NB6L16 2.5V / 3.3V Multilevel Input to Differential LVPECL/LVNECL Clock or Data Receiver/Driver/Translator Buffer The NB6L16 is a high precision, low power ECL differential clock or data receiver/driver/translator buffer. The device is functionally equivalent to the EL16, EP16, LVEL16 and NBSG16 devices. With output transition times of 70 ps, it is ideally suited for high frequency, low power systems. The device is targeted for Backplane buffering, GbE clock/data distribution, Fibre Channel distribution and SONET clock/data distribution applications. Input accept LVNECL (Negative ECL), LVPECL (Positive ECL), LVTTL, LVCMOS, CML, or LVDS. Outputs are 800 mV ECL signals. The VBB pin, an internally generated voltage supply, is available to this device only. For single−ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 mF capacitor and limit current sourcing or sinking to 0.5 mA. When not used, VBB should be left open. • Maximum Input Clock Frequency 6 GHz Typical • Maximum Input Data Rate Frequency 6 Gb/s Typical • Low 12 mA Typical Power Supply Current • 70 ps Typical Rise/Fall Times • 130 ps Input Propagation Delay • On−Chip Reference for ECL Single−Ended Input − VBB Output • PECL Mode Operating Range: VCC = 2.375 V to 3.465 V with VEE = 0 V • NECL Mode Operating Range: VCC = 0 V with VEE = −2.375 V to −3.465 V • Open Input Default State • LVDS, LVPECL, LVNECL, LVCMOS, LVTTL and CML Input Compatible • Pb−Free Packages are Available Semiconductor Components Industries, LLC, 2004 September, 2004 − Rev. 4 1 http://onsemi.com MARKING DIAGRAMS* 8 8 6L16 ALYW 1 SOIC−8 D SUFFIX CASE 751 8 1 8 1 TSSOP−8 DT SUFFIX CASE 948R A L Y W 6L16 ALYW 1 = Assembly Location = Wafer Lot = Year = Work Week *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. Publication Order Number: NB6L16/D NB6L16 NC 1 D 2 8 VCC 7 Q 6 Q 5 VEE R2 R1 D R1 3 R2 VBB 4 Figure 1. Pinout (Top View) and Logic Diagram Table 1. PIN DESCRIPTION Pin Name I/O Default State Description 1 NC − − 2 D LVDS, CML, LVPECL, LVNECL, LVTTL, LVCMOS Input LOW Non−inverted differential clock/data input. Internal 75 k to VCC and 37.5 k to VEE. 3 D LVDS, CML, LVPECL, LVNECL, LVTTL, LVCMOS Input HIGH Inverted differential clock/data input. Internal 37.5 k to VCC and 75 k to VEE. 4 VBB − − Internally generated ECL reference voltage supply. 5 VEE − − Negative power supply voltage. 6 Q ECL Output Inverted differential ECL output. Typically terminated with 50 resistor to VCC – 2.0 V. 7 Q ECL Output Non−inverted differential ECL output. Typically terminated with 50 resistor to VCC – 2.0 V. 8 VCC − No Connect. The NC pin is electrically connected to the die and MUST be left open. − Positive power supply voltage. Table 2. ATTRIBUTES Characteristics Value Internal Input Default State Resistor (R1) 37.5 k Internal Input Default State Resistor (R2) 75 k ESD Protection Human Body Model Machine Model Charged Device Model Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) Flammability Rating Oxygen Index: 28 to 34 Transistor Count > 2 kV > 100 V > 1 kV Level 1 UL 94 V−0 @ 1.125 in 167 Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. http://onsemi.com 2 NB6L16 Table 3. MAXIMUM RATINGS Symbol Parameter Condition 1 Condition 2 Rating Unit s VCC PECL Mode Power Supply VEE = 0 V 3.6 V VEE NECL Mode Power Supply VCC = 0 V −3.6 V VI PECL C Mode ode Input u Voltage o age NECL Mode Input Voltage VEE = 0 V VCC = 0 V 3.6 3 6 −3.6 V V Iout Output Current Continuous Surge 25 50 mA mA VINPP Differential Input Voltage 2.8 |VCC − VEE| V IBB VBB Sink/Source ± 0.5 mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C JA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm SOIC−8 SOIC−8 190 130 °C/W °C/W JC Thermal Resistance (Junction−to−Case) Standard Board SOIC−8 41 to 44 °C/W JA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm TSSOP−8 TSSOP−8 185 140 °C/W °C/W JC Thermal Resistance (Junction−to−Case) Standard Board TSSOP−8 41 to 44 °C/W Tsol Wave Solder 3 sec @ 248°C 3 sec @ 260°C 265 265 °C VI VCC VI VEE VCC − VEE 2.8 V VCC − VEE 2.8 V |D − D| Standard Pb−Free Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. http://onsemi.com 3 NB6L16 Table 4. DC CHARACTERISTICS, PECL VCC = 2.5 V, VEE = 0 V (Note 4) −40°C 25°C 85°C Characteristic Min Typ Max Min Typ Max Min Typ Max Unit IEE Negative Power Supply Current (Note 5) 10 12 18 10 12 18 10 12 18 mA VOH Output HIGH Voltage (Note 6) 1350 1450 1550 1400 1500 1600 1450 1550 1650 mV VOL Output LOW Voltage (Note 6) 565 725 870 630 765 920 690 825 970 mV Symbol DIFFERENTIAL INPUT DRIVEN SINGLE−ENDED (Figures 10, 12) Vth Input Threshold Reference Voltage Range (Notes 2, 7) 1125 VCC −75 1125 VCC −75 1125 VCC −75 mV VIH Single−Ended Input HIGH Voltage Vth +75 VCC Vth +75 VCC Vth +75 VCC mV VIL Single−Ended Input LOW Voltage VEE Vth −75 VEE Vth −75 VEE Vth −75 mV DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (Figures 11, 13) VIHD Differential Input HIGH Voltage 1200 VCC 1200 VCC 1200 VCC mV VILD Differential Input LOW Voltage VEE VCC −75 VEE VCC −75 VEE VCC −75 mV VCMR Input Common Mode Range (Differential Cross−Point Voltage) (Note 3) 1163 VCC −38 1163 VCC −38 1163 VCC −38 mV VID Differential Input Voltage (VIHD − VILD) 75 2500 75 2500 75 2500 mV IIH Input HIGH Current D D 150 150 A IIL Input LOW Current D D 50 10 −150 −150 150 150 −5 −30 50 10 −150 −150 −5 −30 150 150 50 10 −150 −150 −5 −30 A NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 2. Vth is applied to the complementary input when operating in single−ended mode. 3. VCMR minimum varies 1:1 with VEE, VCMR maximum varies 1:1 with VCC. 4. Input and output parameters vary 1:1 with VCC. VEE can vary +0.125 V to −1.3 V. 5. All input and output pins left open. 6. All loading with 50 to VCC − 2.0 V. 7. Do not use VBB as a reference voltage for single−ended PECL signals when operating device at VCC − VEE < 3.0 V. http://onsemi.com 4 NB6L16 Table 5. DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 10) Characteristic Min −40°C Typ Max Min 25°C Typ Max Min 85°C Typ Max Unit IEE Negative Power Supply Current (Note 11) 10 12 18 10 12 18 10 12 18 mA VOH Output HIGH Voltage (Note 12) 2150 2250 2350 2200 2300 2400 2250 2350 2450 mV VOL Output LOW