HIGH PERFORMANCE IEC CONNECTOR SERIES FILTERS KE SPECIFICATIONS INTRODUCTIONS 1. Specially designed with ground choke providing most effective EMI suppression for high frequency noise (ranged 5MHz-25MHz). 2. Bleeder resistor can be added with suffix "-R" on part numbers. 3. With optional 3300pF Y capacitor instead of 2200pF. 4. With optional 0.1uF X capacitor instead of 0.047uF. 5. With optional solder lug connection instead of fast on terminal. 6. All part numbers are UL recongnized, CSA certified and VDE approved. 1. Maximum leakage current each line-to-ground @ 115VAC 60Hz: 0.20mA @ 250VAC 50Hz: 0.40mA 2. Hipot rating (one minute) line-to-ground: 2250VDC line-to-line: 1450VDC 3. Operating frequency: 50/60Hz 4. Rated voltage: 115/250VAC COMPONENTS L (mH) Cx (uF) Cy (pF) Lg (uH) 3.1 0.8 0.047 2200 100 0.4 INSERTION LOSS (TYPICAL) 03KEEG3DA 08KEEG3DA ** UL, CSA & VDE approved to 9A 115/250VAC * VDE approved to 6A 250V MINIMUM INSERTION LOSS IN dB 30 45 50 40 DIFF. MODE COMMON MODE DIFF. MODE 10KEEG3DA 80 dB 60 dB 60 dB 40 dB 40 dB 20 dB 20 dB 0 dB 1M 100K 10K 0 dB 10M COMMON MODE 1M 100K 10K DIFF. MODE 10M ELECTRICAL SCHEMATIC L O A D L Cy G Lg 0.04 1.0 1.575 0.02 40.01 0.5 1 2 5 0.04 1.0 1.12MAX. 28.4MAX. G3D 0.85 0.004 1.575 0.005 40.01 0.13 2.18 55.5 1.79 45.5 1.18 0.02 30.0 0.5 M3 1.12 +0.02 -0 28.45 +0.5 -0 21.6 0.1 0.008 0.2 2.34 59.5 N' G' 1.95 49.5 0.13 3.3 L' R: 1M /-R ONLY 0.84MAX. MECHANICAL CONSTRUCTION Cy R Cx 21.3MAX. N L I N E 0.5 L 0.02 45 40 40 0.87 COMMON MODE (L-G) IN 50 OHM SYSTEM CURRENT FREQUENCY-MHz RATING .15 .50 1.0 5.0 10 3A 20 30 35 45 45 8A 10 15 45 40 40 10A 2 10 15 20 35 DIFFERENTIAL MODE (L-L) IN 50 OHM SYSTEM 3A 0 8 12 45 45 8A 0 5 12 40 40 10A 0 3 10 35 35 COMMON MODE 80 dB 22.2 PART NO. 03KEEG3DA/03KEEW3DA * 08KEEG3DA/08KEEW3DA **10KEEG3DA/10KEEW3DA V D E +0 R3.0 -3.0 +0 R0.12 -0.12 SUGGESTED MOUNTING CUTOUT G3D 1.95 0.04 49.5 1.0 0.04 1.0 0.85 0.004 1.575 0.005 40.01 0.13 1.12MAX. 28.4MAX. 1.87 47.5 2.02 0.04 51.5 1.0 1.18 0.02 30.0 0.5 M3 1.12 +0.02 -0 +0.5 28.45 -0 W3D 2-15 +0 R3.0 -3.0 +0 R0.12 -0.12 SUGGESTED MOUNTING CUTOUT 4.0 MIN. 100.0 MIN. W3D 21.6 0.1 2 5 0.84MAX. 1 21.3MAX. 1.575 0.02 40.01 0.5 0.87 0.02 22.2 0.5 0.13 0.008 3.3 0.2 ALL WIRE LEADS 4.0" LONG MIN. UNIT: INCH mm