IN-PHASE 4-WAY DIVIDERS/COMBINERS, POWER SERIES YF MODEL D418M SMA/TYPE N 0.5-18 GHz GENERAL SPECIFICATIONS Frequency Range: RF Impedance: RF Power: 0.5 to 18.0 GHz 50 Ohms The power handling capability for load VSWR ’s less than 1.50 is 1 watt CW and 1 kW peak for frequencies up to 2.0 GHz, and 400 mW CW and 0.4 kW peak for frequencies from 2.0 GHz to 18.0 GHz. –55°C to +85°C SMA or Type N Female Operating Temperature: Connectors: 0.10[2,54] C 0.38[9,7] 1.00 [25,4] A/2 C A/2 0.13[3,3] IN B/2 B OUT B OUT OUT OUT OUT 0.093[2,36] DIA. THRU 2 MOUNTING HOLES N FEMALE TYP. 0.38[9,7] TYP. SMA FEMALE TYP. A E TYP. B in [mm] 2.25 [57,2] C in [mm] 1.800 [45,72] D in [mm] 0.25 [6,4] E in [mm] 0.50 [12,7] 2 2.60 [66,0] 2.75 [69,9] 2.400 [60,96] 0.25 [6,4] 0.70 [17,8] 3 2.00 [50,8] 1.75 [44,5] 1.800 [45,72] 0.25 [6,4] 0.50 [12,7] 2.00 [50,8] 2.50 [63,5] 1.50 [38,1] 1.75 [44,5] 1.400 [35,56] 3.000 [76,2] 1.400 [35,56] 3.750 [95,25] 0.20 [5,1] 0.20 [5,1] 0.20 [5,1] 0.40 [10,2] 0.40 [10,2] 0.40 [10,2] 7 1.60 [40,6] 3.20 [81,3] 1.60 [40,6] 4.00 [101,6] — — 8 4.00 [101,6] 2.75 [69,9] 3.750 [95,25] — — 9 4.00 [101,6] 1.25 [31,8] 3.750 [95,25] — — 10 4.00 [101,6] 2.00 [50,8] 3.750 [95,25] — — 11 4.00 [101,6] 1.00 [25,4] 3.750 [95,25] — — 4 5 6 12 OUT OUT 0.50 [12,7] 1.00 [25,4] TYP. 0.74 [18,8] TYP. A FIGURE 2 SERIES YF-N A in [mm] 2.00 [50,8] 1 OUT D FIGURE 1 SERIES YF Outline 0.125[3,18] DIA. THRU 2 MTG. HOLES IN B/2 Drawing on Request ELECTRICAL PERFORMANCE 4 WAY TYPE Model No. SMA YF-23 YF-25 YF-51 YF-28 YF-54 YF-30 YF-38 YF-55 YF-45 D418M Type * N YF-23N YF-25N YF-51N YF-28N YF-54N YF-30N YF-38N YF-55N YF-45N — Frequency Maximum Range In/Out GHz VSWR 0.5-1.0 1.25/1.20 0.75-1.5 1.25/1.20 0.5-2.0 1.40/1.30 1.0-2.0 1.30/1.20 1.0-4.0 1.45/1.35 1.5-3.0 1.30/1.20 2.0-4.0 1.30/1.20 2.0-8.0 1.50/1.40 4.0-8.0 1.40/1.30 1.0-1.5 1.80/1.35 1.5-2.0 1.80/1.35 2.0-4.0 1.80/1.45 4.0-8.0 1.80/1.45 8.0-12.0 1.70/1.45 12.0-16.0 1.70/1.45 16.0-18.0 1.80/1.45 Maximum Insertion Loss dB 0.5 0.5 1.0 0.5 1.0 0.6 0.8 1.2 1.0 0.7 0.8 1.0 1.2 1.4 1.8 2.0 Minimum Isolation dB 20 20 18** 20 18 20 18 16 18 10 14 17 17 17 15 12 Phase Amplitude Balance Balance Degrees dB 3 0.3 3 0.3 4 0.4 3 0.3 4 0.4 3 0.3 3 0.3 5 0.5 5 0.5 1 0.2 2 0.2 4 0.3 6 0.4 10 0.5 13 0.6 15 0.6 Out- Outline line SMA N 1 7 2 8 2 8 3 7 4 9 5 7 6 7 1 10 6 11 12 — * Units with Type N connectors: up to 4GHz multiply VSWR’s by 1.05 and subtract 2 dB from isolation. Above 4GHz multiply VSWR’s by 1.10 and subtract 3dB from isolation. ** Greater than 30 dB over most of the frequency band. KE Y : Inches[Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25] An MCE Company TRIANGLE CORPORATION 60 South Jefferson Road, Whippany, NJ 07981 Tel: 973-887-8100 • Fax: 973-884-0445 E-Mail: [email protected] See us on the web @ www.kditriangle.com 10/98 4 WAY DIVIDER/COMBINERS, POWER