IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI 2M x 8 HIGH-SPEED CMOS STATIC RAM ® PRELIMINARY INFORMATION JANUARY 2006 FEATURES DESCRIPTION • High-speed access times: 8, 10, 20 ns • High-performance, low-power CMOS process • Multiple center power and ground pins for greater noise immunity • Easy memory expansion with CE and OE options • CE power-down • Fully static operation: no clock or refresh required • TTL compatible inputs and outputs • Single power supply – VDD 1.65V to 2.2V (IS61WV20488ALL) speed = 20ns for Vcc = 1.65V to 2.2V – VDD 2.4V to 3.6V (IS61/64WV20488BLL) speed = 10ns for Vcc = 2.4V to 3.6V speed = 8ns for Vcc = 3.3V + 5% • Packages available: – 48-ball miniBGA (9mm x 11mm) – 44-pin TSOP (Type II) • Industrial and Automotive Temperature Support • Lead-free available The ISSI IS61WV20488ALL/BLL and IS64WV20488BLL are very high-speed, low power, 2M-word by 8-bit CMOS static RAM. The IS61WV20488ALL/BLL and IS64WV20488BLL are fabricated using ISSI's highperformance CMOS technology. This highly reliable process coupled with innovative circuit design techniques, yields higher performance and low power consumption devices. When CE is HIGH (deselected), the device assumes a standby mode at which the power dissipation can be reduced down with CMOS input levels. The IS61WV20488ALL/BLL and IS64WV20488BLL operate from a single power supply and all inputs are TTL-compatible. The IS61WV20488ALL/BLL and IS64WV20488BLL are available in 48 ball mini BGA and 44-pin TSOP (Type II) packages. FUNCTIONAL BLOCK DIAGRAM A0-A20 DECODER 2M X 8 MEMORY ARRAY I/O DATA CIRCUIT COLUMN I/O VDD GND I/O0-I/O7 CE OE CONTROL CIRCUIT WE Copyright © 2006 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 1 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® PIN CONFIGURATION 48-pin Mini BGA (M ) (9mm x 11mm) 1 2 3 4 5 44-pin TSOP (Type II ) 6 A NC OE A0 A1 A2 NC B NC NC A3 A4 CE I/O0 C NC NC A5 A6 I/O1 I/O2 D GND NC A17 A7 I/O3 VDD E VDD NC NC A16 I/O4 GND F NC NC A14 A15 I/O5 I/O6 G NC A19 A12 A13 WE I/O7 H A18 A8 A9 A10 A11 A20 NC NC A0 A1 A2 A3 A4 CE I/O0 I/O1 VDD GND I/O2 I/O3 WE A5 A6 A7 A8 A9 NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 NC NC A20 A18 A17 A16 A15 OE I/O7 I/O6 GND VDD I/O5 I/O4 A14 A13 A12 A11 A10 A19 NC NC PIN DESCRIPTIONS 2 A0-A20 Address Inputs CE Chip Enable Input OE Output Enable Input WE Write Enable Input I/O0-I/O7 Data Input / Output VDD Power GND Ground NC No Connection Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® TRUTH TABLE Mode WE Not Selected (Power-down) Output Disabled Read Write CE OE I/O Operation VDD Current X H X High-Z ISB1, ISB2 H H L L L L H L X High-Z DOUT DIN ICC ICC ICC ABSOLUTE MAXIMUM RATINGS(1) Symbol VTERM VDD TSTG PT Parameter Terminal Voltage with Respect to GND VDD Relates to GND Storage Temperature Power Dissipation Value –0.5 to VDD + 0.5 –0.3 to 4.0 –65 to +150 1.0 Unit V V °C W Notes: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. CAPACITANCE(1,2) Symbol Parameter CIN Input Capacitance CI/O Input/Output Capacitance Conditions Max. Unit VIN = 0V 6 pF VOUT = 0V 8 pF Notes: 1. Tested initially and after any design or process changes that may affect these parameters. 2. Test conditions: TA = 25°C, f = 1 MHz, VDD = 3.3V. