MX23L12854 128M-BIT Low Voltage, Serial Mask ROM Memory with 50MHz SPI Bus Interface FEATURES DESCRIPTION • • • • The MX23L12854 is a 128Mbit (16M x 8) Serial Mask ROM accessed by a high speed SPI-compatible bus. 128Mbit of Mask ROM 3.0 to 3.6V Single Supply Voltage SPI Bus Compatible Serial Interface 50MHz Clock Rate (maximum) PIN DESCRIPTION PIN CONFIGURATIONS 16-PIN SOP (300 mil) HOLD# VCC NC NC NC NC S# Q 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 SYMBOL C D Q S# HOLD# VCC VSS C D NC NC NC NC VSS NC DESCRIPTION Serial Clock Serial Data Input Serial Data Output Chip Select Hold Supply Voltage Ground Note: 1. NC=No Connection 2. See page 16 (onwards) for package dimensions, and how to identify pin-1. ORDER INFORMATION Part No. MX23L12854MC-20G Speed 20ns Package 16-SOP P/N: PM1141 1 Remark Pb-free REV. 1.1, MAY. 04, 2005 MX23L12854 MEMORY ORGANIZATION The memory is organized as: - 16M bytes (8 bits each) BLOCK DIAGRAM HOLD# Control Logic S# C D I/O Shift Register Q Address Register and Counter 512 Byte Data Buffer Y Decoder Size of the read-only memory area X Decoder P/N: PM1141 2 REV. 1.1, MAY. 04, 2005 MX23L12854 SIGNAL DESCRIPTION Serial Data Output (Q). This output signal is used to transfer data serially out of the device. Data is shifted out on the falling edge of Serial Clock (C). device is deselected. Driving Chip Select (S#) Low enables the device, placing it in the active power mode. After Power-up, a falling edge on Chip Select (S#) is required prior to the start of any instruction. Serial Data Input (D). This input signal is used to transfer data serially into the device. It receives instructions, addresses, and the data to be programmed. Values are latched on the rising edge of Serial Clock (C). Hold (HOLD#). The Hold (HOLD#) signal is used to pause any serial communications with the device without deselecting the device. Serial Clock (C). This input signal provides the timing of the serial interface. Instructions, addresses, or data present at Serial Data Input (D) are latched on the rising edge of Serial Clock (C). Data on Serial Data Output (Q) changes after the falling edge of Serial Clock (C). During the Hold condition, the Serial Data Output (Q) is high impedance, and Serial Data Input (D) and Serial Clock (C) are Don't Care. Chip Select (S#). When this input signal is High, the To start the Hold condition, the device must be selected, with Chip Select (S#) driven Low. P/N: PM1141 3 REV. 1.1, MAY. 04, 2005 MX23L12854 SPI MODES These devices can be driven by a microcontroller with its SPI peripheral running in either of the two following modes: the falling edge of Serial Clock (C). - CPOL=0, CPHA=0 - CPOL=1, CPHA=1 The difference between the two modes, as shown in Figure 2, is the clock polarity when the bus master is in Stand-by mode and not transferring data: For these two modes, input data is latched in on the rising edge of Serial Clock (C), and output data is available from - C remains at 0 for (CPOL=0, CPHA=0) - C remains at 1 for (CPOL=1, CPHA=1) Figure 1. Bus Master and Memory Devices on the SPI Bus SDO SPI Interface with (CPOL, CPHA) = (0, 0) or (1, 1) SDI SCK C Q D C Q D C Q D SPI Memory Device SPI Memory Device SPI Memory Device Bus Master (ST6, ST7, ST9, ST10, Others) CS3 CS2 CS1 S# HOLD# S# HOLD# S# HOLD# Note: 1. Hold (HOLD#) signals should be driven, High or Low as appropriate. Figure 2. SPI Modes Supported CPOL CPHA 0 0 C 1 1 C D MSB Q MSB P/N: PM1141 4 REV. 1.1, MAY. 04, 2005 MX23L12854 OPERATING FEATURES Active Power, Stand-by Power The Hold condition starts on the falling edge of the Hold (HOLD) signal, provided that this coincides with Serial Clock (C) being Low (as shown in Figure 3). When Chip Select (S#) is Low, the device is enabled, and in the Active Power mode. When Chip Select (S#) is High, the device is disabled, but could remain in the Active Power mode until all internal cycles have completed. The device then goes in to the Stand-by Power mode. The device consumption drops to ICC1 . The Hold condition ends on the rising edge of the Hold (HOLD#) signal, provided that this coincides with Serial Clock (C) being Low. If the falling edge does not coincide with Serial Clock (C) being