VOLTAGE. VOLTS 100 100