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 3 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® OPERATING RANGE (VDD) (IS61WV20488ALL) Range Ambient Temperature Commercial 0°C to +70°C Industrial –40°C to +85°C Automotive –40°C to +125°C VDD (20 nS) 1.65V-2.2V 1.65V-2.2V 1.65V-2.2V OPERATING RANGE (VDD) (IS61WV20488BLL)(1) Range Ambient Temperature Commercial 0°C to +70°C Industrial –40°C to +85°C VDD (8 nS) 3.3V + 5% 3.3V + 5% VDD (10 nS) 2.4V-3.6V 2.4V-3.6V Note: 1. When operated in the range of 2.4V-3.6V, the device meets 10ns. When operated in the range of 3.3V + 5%, the device meets 8ns. OPERATING RANGE (VDD) (IS64WV20488BLL) Range Automotive 4 Ambient Temperature –40°C to +125°C VDD (10 nS) 2.4V-3.6V Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® DC ELECTRICAL CHARACTERISTICS (Over Operating Range) VDD = 3.3V + 5% Symbol Parameter Test Conditions Min. Max. Unit VOH Output HIGH Voltage VDD = Min., IOH = –4.0 mA 2.4 — V VOL Output LOW Voltage VDD = Min., IOL = 8.0 mA — 0.4 V VIH Input HIGH Voltage VIL Input LOW Voltage(1) 2 VDD + 0.3 V –0.3 0.8 V ILI Input Leakage GND ≤ VIN ≤ VDD –1 1 µA ILO Output Leakage GND ≤ VOUT ≤ VDD, Outputs Disabled –1 1 µA Min. Max. Unit Note: 1. VIL (min.) = –0.3V DC; VIL (min.) = –2.0V AC (pulse width - 2.0 ns). Not 100% tested. VIH (max.) = VDD + 0.3V DC; VIH (max.) = VDD + 2.0V AC (pulse width - 2.0 ns). Not 100% tested. DC ELECTRICAL CHARACTERISTICS (Over Operating Range) VDD = 2.4V-3.6V Symbol Parameter Test Conditions VOH Output HIGH Voltage VDD = Min., IOH = –1.0 mA 1.8 — V VOL Output LOW Voltage VDD = Min., IOL = 1.0 mA — 0.4 V VIH Input HIGH Voltage 2.0 VDD + 0.3 V VIL Input LOW Voltage(1) –0.3 0.8 V ILI Input Leakage GND ≤ VIN ≤ VDD –1 1 µA ILO Output Leakage GND ≤ VOUT ≤ VDD, Outputs Disabled –1 1 µA Note: 1. VIL (min.) = –0.3V DC; VIL (min.) = –2.0V AC (pulse width - 2.0 ns). Not 100% tested. VIH (max.) = VDD + 0.3V DC; VIH (max.) = VDD + 2.0V AC (pulse width - 2.0 ns). Not 100% tested. DC ELECTRICAL CHARACTERISTICS (Over Operating Range) VDD = 1.65V-2.2V Symbol Parameter Test Conditions VDD Min. Max. Unit VOH Output HIGH Voltage IOH = -0.1 mA 1.65-2.2V 1.4 — V VOL Output LOW Voltage IOL = 0.1 mA 1.65-2.2V — 0.2 V VIH Input HIGH Voltage 1.65-2.2V 1.4 VDD + 0.2 V VIL(1) Input LOW Voltage 1.65-2.2V –0.2 0.4 V ILI Input Leakage GND ≤ VIN ≤ VDD –1 1 µA ILO Output Leakage GND ≤ VOUT ≤ VDD, Outputs Disabled –1 1 µA Note: 1. VIL (min.) = –0.3V DC; VIL (min.) = –2.0V AC (pulse width - 2.0 ns). Not 100% tested. VIH (max.) = VDD + 0.3V DC; VIH (max.) = VDD + 2.0V AC (pulse width - 2.0 ns). Not 100% tested. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 5 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® AC TEST CONDITIONS (HIGH SPEED) Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Level (VRef) Output Load Unit (2.4V-3.6V) 0.4V to VDD-0.3V 1.5ns VDD/2 Unit (3.3V + 5%) 0.4V to VDD-0.3V 1.5ns VDD/2 + 0.05 Unit (1.65V-2.2V) 0.4V to VDD-0.2V 1.5ns VDD/2 See Figures 1 and 2 See Figures 1 and 2 See Figures 1 and 2 AC TEST LOADS 319 Ω ZO = 50Ω 3.3V 50Ω 1.5V OUTPUT OUTPUT 30 pF Including jig and scope Figure 1. 6 5 pF Including jig and scope 353 Ω Figure 2. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) -8 Symbol Parameter Test Conditions ICC VDD = Max., IOUT = 0 mA, f = fMAX ICC1 VDD Dynamic Operating Supply Current Min. Max. Com. Ind. Auto. typ.