TH8065 Voltage Regulator with LIN Transceiver and Watchdog Features o o Compatible to LIN Specification 2.0 and SAE J2602 Operating voltage VS = 6 ... 18 V o Low standby current consumption of typ. 15 μA in sleep mode “noload” current < 200µA Linear low drop voltage regulator 5V/70mA ±2% Output current limitation LIN-Bus Transceiver Compatible to ISO9141 functions Baud rate up to 20 kBaud Slew rate control for best EME behavior Low slew mode for optimized SAE J2602 transmission High EMI immunity High signal symmetry for using in RC – based slave nodes up to 2% clock tolerance Current limitation Wake-up via LIN bus traffic Reset output (default 8ms/4.65V) Reset time adjustable to 4ms, 15ms and 30ms during IC final test Analogue Watchdog with programmable time constant via external capacity Over temperature shutdown Automotive temperature range of –40°C to 125°C CMOS compatible interface to microcontroller Load dump protected (40V) Small SOIC14 package with fused lead frame for low Rth value o o o o o o o o o o Ordering Information Part No. Temperature Range Package Version POR time TH8065 KDC AA K (-40 to 125 °C) DC (SOIC14NB) A A (8ms) On Request TH8065 KDC AB TH8065 KDC AC TH8065 KDC AD K (-40 to 125 °C) K (-40 to 125 °C) K (-40 to 125 °C) DC (SOIC14NB) DC (SOIC14NB) DC (SOIC14NB) A A A B (4ms) C (30ms) D (15ms) General Description The TH8065 consists of a low-drop voltage regulator 5V/70mA combined with a Reset/Watchdog unit and a LIN bus transceiver. The LIN transceiver is suitable for LIN bus systems conform to LIN specification revision 2.0 and SAE J2602. The combination of voltage regulator and bus transceiver makes it possible to develop simple, but powerful and cheap slave nodes in LIN Bus systems. TH8065 – Datasheet 3901008065 Page 1 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog Contents 1. Functional Diagram ............................................................................................................................... 4 2. Electrical Specification.......................................................................................................................... 5 2.1 Operating Conditions ....................................................................................................................................... 5 2.2 Absolute Maximum Ratings ............................................................................................................................. 5 2.3 Static Characteristics ....................................................................................................................................... 6 2.3.1. Voltage Regulator and Reset Unit .......................................................................................................... 6 2.3.2. LIN Bus Interface.................................................................................................................................... 8 2.4 Dynamic Characteristics .................................................................................................................................. 9 2.5 Timing Diagrams ............................................................................................................................................ 11 3. Functional Description ........................................................................................................................ 13 3.1 Operating Modes............................................................................................................................................ 13 3.2 Initialization .................................................................................................................................................... 15 3.3 Wake-Up ........................................................................................................................................................ 15 3.4 VSUP under voltage reset.............................................................................................................................. 16 3.5 Overtemperature Shutdown ........................................................................................................................... 16 3.6 LIN BUS Transceiver ..................................................................................................................................... 17 3.7 Linear Regulator............................................................................................................................................. 20 3.8 RESET and Watchdog ................................................................................................................................... 21 3.8.1. RESET.................................................................................................................................................. 21 3.8.2. Watchdog ............................................................................................................................................. 22 3.9 Mode Input EN ............................................................................................................................................... 24 4. Application Hints ................................................................................................................................. 26 4.1 4.2 4.3 4.4 4.5 5. Safe Operating Area ...................................................................................................................................... 26 Low Dropout Regulator .................................................................................................................................. 27 Application Circuitry ....................................................................................................................................... 29 EMI Supressing.............................................................................................................................................. 29 Connection to Flash-MCU .............................................................................................................................. 30 Operating during Disturbance............................................................................................................ 31 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 Operating without VSUP or GND ................................................................................................................... 31 Short Circuit BUS against VBAT .................................................................................................................... 31 Short Circuit BUS against GND...................................................................................................................... 31 Short Circuit TxD against GND ...................................................................................................................... 31 TxD open ....................................................................................................................................................... 31 Short Circuit VCC against GND ..................................................................................................................... 31 Overload of VCC ............................................................................................................................................ 31 Undervoltage VCC ......................................................................................................................................... 31 Undervoltage VSUP ....................................................................................................................................... 32 Short circuit RxD, RESET against GND or VCC ............................................................................................ 32 Short circuit CWD against GND or VCC ........................................................................................................ 