Datasheet and Application Prepared by: Andreas Volke Approved by: Michael Hornkamp S/N: 010-04 Date of publication: 2003-12-05 Status: Target Data EiceDRIVER 2ED020I12-F Dual IGBT Driver IC for eupec Low and Medium Power IGBT Modules eupec GmbH Max-Planck-Straße 5 D-59581 Warstein Tel. +49 (0) 29 02 7 64-0 Fax + 49 (0) 29 02 7 64-12 56 [email protected] www.eupec.com www.eicedriver.com Author: Andreas Volke Datasheet and Application EiceDRIVER™ 2ED020I12-F 0 History Revision 1.0 Revision 1.2 Revision 1.5 2003-01-24 2003-05-16 2003-12-05 First release Updated electrical characteristics New paper design Updated functional description Updated electrical characteristics New chapter “Diagrams” New chapter “Applications” For questions on technology, delivery and prices please contact the eupec offices in Germany or the eupec companies and representatives worldwide: See our web pages at http://www.eupec.com and http://www.eicedriver.com Published by eupec GmbH, Max-Planck-Str. 5, D-59581 Warstein © eupec GmbH 2003. All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as warranted characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. eupec GmbH is an approved CECC manufacturer. Information For further information on technology, delivery terms, conditions and prices please contact your nearest eupec office in Germany or our eupec representatives worldwide. Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest eupec office. eupec components may only be used in life-support devices or systems with the express written approval of eupec, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. Exclusion Clause The eupec IGBT driver 2ED020I12-F is only intended for control of eupec IGBT modules. The company eupec GmbH cannot warrant against damage and/or dysfunction if IGBT modules used not produced by eupec. www.eupec.com - www.eicedriver.com Page 2/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F Table of Contents 0 History.................................................................................................................................................................................2 1 Overview.............................................................................................................................................................................4 1.1 Coreless transformer (CLT) technology....................................................................................................................4 2 Pin configuration and package outline ................................................................................................................................6 3 Block diagram .....................................................................................................................................................................7 4 Functional description .........................................................................................................................................................8 4.1 Power supply ............................................................................................................................................................8 4.2 Logic inputs ..............................................................................................................................................................8 4.2.1 5 Gate driver ...........................................................................................................................................................8 4.3 General purpose operational amplifier......................................................................................................................8 4.4 General purpose comparator....................................................................................................................................8 4.5 CLT...........................................................................................................................................................................8 Electrical parameters ..........................................................................................................................................................9 5.1 Absolute maximum ratings .......................................................................................................................................9 5.2 Operating range......................................................................................................................................................10 5.3 Electrical characteristics .........................................................................................................................................10 