(2) — — — 120 125 — -10 Min. Max. — — — -20 Min. Max. Unit 95 100 140 — — — 90 100 140 mA 60 Operating Supply Current VDD = Max., IOUT = 0 mA, f = 0 Com. Ind. Auto. — — — 35 35 — — — — 30 40 60 — — — 30 40 70 mA ISB1 TTL Standby Current (TTL Inputs) VDD = Max., VIN = VIH or VIL CE ≥ VIH, f = 0 Com. Ind. Auto. — — — 30 35 — — — — 30 35 70 — — — 30 35 70 mA ISB2 CMOS Standby Current (CMOS Inputs) VDD = Max., CE ≥ VDD – 0.2V, VIN ≥ VDD – 0.2V, or VIN ≤ 0.2V, f = 0 Com. Ind. Auto. typ.(2) — — — 20 25 — — — — 20 25 70 — — — 15 20 70 mA 4 Note: 1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change. 2. Typical values are measured at VDD = 3.0V, TA = 25oC and not 100% tested. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 7 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range) -8 Symbol tRC tAA tOHA tACE tDOE tHZOE(2) tLZOE(2) tHZCE(2 tLZCE(2) tPU tPD Parameter -10 Min. Max. Min. Max. Unit Read Cycle Time 8 — 10 — ns Address Access Time — 8 — 10 ns Output Hold Time 2 — 2 — ns CE Access Time — 8 — 10 ns OE Access Time — 5.5 — 6.5 ns OE to High-Z Output — 3 — 4 ns OE to Low-Z Output 0 — 0 — ns CE to High-Z Output 0 3 0 4 ns CE to Low-Z Output 3 — 3 — ns Power Up Time 0 — 0 — ns Power Down Time — 8 — 10 ns Notes: 1. Test conditions assume signal transition times of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0V to 3.0V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. 8 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range) Symbol Parameter -20 ns Min. Max. Unit tRC Read Cycle Time 20 — ns tAA Address Access Time — 20 ns tOHA Output Hold Time 2.5 — ns tACE CE Access Time — 20 ns tDOE OE Access Time — 8 ns tHZOE(2) OE to High-Z Output 0 8 ns tLZOE OE to Low-Z Output 0 — ns (2 tHZCE CE to High-Z Output 0 8 ns (2) tLZCE CE to Low-Z Output 3 — ns tPU Power Up Time 0 — ns tPD Power Down Time — 20 ns (2) Notes: 1. Test conditions assume signal transition times of 1.5 ns or less, timing reference levels of 1.25V, input pulse levels of 0.4V to VDD-0.3V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. 3. Not 100% tested. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 9 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® AC WAVEFORMS READ CYCLE NO. 1(1,2) (Address Controlled) (CE = OE = VIL) t RC ADDRESS t AA t OHA t OHA DOUT DATA VALID PREVIOUS DATA VALID READ1.eps READ CYCLE NO. 2(1,3) (CE and OE Controlled) t RC ADDRESS t AA t OHA OE t HZOE t DOE t LZOE CE t ACE t HZCE t LZCE DOUT HIGH-Z DATA VALID CE_RD2.eps Notes: 1. WE is HIGH for a Read Cycle. 2. The device is continuously selected. OE, CE = VIL. 3. Address is valid prior to or coincident with CE LOW transitions. 10 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® WRITE CYCLE SWITCHING CHARACTERISTICS(1,3) (Over Operating Range) -8 Symbol Parameter -10 Min. Max. Min. Max. Unit tWC Write Cycle Time 8 — 10 — ns tSCE CE to Write End 6.5 — 8 — ns tAW Address Setup Time to Write End 6.5 — 8 — ns tHA Address Hold from Write End 0 — 0 — ns tSA Address Setup Time 0 — 0 — ns tPWE1 WE Pulse Width (OE = HIGH) 6.5 — 8 — ns tPWE2 WE Pulse Width (OE = LOW) 8.0 — 10 — ns tSD Data Setup to Write End 5 — 6 — ns tHD Data Hold from Write End 0 — 0 — ns (2) tHZWE WE LOW to High-Z Output — 3.5 — 5 ns (2) tLZWE WE HIGH to Low-Z Output 2 — 2 — ns Notes: 1. Test conditions assume signal transition times of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0V to 3.0V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. 3. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the write. Shaded area product in development Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 11 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® WRITE CYCLE SWITCHING CHARACTERISTICS(1,2) (Over Operating Range) Symbol Parameter -20 ns Min. Max. Unit tWC Write Cycle Time 20 — ns tSCE CE to Write End 12 — ns tAW Address Setup Time to Write End 12 — ns tHA Address Hold from Write End 0 — ns tSA Address Setup Time 0 — ns tPWE1 WE Pulse Width (OE = HIGH) 12 — ns tPWE2 WE Pulse Width (OE = LOW) 17 — ns tSD Data Setup to Write End 9 — ns tHD Data Hold from Write End 0 — ns (3) tHZWE WE LOW to High-Z Output — 9 ns tLZWE(3) WE HIGH to Low-Z Output 3 — ns Notes: 1. Test conditions assume signal transition times of 1.5ns or less, timing reference levels of 1.25V, input pulse levels of 0.4V to VDD-0.3V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. 3. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the write. 12 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® AC WAVEFORMS WRITE CYCLE NO. 1(1,2) (CE Controlled, OE = HIGH or LOW) t WC VALID ADDRESS ADDRESS t SA t SCE t HA CE t AW t PWE1 t PWE2 WE t HZWE DOUT DATA UNDEFINED t LZWE HIGH-Z t SD DIN t HD DATAIN VALID CE_WR1.eps Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 13 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® AC WAVEFORMS WRITE CYCLE NO. 2(1,2) (WE Controlled: OE is HIGH During Write Cycle) t WC ADDRESS VALID ADDRESS t HA OE CE LOW t AW t PWE1 WE t SA DOUT t HZWE DATA UNDEFINED t LZWE HIGH-Z t SD DIN t HD DATAIN VALID CE_WR2.eps Notes: 1. The internal write time is defined by the overlap of CE LOW and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the Write. 2. I/O will assume the High-Z state if OE > VIH. 14 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® AC WAVEFORMS WRITE CYCLE NO. 3 (WE Controlled: OE is LOW During Write Cycle) t WC ADDRESS VALID ADDRESS OE LOW CE LOW t HA t AW t PWE2 WE t SA DOUT DATA UNDEFINED t HZWE t LZWE HIGH-Z t SD DIN t HD DATAIN VALID CE_WR3.eps Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 15 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® DATA RETENTION SWITCHING CHARACTERISTICS Symbol Parameter Test Condition Min. Max. Unit VDR VDD for Data Retention See Data Retention Waveform 1.2 3.6 V IDR Data Retention Current VDD = 1.2V, CE ≥ VDD – 0.2V — — 25 60 3 mA tSDR tRDR Data Retention Setup Time See Data Retention Waveform 0 — ns Recovery Time See Data Retention Waveform tRC — ns Ind. Auto. typ.(1) Note: 1. Typical values are measured at VDD = 3.0V, TA = 25oC and not 100% tested. DATA RETENTION WAVEFORM (CE Controlled) tSDR Data Retention Mode tRDR VDD 1.65V 1.4V VDR CE GND 16 CE ≥ VDD - 0.2V Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 IS61WV20488ALL IS61WV20488BLL IS64WV20488BLL ISSI ® ORDERING INFORMATION Industrial Range: -40°C to +85°C Voltage Range: 2.4V to 3.6V Speed (ns) 1 10 (8 ) Order Part No. Package IS61WV20488BLL-10MI IS61WV20488BLL-10MLI IS61WV20488BLL-10TI IS61WV20488BLL-10TLI 48 mini BGA (9mm x 11mm) 48 mini BGA (9mm x 11mm), Lead-free TSOP (Type II) TSOP (Type II), Lead-free