TBL005 DC COMPONENTS CO., LTD. R THRU RECTIFIER SPECIALISTS TBL10 TECHNICAL SPECIFICATIONS OF SINGLE-PHASE SILICON BRIDGE RECTIFIER VOLTAGE RANGE - 50 to 1000 Volts CURRENT - 4.0 Amperes FEATURES * Ideal for printed circuit board * Surge overload rating: 200 Amperes peak * Molded structure TBL .768(19.5) .728(18.5) MECHANICAL DATA * * * * * .580(14.7) .540(13.7) Case: Molded plastic Epoxy: UL 94V-0 rate flame retardant Terminals: MIL-STD-202E, Method 208 guaranteed Polarity: Symbols molded or marked on body Mounting position: Any .640(16.3) .600(15.2) AC .750 (19.0) MIN. .052(1.3) .048(1.2) .083 (2.1) .220(5.6) SPACING .180(4.6) .200(5.1) .180(4.6) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) SYMBOL TBL005 TBL01 TBL02 TBL04 TBL06 TBL08 TBL10 UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS Bridge Input Voltage VRMS 35 70 140 280 420 560 700 Volts VDC 50 100 200 400 600 800 1000 Maximum DC Blocking Voltage o Maximum Average Forward Output Current at TA = 50 C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum Forward Voltage Drop per element at 3.0A DC Maximum DC Reverse Current at Rated @T A = 25 oC DC Blocking Voltage per element @T A = 100 oC 2 I t Rating for Fusing (t*8.3ms) Typical Junction Capacitance ( Note1) Typical Thermal Resistance (Note 2) Operating Temperature Range Storage Temperature Range Volts IO 4.0 Amps I FSM 200 Amps VF 1.0 Volts 10 IR 500 2 I t 93 CJ 40 Rθ J A 19 µAmps A 2 Sec pF 0 C/W TJ -55 to +150 0 C TSTG -55 to +150 0 C NOTES : 1.Measured at 1 MHZ and applied reverse voltage of 4.0 volts 2.Thermal Resistance from Junction to Ambient with units mounted on 3.0x3.0x0.11" (7.5x7.5x0.3cm )AL plate. RATING AND CHARACTERISTIC CURVES (TBL005 THRU TBL10) 300 250 8.3ms Single Half Sine-Wave (JEDEC Mathod) 200 150 100 50 0 1 2 5 10 20 50 100 FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD OUTPUT CURRENT, (A) PEAK FORWARD SURGE CURRENT, (A) FIG. 1 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 5 4 3 2 Single Phase Half Wave 60Hz Inductive or Resistive Load 1 0 50 TJ=25oC 10 Pulse Width=300ms 1% Duty Cycle 1 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, (V) 2.0 10 TJ=100oC 1.0 .1 TJ=25oC .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) DC COMPONENTS CO., LTD. R 150 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, (µA) INSTANTANEOUS FORWARD CURRENT, (A) FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 .1 100 AMBIENT TEMPERATURE, (oC) NUMBER OF CYCLES AT 60Hz