5.3.1 Voltage Supply...................................................................................................................................................10 5.3.2 Logic inputs .......................................................................................................................................................11 5.3.3 Gate drivers .......................................................................................................................................................11 5.3.4 Dynamic characteristics .....................................................................................................................................11 5.3.5 General purpose operational amplifier...............................................................................................................12 5.3.6 General purpose comparator .............................................................................................................................12 6 Diagrams ..........................................................................................................................................................................13 7 Application Notes..............................................................................................................................................................15 7.1 Power Supply .........................................................................................................................................................15 7.2 Ground reference ...................................................................................................................................................15 7.3 Operational Amplifier ..............................................................................................................................................16 7.4 Comparator ............................................................................................................................................................17 7.5 Logic inputs ............................................................................................................................................................18 www.eupec.com - www.eicedriver.com Page 3/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 1 Overview The 2ED020I12-F is a high voltage, high speed power IGBT and MOSFET driver of the eupec EiceDRIVER™ family with interlocking high and low side referenced output channels. The floating high side driver may be supplied directly or by means of a bootstrap diode and capacitor. In addition to the logic input of each driver the 2ED020I12-F is equipped with a dedicated shutdown input. All logic inputs are compatible with 3.3 V and 5 V TTL. The output drivers feature a high pulse current buffer stage designed for minimum driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. Both drivers are designed to drive an n-channel power IGBT or MOSFET which operates up to 1200 V. In addition, a general purpose operational amplifier and a general purpose comparator are provided, which may be used e.g. for current measurement or over current detection. Product Highlights • Fully operational to ±1200 V • Gate drive supply range from 13 to 18 V • Gate drive currents of +1 A / –2 A • Matched propagation delay for both channels • High dV/dt immunity • General purpose operational amplifier • General purpose comparator Features • Floating high side driver • Under-voltage lockout for both channels • 3.3 V and 5 V TTL compatible inputs • CMOS Schmitt-triggered inputs with internal pull-down • CMOS Schmitt-triggered shutdown with internal pull-up • Non-inverting inputs • Interlocking inputs • Dedicated shutdown input with internal pull-up • IEC compliant (pending) • UL recognized (pending) 1.1 Coreless transformer (CLT) technology In various IGBT and power MOSFET driver stages are optocoupler, level shifter or discrete transformer included to overcome the isolation barrier between the low side input and high side output. All of them have their typical advantages and disadvantages. As an alternative for low and medium power applications the coreless transformer technology combines almost all advantages and at the same time avoiding almost all disadvantages of these devices by a very cost efficient way and high voltage isolation capability. The principle function of the CLT is realized by two coils which are compounded on silicon within one integrated circuit. The isolation between these coils can withstand in the current design at least up to 1200 V whereby a functional isolation is achieved. Figure 1 shows a schematic