Low, the Hold condition starts after Serial Clock (C) next goes Low. Similarly, if the rising edge does not coincide with Serial Clock (C) being Low, the Hold condition ends after Serial Clock (C) next goes Low. (This is shown in Figure 2). Protection Modes The environments where non-volatile memory devices are used can be very noisy. No SPI device can operate correctly in the presence of excessive noise. To help combat this, the MX23L12854 boasts the following data protection mechanisms: During the Hold condition, the Serial Data Output (Q) is high impedance, and Serial Data Input (D) and Serial Clock (C) are Don't Care. - Power-On Reset and an internal timer (tPUW) can provide protection against inadvertant changes while the power supply is outside the operating specification. Normally, the device is kept selected, with Chip Select (S#) driven Low, for the whole duration of the Hold condition. This is to ensure that the state of the internal logic remains unchanged from the moment of entering the Hold condition. Hold Condition The Hold (HOLD#) signal is used to pause any serial communications with the device without resetting the clocking sequence. If Chip Select (S#) goes High while the device is in the Hold condition, this has the effect of resetting the internal logic of the device. To restart communication with the device, it is necessary to drive Hold (HOLD#) High, and then to drive Chip Select (S#) Low. This prevents the device from going back to the Hold condition. To enter the Hold condition, the device must be selected, with Chip Select (S#) Low. Figure 3. Hold Condition Activation (for data output only) C HOLD# Q2 Q Q0 Q2 Q1 Q3 Q4 Q5 C HOLD# Q2 Q Q0 Q1 Q2 P/N: PM1141 5 Q3 Q4 Q5 Q6 REV. 1.1, MAY. 04, 2005 MX23L12854 INSTRUCTIONS All instructions, addresses and data are shifted in and out of the device, most significant bit first. Every instruction sequence starts with a one-byte instruction code. Depending on the instruction, this might be followed by address bytes, or by data bytes, or by both or none. Serial Data Input (D) is sampled on the first rising edge of Serial Clock (C) after Chip Select (S#) is driven Low. Then, the one-byte instruction code must be shifted in to the device, most significant bit first, on Serial Data Input (D), each bit being latched on the rising edges of Serial Clock (C). In the case of a Read Data Bytes (READ), Read Data Bytes at Higher Speed (Fast_Read), the shifted-in instruction sequence is followed by a data-out sequence. Chip Select (S#) can be driven High after any bit of the data-out sequence is being shifted out. The instruction set is listed in Table 1. Table 1. Instruction Set Instruction READ FAST_READ Description One-byte Instruction Code Address Bytes Dummy Bytes Data Bytes Read Data Bytes 0000 0011 03h 3 0 1 to ∞ Read Data Bytes at Higher Speed 0000 1011 0Bh 3 1 1 to ∞ P/N: PM1141 6 REV. 1.1, MAY. 04, 2005 MX23L12854 Figure 4. Read Data Bytes (READ) Instruction Sequence and Data-Out Sequence S# 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 32 33 34 35 36 37 38 39 C Instruction 24-Bit Address 23 22 21 D 3 2 1 0 MSB Data Out 1 High Impedance 7 Q 6 5 4 3 2 Data Out 2 1 0 7 MSB Read Data Bytes (READ) The device is first selected by driving Chip Select (S#) Low. The instruction code for the Read Data Bytes (READ) instruction is followed by a 3-byte address (A23-A0), each bit being latched-in during the rising edge of Serial Clock (C). Then the memory contents, at that address, is shifted out on Serial Data Output (Q), each bit being shifted out, at a maximum frequency fR, during the falling edge of Serial Clock (C). The instruction sequence is shown in Figure 4. The first byte addressed can be at any location. The address is automatically incremented to the next higher address after each byte of data is shifted out. The whole memory can, therefore, be read with a single Read Data Bytes (READ) instruction.When the highest address is reached, the address counter rolls over to 000000h, allowing the read sequence to be continued indefinitely. The Read Data Bytes (READ) instruction is terminated by driving Chip Select (S#) High. Chip Select (S#) can be driven High at any time during data