ULTRA SLIMPAK® G408-0001 & G408-1001 DC Input Field Configurable Isolator Provides a Fully Isolated DC Output in Proportion to a DC Input Description Benefits Eliminates Ground Loops Field Configurable Input Ranges: 10mV to 100V, 1mA to 100mA Field Configurable Output Ranges: 0-5V, 0-10V, 0-1mA, 0-20mA, 4-20mA, ±5v, ±10V Ultra Slim Housing for High Density Installations Flexible Power Supply Accepts 9 to 30VDC ASIC Technology The Ultra SlimPak G408 is a DIN rail mount, DC input signal conditioner with 1800VDC isolation between input, output and power. The field configurable input and output offers flexible, wide ranging capability for DC current and voltage signals. The input can be configured for any one of 12 voltage ranges from 10mV to 100V or 6 current ranges from 1mA to 100mA (see Table 1). The output is linear to the input and can be set for either 0-5V, 0-10V, 0-1mA, 0-20mA or 4-20mA (for models G408-0001) and -5 to +5V or -10 to +10V (for model G408-1001). Wide ranging, precision zero and span pots allow 50% adjustability of offset and span turn-down within each of the 18 switch selectable ranges. For example, the 0-2mA input range could be turned down to 0-1mA and provide a full scale output signal (e.g. 4-20mA), or turned down and offset to achieve a 1-2mA/4-20mA I/O combination. The G408 also accepts bipolar inputs (e.g. 10V range set to bipolar = -10 to +10V) and offers selectable normal or reverse operation (e.g. 4-20mA/20-4mA). The ASIC based I/O channel is optically isolated to 1800VDC and is transformer isolated from the power supply. Application The G408 is useful in eliminating ground loops, converting signal levels, and providing signal drive. The field configurable, wide ranging capability ensures maximum flexibility for most DC to DC applications, minimizing spare part requirements. Diagnostic LED The G408 is equipped with a dual function LED signal monitor. The green, front mounted LED indicates both DC power and input signal status. Active DC power is indicated by an illuminated LED. If the input signal is more than 110% of the full scale range, the LED will flash at 8Hz. Below -10%, the flash rate is 4Hz. Figure 1: G408 Block Diagram Configuration Calibration The G408 has 18 input range settings. Trim potentiometers allow 50% input zero and span adjustability within each of the 18 full scale input ranges. 1. After configuring the DIP switches, connect the input to a calibrated DC source. Connect the output to the actual device load (or a load approximately equivalent to the device load) and apply power. Unless otherwise specified, the factory presets the Model G408-0001 and G408-1001 as follows: G408-0001 Input Range: Output Range: 4-20mA 4-20mA Note: To maximize thermal stability, final calibration should be performed in the operating installation, allowing approximately 1 to 2 hours for warm up and thermal equilibrium of the system. 2. Set the calibrator to the desired minimum input and adjust the zero potentiometer for the desired minimum output. 3. Set the calibrator to the desired maximum input and adjust the span potentiometer for the desired maximum output. 4. Repeat steps 2 and 3, as necessary, for best accuracy. G408-1001 Input Range: 4-20mA Output Range: -10 to +10V Table 1: G408 Input Range Settings The DC power input accepts any source between 9 and 30V; typically a 12V or 24VDC source is used (see Accessories). Ranges Voltage Current 20mV To minumize interference from electrical and magnetic fields, the use of shielded, twisted pair wires on the input and output is recommended. Refer to Tables 1 through 4 for the proper switch settings. Use the switches on SW1 to select the input type (voltage or current) and also to select the desired input range and function setting. Use SW2 to select the desired output type. 1 2 2mA 3 4 1 2 3 4 0 to 5V 0 to 10V 0 to 1mA 50mV 5mA 10mA 200mV 20mA 50mA 1V 100mA 2V 5V 10V 25V 50V 100V Unipolar Reverse 0 to 20mA Selector SW1 