of the internal stages of the IC. Figure 1 IC schematic www.eupec.com - www.eicedriver.com Page 4/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F Each EiceDRIVER™ has a type number, which can be resolved by the following schemata: EiceDRIVER™ 2 ED 020 I 12 - F Isolation class F = Function isolation S = Safety isolation ST = Safety isolation / Traction application Voltage class: 06 = 600 V 12 = 1200 V 17 = 1700 V 33 = 3300 V 65 = 6500 V Type: C = Board I = IC (Coreless Transformer) L = IC (Level Shifter) Peak output current for Driver: 020 = 2 A 300 = 30 A Maximum Sampling Rate for ADC/DC Function: EC = Analog-Digital-Converter/Digital-Coupler ED = IGBT/MOSFET Driver Driver Channels: 1 = Driver for one IGBT 2 = Driver for Half-Bridge 6 = Driver for Six-Pack ADC/DC Channels: 1 = Single Input/Single Output www.eupec.com - www.eicedriver.com Page 5/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 2 Pin configuration and package outline P-DSO-18-1 (300 mil) 1) 2) Figure 2 Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Pin configuration (top view) Symbol InH InL /SD GND /CPO CPCP+ OPO OPOP+ GNDL OutL VS n.c. n.e. n.e. GNDH VSLH OutH GNDH Does not include plastic or metal protrusions of 0.15 max per side Does not include dambar protrusion of 0.05 max per side Figure 3 Package outline (all measures in mm) Function Logic input for high side driver Logic input for low side driver Logic input for shutdown of both drivers Common ground Open drain output of general purpose comparator Inverting input of general purpose comparator Non-inverting input of general purpose comparator Output of general purpose operational amplifier Inverting input of general purpose operational amplifier Non-inverting input of general purpose operational amplifier Low side supply ground Low side gate driver output Low side supply voltage (not connected) (not existing) (not existing) High side supply ground High side supply voltage High side gate driver output High side supply ground www.eupec.com - www.eicedriver.com Page 6/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 3 Block diagram Figure 4 Block diagram www.eupec.com - www.eicedriver.com Page 7/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 4 4.1 Functional description Power supply The power supply of both sides, VSL and VSH, is monitored by an under-voltage lockout block (UVLO) which enables operation of the corresponding side when the supply voltage reaches the “on” threshold of 12 V. Afterwards the internal voltage reference and the biasing circuit are enabled. When the supply voltage (VSL, VSH) drops below the “off” threshold of 11 V the circuit is disabled. 4.2 Logic inputs The logic inputs InH, InL and /SD are fed into Schmitt-Triggers with thresholds compatible to 3.3 V and 5 V TTL. When /SD is enabled (low), InH and InL are disabled. If InH is high (while InL is low), OutH is enabled and vice versa. However, if both signals are high, they are internally disabled until both signals get low again. This is due to the interlocking logic of the device (see also Figure 5). 4.3 Gate driver 2ED020I12-F features two hard-switching gate drivers with n-channel output stages capable to source 1 A and to sink 2 A peak current. Both drivers are equipped with active-low-clamping capability. Furthermore, they feature a large ground bounce ruggedness in order to compensate ground bounces caused by a turn-off of the driven IGBT. 4.4 General purpose operational amplifier This general purpose operational amplifier can be applied for current measurement of the driven low-side IGBT. It is dedicated for fast operation with a gain of at least 10. The OP is equipped with a -0.1 V to 2 V input stage and a rail-to-rail output stage which is capable to drive ±5 mA and is dedicated to drive an A/D converter. 4.5 General purpose comparator The general purpose comparator can be applied for over-current detection of the low side IGBT. A dedicated offset as well as a pull-up and pull-down resistor has been introduced to its inputs for security reasons. 