output. P/N: PM1141 7 REV. 1.1, MAY. 04, 2005 MX23L12854 Figure 5. Read Data Bytes at Higher Speed (FAST_READ) Instruction Sequence and Data-Out Sequence S# 0 1 2 3 4 5 6 7 8 9 10 28 29 30 31 C Instruction 24 BIT ADDRESS D Q 23 22 21 3 2 1 0 High Impedance S# 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 C Dummy Byte D 7 6 5 4 3 2 1 0 DATA OUT 2 DATA OUT 1 Q 7 6 5 4 3 2 1 0 7 MSB MSB 6 5 4 3 2 1 0 7 MSB automatically incremented to the next higher address after each byte of data is shifted out. The whole memory can, therefore, be read with a single Read Data Bytes at Higher Speed (FAST_READ) instruction. When the highest address is reached, the address counter rolls over to 000000h, allowing the read sequence to be continued indefinitely. Read Data Bytes at Higher Speed (FAST_READ) The device is first selected by driving Chip Select (S#) Low. The instruction code for the Read Data Bytes at Higher Speed (FAST_READ) instruction is followed by a 3byte address (A23-A0) and a dummy byte, each bit being latched-in during the rising edge of Serial Clock (C). Then the memory contents, at that address, is shifted out on Serial Data Output (Q), each bit being shifted out, at a maximum frequency fC, during the falling edge of Serial Clock (C). The Read Data Bytes at Higher Speed (FAST_READ) instruction is terminated by driving Chip Select (S#) High. Chip Select (S#) can be driven High at any time during data output. The instruction sequence is shown in Figure 5. The first byte addressed can be at any location. The address is P/N: PM1141 8 REV. 1.1, MAY. 04, 2005 MX23L12854 POWER-UP AND POWER-DOWN If the delay, tVSL, has elapsed, after VCC has risen above VCC (min), the device can be selected for READ instructions even if the tPUW delay is not yet fully elapsed. At Power-up and Power-down, the device must not be selected (that is Chip Select (S#) must follow the voltage applied on VCC ) until VCC reaches the correct value: At Power-up, the device is in the following state: - The device is in the Standby mode. - VCC(min) at Power-up, and then for a further delay of tVSL - VSS at Power-down Usually a simple pull-up resistor on Chip Select (S#) can be used to insure safe and proper Power-up and Powerdown. Normal precautions must be taken for supply rail decoupling, to stablise the VCC feed. Each device in a system should have the VCC rail decoupled by a suitable capacitor close to the package pins. To avoid data corruption and inadvertent write operations during power up, a Power On Reset (POR) circuit is included. The logic inside the device is held reset while VCC is less than the POR threshold value, VWI -- all operations are disabled, and the device does not respond to any instruction. (Generally, this capacitor is of the order of 0.1uF). At Power-down, when VCC drops from the operating voltage, to below the POR threshold value, VWI , all operations are disabled and the device does not respond to any instruction. These values are specified in Table 2. Figure 6. Power-up Timing VCC VCC(max) Chip Selection Not Allowed VCC(min) tVSL Reset State of the Device Read Access allowed Device fully accessible VWI tPUW time P/N: PM1141 9 REV. 1.1, MAY. 04, 2005 MX23L12854 Table 2. Power-Up Timing Symbol tVSL1 Parameter Min. VCC(min) to S# low Max. Unit 30 us Note: 1. These parameters are characterized only. MAXIMUM RATING Stressing the device above the rating listed in the"Absolute Maximum Ratings" table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Table 3. Absolute Maximum Ratings Symbol Parameter TSTG Storage Temperature TLEAD Lead Temperature during Soldering 1 Min. Max. Unit - 65 150 ˚C 260 2 ˚C VIO Input and Output Voltage (with respect to Ground) - 0.6 4.0 V VCC Supply Voltage - 0.6 4.0 V VESD Electrostatic Discharge Voltage (Human Body model) 3 - 2000 2000 V Note: 1. Compliant with the ECOPACK ® 7191395 specifiication for lead-free soldering processes 2. Not exceeding 250˚C for more than 30 seconds, and peaking at 260˚C 3. JEDEC Std JESD22-A114A (C1=100 pF, R1=1500 Ω, R2=500 Ω) P/N: PM1141 10 REV. 1.1, MAY. 04, 2005 MX23L12854 DC AND AC PARAMETERS tables that follow are derived from tests performed under the Measurement Conditions summarized