KINGBRIGHT AM27ID03

SUBMINIATURE SOLID STATE LAMP
AM27ID03
HIGH EFFICIENCY RED
Description
Features
The High Efficiency Red source color devices are made with
SUBMINIATURE PACKAGE.
Gallium Arsenide Phosphide on Gallium Phosphide Orange
GULL WING.
LONG LIFE - SOLID STATE RELIABILITY.
Light Emitting Diode.
LOW PACKAGE PROFILE.
PACKAGE :1000PCS / REEL.
RoHS COMPLIANT.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. Specifications are subject to change without notice.
SPEC NO: DSAB1967
REV NO: V.3
DATE: MAR/08/2005
PAGE: 1 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.CHENG
ERP: 1202000261
Selection Guide
Part No.
Dice
AM27ID03
Iv (mcd)
@ 20mA
Lens Type
HIGH EFFICIENCY RED (GaAsP/GaP)
Viewing
Angle
Min.
Typ.
2 θ 1/2
7
30
40°
RED DIFFUSED
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Device
Typ.
λpeak
Peak Wavelength
High Efficiency Red
λD
Dominant Wavelength
∆λ1/2
Max.
Units
Test Conditions
627
nm
IF=20mA
High Efficiency Red
625
nm
IF=20mA
Spectral Line Half-width
High Efficiency Red
45
nm
IF=20mA
C
Capacitance
High Efficiency Red
15
pF
VF=0V;f=1MHz
VF
Forward Voltage
High Efficiency Red
2.0
2.5
V
IF=20mA
IR
Reverse Current
High Efficiency Red
10
uA
VR = 5V
Absolute Maximum Ratings at TA=25°C
Parameter
High Efficiency Red
Units
Power dissipation
105
mW
DC Forward Current
30
mA
Peak Forward Current [1]
160
mA
5
V
Reverse Voltage
Operating/Storage Temperature
-40°C To +85°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
SPEC NO: DSAB1967
REV NO: V.3
DATE: MAR/08/2005
PAGE: 2 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.CHENG
ERP: 1202000261
High Efficiency Red
AM27ID03
SPEC NO: DSAB1967
REV NO: V.3
DATE: MAR/08/2005
PAGE: 3 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.CHENG
ERP: 1202000261
AM27ID03
Recommended Soldering Pattern
(Units : mm)
Tape Specifications
(Units : mm)
Remarks:
If there is sorting requirement (eg. forward voltage, luminous intensity or wavelength), the condition as follows:
1.Wavelength: +/-1nm (Test condition is based on the sorting standard).
2.Luminous intensity: +/-15% (Test condition is based on the sorting standard).
3.Forward voltage: +/-0.1V (Test condition is based on the sorting standard).
SPEC NO: DSAB1967
REV NO: V.3
DATE: MAR/08/2005
PAGE: 4 OF 4
APPROVED: J. Lu
CHECKED: Allen Liu
DRAWN: Y.CHENG
ERP: 1202000261