4.6 CLT In order to enable signal transmission across the isolation barrier between low-side and high-side driver, a coreless transformer is employed. Signals, that are to be transmitted, are specially encoded by the transmitter and correspondingly restored by the receiver. In this way EMI due to variations of GNDH (dVGNDH/dt) or the magnetic flux (dΦ/dt) can be suppressed. To compensate the additional propagation delay of transmitter, coreless transformer and receiver, a dedicated propagation delay is introduced into the low-side driver. www.eupec.com - www.eicedriver.com Page 8/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 5 5.1 Electrical parameters Absolute maximum ratings Absolute maximum ratings are defined as ratings, which when being exceeded may lead to destruction of the integrated circuit. Unless otherwise noted all parameters refer to GND. The pins GND and GNDL have to be connected externally through the shortest possible way. Parameter High side ground High side supply voltage High side gate driver output Low side ground Low side supply voltage Low side gate driver output Logic input voltages (InH, InL, /SD) OP input voltages (OP-, OP+) OP output voltage CP input voltages (CP-, CP+) CP output voltage CP output max. sink current High side ground, voltage transient Package power dissipation @TA=25°C Thermal resistance (both chips active), junction to ambient Thermal resistance (high side chip), junction to ambient Thermal resistance (low side chip), junction to ambient Junction temperature Storage temperature VGNDH VVSH VOutH VGNDL VVSL VOutL VIn Limit values min. -1200 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 max. 1200 20 VVSH + 0.3 5.3 20 VVSL + 0.3 5.3 V V V V V V V VOP -0.3 5.3 V VOPO VCP -0.3 -0.3 5.3 5.3 V V V/CPO I/CPO dVGNDH/dt -0.3 -50 5.3 5 50 V mA V/ns PD 2 W 5) RTHJA 60 K/W 6) RTHJA(HS) 110 K/W 6) RTHJA(LS) 110 K/W 6) TJ TS -55 150 150 °C °C Symbol Unit Remark 1) 1) 2) 3) 4) 4) 1) with reference to high side GNDH with reference to both GND and GNDL 3) with reference to low side ground GNDL 4) please note the different specifications for the operating range 5) considering RTHJA = 60 K/W, e.g. both chips active 6) device soldered to reference PCB without cooling area 2) www.eupec.com - www.eicedriver.com Page 9/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 5.2 Operating range Within the operating range the IC operates as described in the functional description. Unless otherwise noted all parameters refer to GND. Parameter High side ground High side supply voltage Low side supply voltage Logic input voltages (InH, InL, /SD) OP input voltages (OP-, OP+) CP input voltages (CP-, CP+) Ambient temperature Symbol Unit VGNDH VVSH VVSL VIn Limit values min. -1200 13 13 0 max. 1200 18 18 5 V V V V VOP -0.1 2 V VCP -0.1 2 V TA -40 105 °C Remark 1) 2) 1) with reference to high side ground GNDH 2) with reference to both GND and GNDL 5.3 Electrical characteristics The electrical characteristics involve the spread of values for the supply voltages, load and junction temperature given below. Typical values represent the median values, which are related to production processes. Unless otherwise noted all voltages are given with respect to ground (GND). 1) VSL = 15 V, VSH = 15 V , CL = 1 nF, TA = 25°C. Positive currents are assumed to be flowing into pins. 5.3.1 Voltage Supply Parameter 1) Symbol Limit Values min. typ. Unit Test condition max. 1 µA 1.7 12 500 tbd mA µA V VGNDH = 1.2 kV VGNDL = 0 V 1) VVSH = 15 V 1) VVSH = 10 V High side leakage current IGNDH High side quiescent supply current IVSH High side under-voltage lockout, upper threshold High side under-voltage lockout hysteresis Low side quiescent supply current VVSH1) tbd ∆VVSH tbd 1 tbd V IVSL Low side under-voltage lockout, upper threshold Low side under-voltage lockout hysteresis VVSL tbd 2.4 12 500 tbd mA µA V ∆VVSL tbd 1 tbd V VVSL = 15 V VVSL = 10 V with reference to high side ground GNDH www.eupec.com - www.eicedriver.com Page 10/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 5.3.2 Logic inputs Parameter Logic “1” input voltages (InH, InL, /SD) Logic “0” input voltages (InH, InL, /SD) Logic input voltages hystersis (InH, InL, /SD) Logic “1” input current (InH, InL) Logic “0” input current (InH, InL) Logic “1” input current (/SD) Logic “0” input current (/SD) 5.3.3 VIn Limit Values min. typ. 2 max. V VIn 0.8 V ∆VIn 0.6 V IIn 40 tbd µA VIn = 5 V IIn 0 µA VIn = 0 V IIn 0 µA VIn = 5 V IIn tbd -40 µA VIn = 0 V Symbol Test condition Gate drivers High side high level output voltage VVSH – VOutH Limit Values min. typ. 1.4 High side low level output voltage VOutH1) 0.1 V Low side high level output voltage VVSL – VOutL 1.4 tbd V Low side low level output voltage VOutL 0.1 V Output high peak current (OutL, OutH) Output low peak current (OutL, OutH) High side active low clamping IOut -1 A IOut 2 A VOutH1) 3 V Low side active low clamping VOutL 3 V Parameter 1) Unit Symbol Unit Test condition max. tbd V IOutH = -1 mA VInH = 5 V IOutH = 1 mA VInH = 0 V IOutH = -1 mA VInH = 0 V IOutH = 1 mA VInH = 0 V VIn = 5 V VOut = 0 V VIn = 0 V VOut = 15 V VInH = 0V VSH open IOutH = 200 mA VInL = 0V VSL open IOutL = 200 mA with reference to high side ground GNDH 5.3.4 Dynamic characteristics Parameter Turn-on propagation delay Turn-off propagation delay Shutdown propagation