ELECTRICAL SPECIFICATIONS .38 [9,7] 6.00[152,4] Model: D354KS Connectors: Type N Frequency Range: 860-900 MHz VSWR: 1.30:1 Maximum Isolation: 20 dB Minimum Insertion Loss: 6.5 dB Maximum RF Power: 50mW Maximum into each port .50 [12,7] 2.00[50,8] PRESS IN TYPE N FEM MATES WITH N MALE CONN PER MIL-C-39012 5 PLS 1.00[25,4] TYP .59 [14,99] Amplitude Balance: ±0.3 dB Maximum Phase Balance: ±3.0° Maximum Operating Temperature: –30° C to +70° C RF OUT J4 D349LS SMA Frequency Range: 800-900 MHz VSWR: 1.3:1 Maximum Isolation: 20 dB Minimum J1 2.75 [69,9] .190[4,83] Ø THRU 4 PLS. .13 [3,30] .13 [3,30] .75 [19,1] 5.75[146,1] .50[12,7] MAX. 5 PLS 2.875[73,03] .38[9,65] 5 PLS ELECTRICAL SPECIFICATIONS Connectors: J2 KDI 64537 D354KS D/C 3.00 [76,2] .80 [20,3] Model: J3 2.625[66,68] .13 [3,30] .13 [3,30] .50[12,7] 1 2.00 [50,8] 1.00[25,4] 2 4.00 [101,6] Insertion Loss: 0.5 dB Maximum RF Power: 50mW Maximum into each port KDI 64537 D349LS D/C 1.00[25,4] 3.75 [95,3] RF OUT 3 Amplitude Balance: ±1 dB Maximum Phase Balance: ±2.0° Maximum Operating Temperature: –30° C to +70° C 1.00[25,4] 4 MATES WITH SMA MALE CONN PER MIL-C-39012 5 PLACES .166[4,22] DIA. THRU 4 PLS .125[3,18] DIA. 4 MTG. HOLES .50[12,7] ELECTRICAL SPECIFICATIONS 2.50[63,5] Model: D307MS 2.240[56,9] Connectors: SMA Frequency Range: 824-925 MHz VSWR: .25[6,4] .13[3,30] .13[3,30] .27[6,86] INPUT J1 1.2:1 Maximum Isolation: 20 dB Minimum Insertion Loss: 6.3 dB Maximum (inc. div. loss) Amplitude Balance: ±0.1 dB Maximum Phase Balance: ±2° Maximum RF Power: 4.0 Watts CW Total @ Input Operating Temperature: –30° C to +70° C KDI 64537 D307MS D/C J2 J3 J4 1.740 [44,2] J5 .50 [12,7] MATE WITH SMA MALE CONN PER MIL-C-39012 5 PLACES 1.00[25,4] 1.50[38,1] 2.00[50,8] KE Y : Inches[Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25] 10/98 An MCE Company TRIANGLE CORPORATION 60 South Jefferson Road, Whippany, NJ 07981 Tel: 973-887-8100 • Fax: 973-884-0445 E-Mail: [email protected] See us on the web @ www.kditriangle.com 2.00 [50,8] 4 WAY DIVIDER/COMBINERS, POWER ELECTRICAL SPECIFICATIONS Model: Connectors: Frequency Range: VSWR: Isolation: Insertion Loss: RF Power: Amplitude Balance: Phase Balance: Operating Temperture: 4.00[101,6] 3.500[88,9] .25 [6,4] D331MS Type N 800-960 MHz Out 2.0:1 Maximum—unterminated input 1.6:1 Maximum—terminated input 15 dB Minimum output to input 20 dB Minimum output to output –8.0 dB Maximum (incl. divide loss) 2 Watts Maximum ±0.5 dB Maximum ±2° Maximum –30° to +70°C .270[6,86] DIA. THRU 2 MTG HOLES .750 [19,1] 2.00[50,8] .59 [14,99] .88 [22,35] KDI 64537 D331MS D/C 2.85 [72,4] .69[17,53] TYP 6 PLS MATES WITH TYPE`N`MALE CONN PER MIL-C-39012 5 PLS .375[9,53] .375[9,53] 1.000 [25,4] TYP 2 MTG HOLES 5 CONN`S 3.000[76,2] M4x0.7 LOCKING INSERT, 2 PLCS MTG SCREW SHALL NOT EXTEND MORE THAN .20[5,1] INTO COMPONENT, C'SINK 90° TO .220[5,59] DIA. .005 DIA M PRESS IN TYPE SMA FEM MATES WITH SMA MALE CONN PER MIL-C-39012 4 PLS. Coupling: Amplitude Balance: Phase Balance: RF Power: Operating Temperture: J5 .80[20,3] MATES WITH BNC MALE CONN PER MIL-C-39012 4.00[101,6] PRESS IN ‘N’ FEM CONN MATES WITN ‘N’ MALE PER MIL-C-39012 .65 [16,51] .65[16,51] TYP 3 PLS J5 D366KS See Outline 800–900 MHz 1.35:1 Maximum 6.6 dB Maximum 24.0 dB Minimum J2-J3, J4-J5 –40 dB Minimum (Coupler) J1-J6 29 dB Minimum All Other Combiner Combinations –20 ± .5 dB ±0.5 dB Maximum ±2° Maximum 2 Watts Maximum –30° to +70°C J4 J3 J2 J1 3.00[76,2] 2.750[69,91] KDI 64537 D36KS D/C J6 1.00[25,4] .13 [3.30] .190[0,483] DIA THRU 4 PLS .13[3.30] 3.750[95,3] 1.00 [25,4] 50Ω .59[14,99] 20 dB Coupler B J1 N J6 SCHEMATIC 2 Way Div 2 Way Div S J2 2 Way Div S J3 ELECTRICAL SPECIFICATIONS Model: Connectors: Frequency Range: D317NS SMA 800–2000 MHz Insertion Loss: 1.2 Maximum above 6 dB .58 [14,7] Isolation: 30 dB typ. 23 dB Minimum In: Out:: Phase Balance: ±2˚ Maximum RF Power: +20 dBm Maximum Operating Temperture: Housing Material:: –30° to +70°C Metalized Plastic RF OUT 3.00 2.600 [76,2] [66,04] 1.15 Maximum typ. 0.3 dB Maximum 1.50 [38,1] RF IN KDI 64537 D317NS S/N D/C S J4 S J5 MATES WITH SMA MALE CONN (5) PER MIL-C-39012 .29 [7,4] 3.00 [76,2] 1.50 [38,1] 1.25 Maximum typ. Amplitude Balance: .20 [5,1] .29 [7,4] VSWR: .50 [12,7] .67[17,02] MAX. .26[6,60] ELECTRICAL SPECIFICATIONS Model: Connectors: Frequency Range: VSWR: INS Loss: Isolation: J4 .50 [12,7] J3 1.00 [25,4] J2 The Model D366KS includes an equal four way power divider with Type N input and 4 SMA outputs. An isolated monitor port directional coupler with a BNC output connector is provided with a closely calibrated 20dB coupling value. Stripline construction and KDI high power Berrylium Oxide resistors employed in the design can readily be adapted to new custom applications. J1 GENERAL INFORMATION RF OUT .56 [14,2] 1.19 [30,2] 1.81 [46,0] 2.44 [62,0] RF OUT RF OUT .12[3,1] DIA. HOLES 2 PLS. KE Y : Inches[Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25] An MCE Company TRIANGLE CORPORATION 60 South Jefferson Road, Whippany, NJ 07981 Tel: 973-887-8100 • Fax: 973-884-0445 E-Mail: [email protected] See us on the web @ www.kditriangle.com 10/98 6 WAY DIVIDERS/COMBINERS, POWER ELECTRICAL SPECIFICATIONS Model: Connectors: Frequency Range: VSWR: Isolation: Insertion Loss: RF Power: Amplitude Balance: Phase Balance: Operating Temperture: .50 [12,7] D315MS SMA 800-900 MHz 1.3:1 Maximum 24 dB Minimum 15.5 dB ± 0.25 dB 30 dBm Maximum @ (J1) Port ± 0.5 dB Maximum ± 3° Maximum –30° to +70°C SCHEMATIC DIAGRAM KDI 64537 D315MS D/C 2.00 [50,8] J7 J6 J5 .56 [14,22] J4 J3 Amplitude Balance: Phase Balance: Operating Temperture: J7 J6 J5 J4 J3 J2 J1 .25 [6,4] MATE WITH SMA MALE CONNECTOR PER MIL-C-39012 (7) PLACES .20 [5,1] #6-32 UNC-2B ACCEPT #6-32 UNC-2A X .31[7,87] (2) PLACES 4.600[116,8] 5.00[127,0] 5.750[146,1] D365MS SMA 400-2000 MHz 1.5 dB 14 dB Minimum 1.35:1 Maximum 1 Watt Maximum @ Input Port 100 milliwatts Maximum/Port as a Combiner ± 0.7 dB Maximum ± 5° Maximum –30° to +70°C MATES WITH SMA MALE CONNECTOR PER MIL-C-39012 7 PLCS 3.00[76,2] .12 [3,05] 0.125[3,18] DIA 2 PLS KDI 64537 D365MS S/N D/C 4.00 [101,6] 2.000 [50,8] 1.00 [25,4] TYP .50 [12,7] .56 [14,22] .24 [6,10] 6.00[152,4] .125[3,18] DIA. 4 MTG. HOLES ELECTRICAL SPECIFICATIONS Model: Connectors: Frequency Range: VSWR: Isolation: Insertion Loss: RF Power: Amplitude Balance: Phase Balance: Operating Temperture: .27[6,86] TYP 7 PLACES J1 .75 [19,1] .63[16,0] (5) PLACES ELECTRICAL SPECIFICATIONS Model: Connectors: Frequency Range: Insertion Loss above 7.8 dB: Isolation: VSWR: RF Power: J2 .50[12,7] 3.50[88,9] D308MS SMA 824-925 MHz 1.2:1 Maximum 20 dB Minimum 8.2 dB Maximum (incl. div. loss) 4.0 Watts CW Total @ input ± 0.5 dB Maximum ± 3° Maximum –30° to +70°C .25[6,4] .13[3,3] 3.240[82,3] .13[3,3] .27[6,86] INPUT J1 KDI 64537 D308MS D/C J2 J3 J4 J5 1.740 [44,2] J6 2.00 [50,8] J7 MATE WITH SMA MALE CONN PER MIL-C-39012 7 PLACES .50 [12,7] 1.00[25,4] 1.50[38,1] 2.00[50,8] 2.50[63,5] 3.00[76,2] 6.00[152,4] ELECTRICAL SPECIFICATIONS Model: Connectors: Frequency Range: VSWR: Isolation: Insertion Loss: RF Power: Amplitude Balance: Phase Balance: Operating Temperture: .25 [6,4] D357KS Type N 800-960 MHz 1.35:1 Maximum all ports 20.0 dB Minimum 9.0 dB Maximum (incl. divide loss) 5 W Maximum ± 0.5 dB Maximum ± 3° Maximum –30° to +70°C 5.500[139,7] 3.00[76,2] .75 [19,1] .270[6,86] DIA. THRU 2 MTG HOLES CV90-14333-1 REL 12 .88 [22,35] 1.62 [41,15] MFG KDI 64537 D357KS D/C .59 [14,99] 1.000 [25,4] 5 PLS .50 [12,7] MATES WITH TYPE`N`MALE CONN PER MIL-C-39012 7 PLS .38[9,7] TYP 1.00 [25,4] 2.000[5,1] 4.000[101,6] M4x0.7[17,8] LOCKING INSERT, 3 PLCS MTG SCREW SHALL NOT EXTEND MORE THAN .20[5,1] INTO COMPONENT CSINK 90° TO .220[5,59] DIA. KEY: Inches[Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25] 10/98 An MCE Company TRIANGLE CORPORATION 60 South Jefferson Road, Whippany, NJ 07981 Tel: 973-887-8100 • Fax: 973-884-0445 E-Mail: [email protected] See us on the web @ www.kditriangle.com 6 WAY DIVIDERS/COMBINERS, POWER SUBASSEMBLY—WITH VARIABLE ATTENUATORS GENERAL INFORMATION .44 [11,18] The Model D387LS power divider subassembly incorporates unique level set adjustable attenuators, each with a minimum adjustment range of 0-12dB. Resistor isolated Wilkinson power dividers provide for high isolation between signal paths, and include a power monitor function. The stripline construction provided throughout can be readily modified for other custom applications. ATTENUATOR TRIM 6 PL .61 [15,49] .60[15,2] TYP. .90 [22,9] MATES WITH TYPE ‘N’ MALE CONNECTOR PER