Voltage (Note 12) 1365 1525 1670 1430 1565 1720 1490 1625 1770 mV Symbol DIFFERENTIAL INPUT DRIVEN SINGLE−ENDED (Figures 10, 12) Vth Input Threshold Reference Voltage Range (Note 8) 1125 VCC −75 1125 VCC −75 1125 VCC −75 mV VIH Single−Ended Input HIGH Voltage Vth +75 VCC Vth +75 VCC Vth +75 VCC mV VIL Single−Ended Input LOW Voltage VEE Vth −75 VEE Vth −75 VEE Vth −75 mV VBB Output Voltage Reference 1880 2070 1880 2070 1880 2070 mV 1980 1980 1980 DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (Figures 11, 13) VIHD Differential Input HIGH Voltage 1200 VCC 1200 VCC 1200 VCC mV VILD Differential Input LOW Voltage VEE VCC −75 VEE VCC −75 VEE VCC −75 mV VCMR Input Common Mode Range (Differential Cross−Point Voltage) (Note 9) 1163 VCC −38 1163 VCC −38 1163 VCC −38 mV VID Differential Input Voltage (VIHD − VILD) 75 2500 75 2500 75 2500 mV IIH Input HIGH Current D D 150 150 A IIL Input LOW Current D D 50 10 −150 −150 150 150 −5 −30 50 10 −150 −150 −5 −30 150 150 50 10 −150 −150 −5 −30 A NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 8. Vth is applied to the complementary input when operating in single−ended mode. 9. VCMR minimum varies 1:1 with VEE, VCMR maximum varies 1:1 with VCC. 10. Input and output parameters vary 1:1 with VCC. VEE can vary +0.925 V to −0.5 V. 11. All input and output pins left open. 12. All loading with 50 to VCC − 2.0 V. http://onsemi.com 5 NB6L16 Table 6. DC CHARACTERISTICS, NECL VCC = 0 V, VEE = −3.465 V to −2.375 V (Note 15) Min −40°C Typ Max Min 25°C Typ Max Min 85°C Typ Max Unit IEE Negative Power Supply Current (Note 17) 10 12 18 10 12 18 10 12 18 mA VOH Output HIGH Voltage (Note 16) −1150 −1050 −950 −1100 −1000 −900 −1050 −950 −850 mV VOL Output LOW Voltage (Note 16) −1935 −1775 −1630 −1870 −1735 −1580 −1810 −1675 −1530 mV Symbol Characteristic DIFFERENTIAL INPUT DRIVEN SINGLE−ENDED (Figures 10, 12) Vth Input Threshold Reference Voltage Range (Note 8) VEE +1125 VCC −75 VEE +1125 VCC −75 VEE +1125 VCC −75 mV VIH Single−Ended Input HIGH Voltage Vth +75 VCC Vth +75 VCC Vth +75 VCC mV VIL Single−Ended Input LOW Voltage VEE Vth −75 VEE Vth −75 VEE Vth −75 mV VBB Output Voltage Reference −1230 −1420 −1230 −1420 −1230 mV −1420 −1320 −1320 −1320 DIFFERENTIAL INPUTS DRIVEN DIFFERENTIALLY (Figures 11, 13) VIHD Differential Input HIGH Voltage VEE+ 1200 VCC VEE+ 1200 VCC VEE+ 1200 VCC mV VILD Differential Input LOW Voltage VEE VCC −75 VEE VCC −75 VEE VCC −75 mV VCMR Input Common Mode Range (Differential Cross−Point Voltage) (Note 9) VEE+ 1163 VCC −38 VEE+ 1163 VCC −38 VEE+ 1163 VCC −38 mV VID Differential Input Voltage (VIHD − VILD) 75 2500 75 2500 75 2500 mV IIH Input HIGH Current D D 150 150 A IIL Input LOW Current D D 50 10 −150 −150 150 150 −5 −30 50 10 −150 −150 −5 −30 150 150 50 10 −150 −150 −5 −30 A NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 13. Vth is applied to the complementary input when operating in single−ended mode. 14. VCMR minimum varies 1:1 with VEE, VCMR maximum varies 1:1 with VCC. 15. Input and output parameters vary 1:1 with VCC. 16. All loading with 50 to VCC − 2.0 V. 17. All input and