delay Turn-on rise time Turn-off rise time Delay mismatch (high and low side turn-on/off) Symbol ton toff t/SD tr tf ∆t Limit Values min. typ. 50 50 50 40 40 -10 0 www.eupec.com - www.eicedriver.com max. tbd tbd tbd tbd tbd 10 Unit Test condition ns ns ns ns ns ns ref. to Figure 6 ref. to Figure 6 ref. to Figure 7 ref. to Figure 6 ref. to Figure 6 ref. to Figure 8 Page 11/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 5.3.5 General purpose operational amplifier OP input offset voltage OP input offset voltage drift OP input high currents (OP-, OP+) OP input high currents (OP-, OP+) OP high output voltage ∆VIn VDrift IIn Limit Values min. typ. -15 0 tbd tbd 0 IIn -5 0 µA VIn = 0 V VOPO 4.9 V OP low output voltage VOPO 0.1 V OP output source current IOPO -5 mA OP output sink current IOPO 5 mA VOP- = 0 V VOP+ = 2 V VOP- = 2 V VOP+ = 0 V VOP+ = 2 V VOP- = 0 V VOPO = 0V VOP+ = 0 V VOP- = 2 V VOPO = 5V OP open loop gain OP gain-bandwidth product OP phase margin AOL A x BW Φ 120 60 70 dB MHz ° Symbol Unit Test condition max. 0.2 mV µA µA V VCP+ = VCPVCP- = 5 V VCP+ = 0 V VCP+ = 2 V I/CPO = 1 mA VCP+ = 0 V VCP- = 2 V V/CPO = 5 V R/CPO = 4.7 kΩ Vres = 5 V V/CPO = 0.8 V R/CPO = 4.7 kΩ Vres = 5 V V/CPO = 2 V Parameter 1) 2) Symbol Unit Test condition max. 15 tbd 5 mV µV/K µA VIn = 2 V 1) 1), 2) design value the minimum gain A ≥ 10 is recommended 5.3.6 General purpose comparator CP input offset voltage CP input high current CP input low current CP low output voltage ∆VIn ICPICP+ V/CPO Limit Values min. typ. -30 20 -20 CP output leakage current I/CPO 5 µA CP switch-on delay td 100 ns CP switch-off delay td 300 ns Parameter www.eupec.com - www.eicedriver.com Page 12/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 6 Diagrams InH InL /SD OutH OutL Figure 5 Input/Output timing diagram Figure 6 Switching time waveform definition Figure 8 Delay matching waveform definitions Figure 7 www.eupec.com - www.eicedriver.com Shutdown waveform definition Page 13/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F Junction Temperature [°C] FS75R12KM4 (Rg = 2.4 Ω, VDC-Link = 100 V) Frequency [kHz] Figure 9 Junction Temperature vs. Frequency (VVSH = VVSL = 15 V, TA = 25°C) www.eupec.com - www.eicedriver.com Page 14/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 7 7.1 Application Notes Power Supply The floating high side driver may be supplied directly or by means of a bootstrap diode and capacitor. Either way, for a correct power-up it is recommended to put at the pins VSH and VSL an electrolytic or tantalum capacitor and additionally a ceramic capacitor of approximately 100 nF. The size of the electrolytic or tantalum capacitor depends on the gate capacitances of the driven IGBT or MOSFET, the switching frequency and additional gate resistors and/or capacitors. For a safe start-up with a bootstrap diode and capacitor it is recommended first to switch on the low-side IGBT. Thus, the capacitor can be charged through the diode and provides sufficient gate voltage. Figure 10 7.2 Bootstrap circuit Ground reference The pins GND and GNDL have to be connected externally through the shortest possible way. Thus, different ground references result for different applications as shown for instance in Figure 11. Figure 11 Ground reference www.eupec.com - www.eicedriver.com Page 15/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 7.3 Operational Amplifier To minimize the current consumption when the operational amplifier is not used, it is necessary to connect both inputs properly. For instance connect pin OP+ to 5 V and pin OP- to 0 V or vice versa. Figure 12 OPA not used The operational amplifier is designed to operate with a minimum gain of 10, so that its output OPO has a stable behavior. Figure 13 Minimum OPA gain www.eupec.com - www.eicedriver.com Page 16/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 7.4 Comparator The comparator has a designed input offset voltage of typical -30 mV to prioritize the CP+ input against the CP- input. If both input signals have the same potential, the output /CPO goes to low impedance. In the following some example circuits using the general purpose comparator: Figure 14 Over-current detection Figure 15 Figure 16 Over-current detection with Window Comparator www.eupec.com - www.eicedriver.com Comparator with hysteresis Page 17/18 Datasheet and Application EiceDRIVER™ 2ED020I12-F 7.5 Logic inputs The input pins InH, InL and /SD should be protected against EMI by ceramic capacitors according to Figure 17. Figure 17 Logic inputs eupec Headquarter eupec GmbH Max-Planck-Strasse 5 D-59581 Warstein Phone +49 2902 764-0 Fax +49 2902 1256 [email protected] www.eupec.com - www.eicedriver.com Page 18/18