MIL-C-39012 6 PL 7.68[195,07] MAX. 7.250[184,2] .37[9,40] 1.20[30,5] TYP. ELECTRICAL SPECIFICATIONS Model: Connectors: D387LS Type N Output SMA Input BNC Monitor Port Frequency Range: 0.865 – 0.900 GHz Insertion Loss: 14.5 ±0.5 dB at 0 dB Trim 3.0 +.5 –0 dB Attenuator Trim: 0 to 12 dB Minimum (Screwdriver) RF Power: +17 dBM Isolation: 20 dB Minimum at 0 dB Trim VSWR (All Ports): 1.60:1 Maximum Operating Temperature: –30° to +70°C. DIV 3 WAY DIV 2 WAY DIV 2 WAY DIV 3 WAY J1 J7 VAR ATTEN ATTEN VAR ATTEN ATTEN J6 VAR ATTEN ATTEN J5 VAR ATTEN ATTEN J4 VAR ATTEN ATTEN RF Power: Amplitude Balance: Phase Balance: Operating Temperature: J5 J4 J3 J2 J3 VAR ATTEN ATTEN J2 3.00 [76,2] KDI 64537 D387LS D/C 2.750 [69,9] –3 DB MON J1 MON .19[4,83] DIA, 4 PLS 2.88[73,15] 5.38[136,65] MATES WITH TYPE ‘SMA’ MALE CONNECTOR PER MIL-C-39012 ELECTRICAL SPECIFICATIONS Model: Connectors: Frequency Range: VSWR: Isolation: Insertion Loss: J6 J7 MATES WITH TYPE ‘BNC’ MALE CONNECTOR PER MIL-C-39012 6.00[152,4] D390MS SMA/N 824-894 MHz 1.2:1 Maximum 20.0 dB Minimum 8.5 dB Maximum (Includes divide loss) 500 milliwatts Maximum @ Combined Port ±0.2 dB Maximum ±0.2 Maximum –30° to +70°C. .25 [6,4] 3.00[76,2] 1.50 [38,1] KDI 64537 D390MS D/C J1 J7 J6 J5 J4 MATES WITH SMA MALE CONN PER MIL-C-39012 .38 [9,7] .270[6,86] DIA. THRU 2 MTG. HOLES .75 [19,1] .26 [6,6] J3 J2 .59 [14,99] MATES WITH TYPE`N`MALE CONN PER MIL-C-39012 6 PLS .50 [12,7] 1.000 [25,4] 5 PLS ELECTRICAL SPECIFICATIONS D333KS .860-.900 GHz 1.35:1 Maximum >27 dB J5-J6 (J1, J2, J3, J4 & J7 Open) 20 dB Minimum all other Insertion Loss: 12.0 ± .4 dB (J7-J1, J7-J2) Coupling: 10.0 ± .5 dB (J5-J1) Path Loss: 4.5 dB Maximum (4.1 dB Typical) (J7-J6) RF Power: 50mW Maximum each input Operating Temperature: –30° to +70°C. Port Designations above indicate (RF OUT — RF IN) .75 [19,1] 5.500±.005[140,0±0,13] PRESS IN SMA FEM CONN MATES WITN SMA MALE PER MIL-C-39012 (SEE NOTE 1) Model: Frequency: VSWR: Isolation: .38[9,65] (7 PLS) 6.00[152,4] .50 [12,7] 1.000[25,4] TYP .59[14,99] J6 3.00 [76,2] J5 J4 J3 J2 J1 KDI 64537 D333KS D/C J7 1.50 [38,1] .190[4,83] THRU 4 PLS. .13[3,3] .27 [6,86] 5.750[146,1] PRESS IN TYPE N FEM MATES WITH N MALE CONN PER MIL-C-39012 6 PLS. (SEE NOTE 2) 2.750 [69,9] .13 [3,3] .75 [19,1] Notes: 1. Connector SMA: Passivated Stainless Steel ASTM-A-582 (QQ-S-764) Body with Gold Plated (MIL-G-45204 Type II, Class I, Grade C) 2. Connector N: Nickel Plated (QQ-N-290) over CU. Strike (MIL-C-14550) over Brass Body 1/2 HD Comp 22 (QQ-B-626) 3. HSG: Chem Film (MIL-C-5541) Class 1A over Aluminum 6061-T6 per (QQ-A-250) KEY: Inches[Millimeters] .XX ±.03 .XXX ±.010 [.X ±0.8 .XX ±0.25] An MCE Company TRIANGLE CORPORATION 60 South Jefferson Road, Whippany, NJ 07981 Tel: 973-887-8100 • Fax: 973-884-0445 E-Mail: [email protected] See us on the web @ www.kditriangle.com 10/98