output pins left open. http://onsemi.com 6 NB6L16 Table 7. AC CHARACTERISTICS VCC = 0 V; VEE = −3.465 V to −2.375 V or VCC = 2.375 V to 3.465 V; VEE = 0 V (Note 18) −40°C Symbol VOUTPP Characteristic 25°C Min Typ Max 500 270 700 350 80 130 180 3 30 85°C Min Typ Max Min Typ 500 270 700 350 80 130 180 25 60 3 30 0.2 1 2 12 Max 500 270 700 300 85 135 185 ps 25 60 3 30 25 60 ps 0.2 1 0.2 1 2 12 2 12 Output Voltage Amplitude mV fin < 3 GHz fin < 6 GHz (See Figures 2 & 3) Unit tPLH, tPHL Propagation Delay to Output Differential @ 1 GHz tSKEW Duty Cycle Skew (Note 19) Device−to−Device Skew tJITTER RMS Random Clock Jitter (Note 20) fin < 6 GHz Peak−to−Peak Data Dependent JItter (Note 21) fin < 6 Gb/s ps VINPP Input Voltage Swing / Sensitivity (Differential Configuration) (Note 22) 75 700 2500 75 700 2500 75 700 2500 mV tr tf Output Rise/Fall Times (20% − 80%) 30 70 120 30 70 120 30 70 120 ps Q, Q NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 18. Measured using a 800 mV source, 50% duty cycle clock source. All loading with 50 to VCC. Input edge rates 40 ps (20% − 80%). 19. See Figure 9 tskew = |tPLH − tPHL| for a nominal 50% differential clock input waveform. Skew is measured between outputs under identical transitions and conditions @ 1 GHz. 20. Additive RMS jitter with 50% duty cycle clock signal at 6 GHz. 21. Additive Peak−to−Peak data dependent jitter with NRZ PRBS 223−1 data rate at 6 Gb/s. 22. VINPP(max) cannot exceed VCC − VEE. (Applicable only when VCC − VEE < 2500 mV). Input voltage swing is a single−ended measurement operating in the differential mode. 0.8 OUTPUT VOLTAGE AMPLITUDE (V) OUTPUT VOLTAGE AMPLITUDE (V) 0.8 −40°C 0.7 0.6 0.5 25°C 0.4 85°C 0.3 0.2 0.1 0.7 −40°C 0.6 0.5 0.4 25°C 0.3 85°C 0.2 0.1 0.0 0.0 1 2 3 4 5 6 7 1 8 2 3 4 5 6 7 INPUT CLOCK FREQUENCY (GHz) INPUT CLOCK FREQUENCY (GHz) Figure 2. Output Voltage Amplitude (VOUTPP) versus Input Clock Frequency (fIN) and Temperature at VCC − VEE = 3.3 V Figure 3. Output Voltage Amplitude (VOUTPP) versus Input Clock Frequency (fIN) and Temperature at VCC − VEE = 2.5 V http://onsemi.com 7 8 OUTPUT VOLTAGE AMPLITUDE (100 mV/div) OUTPUT VOLTAGE AMPLITUDE (100 mV/div) NB6L16 TIME (62 ps/div) TIME (32 ps/div) Figure 4. Typical Output Waveform at 2.488 Gb/s with PRBS 223−1 (Total System Pk−Pk Jitter is 16 ps. Device Pk−Pk Jitter Contribution is 3 ps) VCC − VEE = 3.3 V; VIN = 700 mV; TA = 25°C. 190 120 180 110 RISE/FALL TIME (ps) 170 160 85°C 150 25°C 140 130 120 −40°C 110 100 100 85°C 90 25°C 80 70 60 50 −40°C 40 90 80 30 2.375 2.5 3.3 POWER SUPPLY VOLTAGE (V) 3.465 2.375 Figure 6. Propagation Delay versus Power Supply Voltage and Temperature 2.5 3.3 POWER SUPPLY VOLTAGE (V) 17 16 15 VCC − VEE = −3.465 V 14 13 12 VCC − VEE = −2.375 V 11 3.465 Figure 7. Rise/Fall Time versus Power Supply Voltage and Temperature 18 IEE CURRENT (mA) PROPAGATION DELAYS (ps) NOTE: Figure 5. Typical Output Waveform at 6.125 Gb/s with PRBS 223−1 (Total System Pk−Pk Jitter is 17 ps. Device Pk−Pk Jitter Contribution is 4 ps) 10 −40 25 TEMPERATURE (°C) Figure 8. IEE Current versus Temperature and Power Supply