6 7 8 Table 4: G408-1001 Output Settings G408-1001 Ranges Selector SW1 9 -5V to +5V -10V to +10V Key: = 1 = ON or Closed 7 8 Current Voltage 4 to 20m 6 Table 2: G408 Function Settings 5 5 Key: = 1 = ON or Closed Key: = 1 = ON or Closed Function Selector SW2 G408-0001 Ranges 100mV 500mV WARNING! Do not change switch settings with power applied. Severe damage will result! Table 3: G408-0001 Output Settings Selector SW1 Key: = 1 = ON or Closed 10 Figure 2: G408-0001 Factory Cal; 4-20mA, Unipolar Input, Normal Operation, 4-20mA Output. Figure 3: G408-1001 Factory Cal; 4-20mA, Unipolar Input, Normal Operation -10 to 10V Output. Note: All Ultra SlimPak modules are designed to operate in ambient temperatures from 0 to 55°C when mounted on a horizontal DIN rail. If five or more modules are mounted on a vertical rail, circulating air or model HS01 Heat Sink is recommended. Refer to HS01 Technical Bulletin (#721-0549-00) or contact the factory for assistance. Figure 4: Wiring Diagram for G408-0001 and G408-1001 Figure 5: Mounting Multiple Modules SPECIFICATIONS Output (G408-1001) Voltage Output: -5V to +5V, -10 to +10V Source Impedance: <10 Ohms Drive: 10mA, max. LED Indication (green) Input Range >110%(approx) input:8Hz flash < -10%(approx) input: 4Hz flash Accuracy (Including Linearity, Hysteresis) <2mA/<20mV:± 0.35% of full scale, typical; 0.5%,max. >2mA/>20mV:± 0.1% of full scale, typical; 0.2%, max. Response Time (10-90%) 200mSec., typical Stability (Temperature) ±0.025% of full scale/°C,typical; ±0.05%/°C, max. Common Mode Rejection DC to 60Hz: 100dB Isolation (Input to Output) 1800VDC between input, output and power EMC Compliance (CE Mark) Emissions: EN50081-1 Immunity: EN50082-2 Safety: EN50178 Models & Accessories Dimensions Input Voltage Range Limits: 10mV to 100V Impedance: >100K Ohms Overvoltage: 400 Vrms, max.(Intermittent); 264 Vrms,max. (Continous) Current Range Limits: 1mA to 100mA Impedance: 20 Ohms, typical Overcurrent: 170mA RMS, max. Overvoltage: 60VDC Zero Turn-Up: 50% of full scale input Span Turn-Down: 50% of full scale input Common Mode (Input to Ground) 1800 VDC, max. Output (G408-0001) Voltage Output: 0-5V, 0-10V Source Impedance: <10 Ohms Drive: 10mA, max. Current Output: 0-1mA,4-20mA,0-20mA Source Impedance: >100K Ohms Compliance: 0-1mA: 7.5V, max (7.5K Ohms) 4-20mA: 12V, max (600 Ohms) 0-20mA: 12V, max (600 Ohms) Ordering Information Mean Time Between Failures 60K Hours Humidity (Non-Condensing) Operating: 15 to 95% @ 45°C Soak: 90% for 24 hours @ 65°C Temperature Range Operating: 0 to 55°C (32 to 131°F) Storage: -25 to 70°C (-13 to 158°F) Wire Terminals Screw terminals for 12-22AWG Power Consumption: 1.5W typical, 2.5W max. Range: 9 to 30VDC Weight 0.5 lbs. Agency Approvals CSA certified per standard C22.2, No. 0-M91 and 142-M1987 (File No. LR42272). UL recognized per standard UL508 (File No.E99775). CE Conformance per EMC directive 89/336/EEC and Low Voltage 73/23/EEC (Input < 75VDC, only). Specify: 1. Model: G408-0001 (standard outputs) or G408-1001 (bipolar outputs) 2. Accessories: (see Accessories) 3. Optional Custom Factory Calibration; specify C620 with desired input and output range. Accessories All SlimPak "G" series modules will mount on standard TS32 (model MD02) or TS35 (model MD03) DIN rail and include model HS01 heat sink. In addition, the following accessories are available: MD03 TS35x7.5 DIN rail WV905 24VDCPower Supply (0.5 Amp) H910 24VDC Power Supply (1 Amp) H915 24VDC Power Supply (2.3 Amp) MB03 End Bracket for MD03 C664 I/O Descriptive Tags C006 0.1 Ohm, 5W, 1% shunt resistor Factory Assistance For additional information on calibration, operation and installation contact our Technical Services Group: Eurotherm Controls 703-669-1318 741-F Miller Drive Leesburg, VA 20175-8993 703-443-0000 [email protected] actionio.com Action Instruments [email protected] 721-0657-00-F 09/04 Copyright© Eurotherm, Inc 2004 Barber-Colman Eurotherm Chessell Eurotherm Controls