Note: 1. Speed = 8ns for VDD = 3.3V + 5%. Speed = 10ns for VDD = 2.4V to 3.3V. Industrial Range: -40°C to +85°C Voltage Range: 1.65V to 2.2V Speed (ns) 20 Order Part No. Package IS61WV20488ALL-20MI IS61WV20488ALL-20TI 48 mini BGA (9mm x 11mm) TSOP (Type II) Automotive Range: -40°C to +125°C Voltage Range: 2.4V to 3.6V Speed (ns) 10 Order Part No. Package IS64WV20488BLL-10MA3 48 mini BGA (9mm x 11mm) IS64WV20488BLL-10TA3 TSOP (Type II) Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. 00C 01/09/06 17 ISSI PACKAGING INFORMATION ® Mini Ball Grid Array Package Code: M (48-pin) Top View Bottom View φ b (48x) 1 2 3 4 5 6 6 A D 5 4 3 2 1 A e B B C C D D D1 E E F F G G H H e E E1 A2 A SEATING PLANE Notes: 1. Controlling dimensions are in millimeters. A1 Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. D 01/15/03 ISSI PACKAGING INFORMATION ® Mini Ball Grid Array Package Code: M (48-pin) mBGA - 6mm x 8mm MILLIMETERS INCHES Sym. Min. Typ. Max. Min. Typ. Max. N0. Leads 48 A — — 1.20 .— — 0.047 A1 0.25 — 0.40 0.010 — 0.016 A2 0.60 — — 0.024 — D 7.90 8.00 8.10 0.311 0.314 0.319 5.60BSC 0.220BSC E 5.90 6.00 6.10 0.232 0.236 0.240 E1 4.00BSC 0.157BSC e 0.80BSC 0.031BSC D1 b 0.40 0.45 0.50 — 0.016 0.018 0.020 mBGA - 7.2mm x 8.7mm mBGA - 9mm x 11mm MILLIMETERS INCHES Sym. Min. Typ. Max. Min. Typ. Max. N0. Leads 48 MILLIMETERS INCHES Sym. Min. Typ. Max. Min. Typ. Max. N0. Leads 48 A — — 1.20 — — 0.047 A A1 0 .24 — 0.30 0.009 — 0.012 A1 A2 0.60 — — 0.024 — — A2 D 8.60 8.70 8.80 D 10.90 11.00 11.10 0.429 0.433 0.437 5.25BSC 0.207BSC D1 0.339 0.343 0.346 — — 1.20 — — 0.047 0.24 — 0.30 0.60 — — 0.009 — 0.012 0.024 — — 5.25BSC 0.207BSC E 7.10 7.20 7.30 0.280 0.283 0.287 E E1 3.75BSC 0.148BSC E1 3.75BSC 0.148BSC e 0.75BSC 0.030BSC e 0.75BSC 0.030BSC 0.012 0.014 0.016 b b 2 0.30 0.35 0.40 D1 8.90 0.30 9.00 0.35 9.10 0.40 0.350 0.354 0.358 0.012 0.014 0.016 Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. D 01/15/03 ISSI ® PACKAGING INFORMATION Plastic TSOP Package Code: T (Type II) N N/2+1 E1 1 Notes: 1. Controlling dimension: millimieters, unless otherwise specified. 2. BSC = Basic lead spacing between centers. 3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package. 4. Formed leads shall be planar with respect to one another within 0.004 inches at the seating plane. E N/2 D SEATING PLANE A ZD . b e Symbol Ref. Std. No. Leads A A1 b C D E1 E e L ZD α Millimeters Min Max Inches Min Max (N) 32 — 1.20 — 0.047 0.05 0.15 0.002 0.006 0.30 0.52 0.012 0.020 0.12 0.21 0.005 0.008 20.82 21.08 0.820 0.830 10.03 10.29 0.391 0.400 11.56 11.96 0.451 0.466 1.27 BSC 0.050 BSC 0.40 0.60 0.016 0.024 0.95 REF 0.037 REF 0° 5° 0° 5° L α A1 Plastic TSOP (T - Type II) Millimeters Inches Min Max Min Max 44 — 1.20 — 0.047 0.05 0.15 0.002 0.006 0.30 0.45 0.012 0.018 0.12 0.21 0.005 0.008 18.31 18.52 0.721 0.729 10.03 10.29 0.395 0.405 11.56 11.96 0.455 0.471 0.80 BSC 0.032 BSC 0.41 0.60 0.016 0.024 0.81 REF 0.032 REF 0° 5° 0° 5° Millimeters Min Max C Inches Min Max 50 — 1.20 0.05 0.15 0.30 0.45 0.12 0.21 20.82 21.08 10.03 10.29 11.56 11.96 0.80 BSC 0.40 0.60 0.88 REF 0° 5° — 0.047 0.002 0.006 0.012 0.018 0.005 0.008 0.820 0.830 0.395 0.405 0.455 0.471 0.031 BSC 0.016 0.024 0.035 REF 0° 5° Copyright © 2003 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. F 06/18/03