Voltage http://onsemi.com 8 85 NB6L16 D VINPP(D) = VIH(D) − VIL(D) VINPP(D) = VIH(D) − VIL(D) D Q VOUTPP(Q) = VOH(Q) − VOL(Q) VOUTPP(Q) = VOH(Q) − VOL(Q) Q tPHL tPLH Figure 9. AC Reference Measurement Vth D D D D Vth Figure 10. Differential Input Driven Single−Ended VCC Vthmax Figure 11. Differential Inputs Driven Differentially VCC VCMmax VIHmax VIHDmax VILDmax VID = VIHD − VILD VIHDtyp VILmax VIHTYP VthTYP VILTYP Vth VCMR VILDtyp VIHmin Vthmin GND GND Figure 12. Vth Diagram Q VIHDmin VILDmin VCMmax VILmin Figure 13. VCMR Diagram Zo = 50 D Receiver Device Driver Device Q Zo = 50 D 50 50 VTT VTT = VCC − 2.0 V Figure 14. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D − Termination of ECL Logic Devices.) http://onsemi.com 9 NB6L16 ORDERING INFORMATION Package Shipping† SO−8 98 Units / Rail NB6L16DG SO−8 (Pb−Free) 98 Units / Rail NB6L16DR2 SO−8 2500 / Tape & Reel NB6L16DR2G SO−8 (Pb−Free) 2500 / Tape & Reel NB6L16DT TSSOP−8 100 Units / Rail NB6L16DTG* TSSOP−8 (Pb−Free) 100 Units / Rail NB6L16DTR2 TSSOP−8 2500 / Tape & Reel NB6L16DTR2G* TSSOP−8 (Pb−Free) 2500 / Tape & Reel Device NB6L16D †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *Future Product − Contact factory for availability. Resource Reference of Application Notes AN1405/D − ECL Clock Distribution Techniques AN1406/D − Designing with PECL (ECL at +5.0 V) AN1503/D − ECLinPS I/O SPiCE Modeling Kit AN1504/D − Metastability and the ECLinPS Family AN1568/D − Interfacing Between LVDS and ECL AN1642/D − The ECL Translator Guide AND8001/D − Odd Number Counters Design AND8002/D − Marking and Date Codes AND8020/D − Termination of ECL Logic Devices AND8066/D − Interfacing with ECLinPS AND8090/D − AC Characteristics of ECL Devices http://onsemi.com 10 NB6L16 PACKAGE DIMENSIONS SOIC−8 D SUFFIX PLASTIC SOIC PACKAGE CASE 751−07 ISSUE AC −X− A 8 5 0.25 (0.010) S B 1 M Y M 4 K Y− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. G C N DIM A B C D G H J K M N S X 45 SEATING PLANE − 0.10 (0.004) H M D 0.25 (0.010) M Z Y S X J S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0 8 0.25 0.50 5.80 6.20 SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm inches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 11 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 8 0.010 0.020 0.228 0.244 NB6L16 PACKAGE DIMENSIONS TSSOP−8 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948R−02 ISSUE A 8x 0.15 (0.006) T U K REF 0.10 (0.004) S 2X L/2 8 1 PIN 1 IDENT S T U S V NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. S 5 0.25 (0.010) B −U− L 0.15 (0.006) T U M M 4 A −V− F DETAIL E C 0.10 (0.004) −T− SEATING PLANE D −W− G DETAIL E DIM A B C D F G K L M MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 0.80 1.10 0.05 0.15 0.40 0.70 0.65 BSC 0.25 0.40 4.90 BSC 0 6 INCHES MIN MAX 0.114 0.122 0.114 0.122 0.031 0.043 0.002 0.006 0.016 0.028 0.026 BSC 0.010 0.016 0.193 BSC 0 6 ECLinPS is a trademark of Semiconductor Components Industries, LLC. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 12 For additional information, please contact your local Sales Representative. NB6L16/D