in the relevant tables. Designers should check that the operating conditions in their circuit match the measurement conditions when relying on the quoted parameters. This section summarizes the operating and mea-surement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC Characteristic Table 4. Operating Conditions Symbol VCC TA Parameter Min. Max. Unit Supply Voltage 3.0 3.6 V Ambient Operating Temperature - 40 85 ˚C Min. Max. Unit Table 5. AC Measurement Conditions Symbol CL Parameter Load Capacitance 30 Input Rise and Fall Times pF 5 ns Input Pulse Voltages 0.2VCC to 0.8VCC V Input Timing Reference Voltages 0.3VCC to 0.7VCC V V CC / 2 V Output Timing Reference Voltages Note: 1. Output Hi-Z is defined as the point where data out is no longer driven. Figure 7. AC Measurement I/O Waveform Input Levels Input and Output Timing Reference Levels 0.8VCC 0.7VCC 0.5VCC 0.3VCC 0.2VCC Table 6. Capacitance Symbol COUT CIN Parameter Output Capacitance (Q) Input Capacitance (other pins) Test Condition Min. Max. Unit VOUT = 0V 8 pF VIN = 0V 6 pF Note: Sampled only, not 100% tested, at TA=25˚C and a frequency of 20 MHz. P/N: PM1141 11 REV. 1.1, MAY. 04, 2005 MX23L12854 Table 7. DC Characteristics Symbol Parameter Test Condition (in addition to those in Table 8) Min. Max. Unit ILI Input Leakage Current ±2 uA ILO Output Leakage Current ±2 uA ICC1 Standby Current S # = VCC, VIN = VSS or VCC 50 uA C = 0.1VCC / 0.9.VCC at 50MHz, Q = open 8 mA C = 0.1VCC / 0.9.VCC at 20MHz, Q = open 4 mA ICC2 Operating Current (READ) VIL Input Low Voltage - 0.5 0.3VCC V VIH Input High Voltage 0.7VCC VCC+0.4 V VOL Output Low Voltage IOL = 1.6mA 0.4 V VOH Output High Voltage IOH = -100 uA P/N: PM1141 12 VCC- 0.2 V REV. 1.1, MAY. 04, 2005 MX23L12854 Table 8. AC Characteristics Test conditions specified in Table 4 and Table 5 Symbol Alt. fC fC fR Parameter Min. Typ. Max. Unit Clock Frequency for the following instructions: FAST_READ D.C. 50 MHz Clock Frequency for READ instructions D.C. 20 MHz tCH 1 tCLH Clock High Time 9 ns tCL 1 tCLL Clock Low Time 9 ns tCLCH 2 Clock Rise Time3 (peak to peak) 0.1 V/ns tCHCL 2 Clock Fall Time3 (peak to peak) 0.1 V/ns S# Active Setup Time (relative to C) 5 ns S# Not Active Hold Time (relative to C) 5 ns tSLCH tCSS tCHSL tDVCH tDSU Data In Setup Time 2 ns tCHDX tDH Data In Hold Time 5 ns tCHSH S# Active Hold Time (relative to C) 5 ns tSHCH S# Not Active Setup Time (relative to C) 5 ns 100 tSHSL tCSH S# Deselect Time tSHQZ 2 tDIS Output Disable Time 8 ns tCLQV tV Clock Low to Output Valid 8 ns tCLQX tHO ns Output Hold Time 0 ns tHLCH HOLD# Setup Time (relative to C) 5 ns tCHHH HOLD# Hold Time (relative to C) 5 ns tHHCH HOLD Setup Time (relative to C) 5 ns tCHHL HOLD Hold Time (relative to C) 5 ns tHHQX 2 tLZ HOLD to Output Low-Z 8 ns tHLQZ 2 tHZ HOLD# to Output High-Z 8 ns Note: 1. tCH + tCL must be greater than or equal to 1/ fC 2. Value guaranteed by characterization, not 100% tested in production. 3. Expressed as a slew-rate. P/N: PM1141 13 REV. 1.1, MAY. 04, 2005 MX23L12854 Figure 8. Serial Input Timing tSHSL S# tCHSL tSLCH tCHSH tSHCH C tDVCH tCHCL tCHDX tCLCH LSB IN MSB IN D High Impedance Q Figure 9. Hold Timing S# tHLCH tCHHL tHHCH C tCHHH tHLQZ tHHQX Q D HOLD# P/N: PM1141 14 REV. 1.1, MAY. 04, 2005 MX23L12854 Figure 10. Output Timing S# tCH C tCLQV tCLQX tCL tCLQV tSHQZ tCLQX LSB OUT D tQLQH tQHQL Q ADDR.LSB IN P/N: PM1141 15 REV. 1.1, MAY. 04, 2005 MX23L12854 PACKAGE INFORMATION P/N: PM1141 16 REV. 1.1, MAY. 04, 2005 MX23L12854 REVISION HISTORY Revision Description 1.0 1. Added "Order Information" 1.1 1. Changed VCC from "2.7V to 3.6V" to "3.0V to 3.6V" P/N: PM1141 17 Page P1 P1,11 Date APR/06/2005 MAY/04/2005 REV. 1.1, MAY. 04, 2005 MX23L12854 MACRONIX INTERNATIONAL CO., LTD. HEADQUARTERS: TEL:+886-3-578-6688 FAX:+886-3-563-2888 EUROPE OFFICE: TEL:+32-2-456-8020 FAX:+32-2-456-8021 JAPAN OFFICE: TEL:+81-44-246-9100 FAX:+81-44-246-9105 SINGAPORE OFFICE: TEL:+65-348-8385 FAX:+65-348-8096 TAIPEI OFFICE: TEL:+886-2-2509-3300 FAX:+886-2-2509-2200 MACRONIX AMERICA, INC. TEL:+1-408-453-8088 FAX:+1-408-453-8488 CHICAGO OFFICE: TEL:+1-847-963-1900 FAX:+1-847-963-1909 http : //www.macronix.com MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.