32 6. PIN Description .................................................................................................................................... 33 7. Mechanical Specification .................................................................................................................... 34 8. Tape and Reel Specification ............................................................................................................... 35 8.1 8.2 9. Tape Specification.......................................................................................................................................... 35 Reel Specification .......................................................................................................................................... 36 ESD/EMC Remarks .............................................................................................................................. 37 9.1 9.2 9.3 General Remarks ........................................................................................................................................... 37 ESD-Test ....................................................................................................................................................... 37 EMC ............................................................................................................................................................... 37 10. Revision History................................................................................................................................... 38 11. Assembly Information ......................................................................................................................... 39 12. Disclaimer............................................................................................................................................. 40 TH8065 – Datasheet 3901008065 Page 2 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog List of Figures Figure 1 - Block diagram.......................................................................................................................... 4 Figure 2 - Timing diagram for propagation delays................................................................................. 11 Figure 3 - Timing diagram for duty cycle acc. to LIN 2.0 and J2602..................................................... 11 Figure 4 - Timing Diagram for EN mode selection ................................................................................ 12 Figure 5 - State diagram of operating modes........................................................................................ 13 Figure 6 - Operating of power-on and under-voltage reset ................................................................... 15 Figure 7 - Receive mode impulse diagram............................................................................................ 17 Figure 8 - TxD input circuitry ................................................................................................................. 18 Figure 9 - RxD output circuitry............................................................................................................... 19 Figure 10 - Characteristic of current limitation VCC = f (IVCC) ............................................................... 20 Figure 11 - Reset and Watchdog behaviour.......................................................................................... 21 Figure 12 - Reset behaviour .................................................................................................................. 22 Figure 13 - Output current of reset output vs. VCC voltage .................................................................. 22 Figure 14 - Watchdog timing ................................................................................................................. 23 Figure 15 - EN input circuitry ................................................................................................................. 24 Figure 16 - EN controlled via MCU........................................................................................................ 24 Figure 17 - Permanent normal mode..................................................................................................... 25 Figure 18 - Power dissipation LIN transceiver @ 20kbit ....................................................................... 26 Figure 19 - Save operating area............................................................................................................ 27 Figure 20 - ESR Curves for 6.8μF ≤ CL ≤ 100μF and Frequency of 100 kHz ....................................... 28 Figure 21 - Application circuit (slave node) ........................................................................................... 29 Figure 22 – Example circuitry for connection of RxD to MCU for flash programming........................... 30 TH8065 – Datasheet 3901008065 Page 3 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 1. Functional Diagram VSUP VCC Vaux control amplifier Aux. Supply Adjust ment EN ⎠ μs SBY MR Mode Control Reset PORTimer Osc VCC POR 4.65 V VBAT_Res Vaux Wake-up Control RESETBuffer WDI_sig RESET WD logic VBAT_Res WDI_sig VBATReset Vaux Wake-Filter 50k Receiver VSUP MR 4,8,15,30ms VCC CWD comp POR 4.65 V Temp. Protection SBY TSHD Vaux WDI Reset Generator VBG BG CWD GND current limitation VSUP 70μs RxDBuffer Vaux VCC RxD Rec-Filter 30k Transmitter BUS GND VCC SBY Driver control 15k Filter TxD MR Figure 1 - Block diagram TH8065 – Datasheet 3901008065 Page 4 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 2. Electrical Specification All voltages are referenced to ground (GND). Positive currents flow into the IC. The absolute maximum ratings (in accordance with IEC 134) given in the table below are limiting values that do not lead to a permanent damage of the device but exceeding any of these limits may do so. Long term exposure to limiting values may affect the reliability of the device. Correct operating of the device cannot be guaranteed if any of these limits are exceeded. 2.1 Operating Conditions Parameter Symbol Min Max Unit Supply voltage VSUP 6 18 V Output voltage VCC 4.85 5.15 V Operating ambient temperature TA -40 +125 °C Junction temperature TJ +150 °C 2.2 Absolute Maximum Ratings Parameter Supply voltage at VSUP Input voltage at pin BUS Symbol Condition VSUP VBUS Min Max -1.0 18 T ≤ 300 s - 30 T ≤ 500 ms - 40 -24 30 - 40 T ≤ 500 ms Unit V V Difference VSUP-VCC VSUP-VCC -0.3 40 V Input voltage at pin EN VINEN -0.3 VSUP+0.3 V Input voltage at pin TxD, RxD, RESET, WDI, CWD VIN -0.3 VCC+0.3 V Input current at pin EN, TxD, RxD, RESET, WDI, CWD IIN -25 25 mA IINSH -500 500 mA Input current for short circuit of pin VSUP and VCC ESD Capability on pin BUS, VBAT, GND ESDBUSHB Human body Model, 100pF via 1.5kΩ -4 4 kV ESD Capability on pin TxD, RxD, EN, RESET, WDI, CWD, VCC ESDBUSHB Human body Model, 100pF via 1.5kΩ -2 2 kV Power dissipation Thermal resistance from junction to ambient (SOIC14fused) [2] Junction temperature [3] Storage temperature [1] [2] [3] P0 Internal limited [1] RTHJA 70 K/W TJ 150 °C 150 °C TSTG -55 See chapter 4.1 Safe Operating Area SOIC14 with fused lead frame and an active copper area of >150sqmm See chapter 3.5 Overtemperature Shutdown TH8065 – Datasheet 3901008065 Page 5 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 2.3 Static Characteristics Unless otherwise specified all values in the following tables are valid for VSUP = 6 to 18V and TAMB = -40 to 125oC. All voltages are referenced to ground (GND), positive currents flow into the IC. 2.3.1. Voltage Regulator and Reset Unit Parameter Symbol Condition Min Typ Max Unit T[1] 6 12 18 V B VEN = VSUP = 13V, CWD=1nF, BUS: 1k to VSUP, Pins TxD, RxD, WDI and RESET open, EN = VCC 200 300 μA A VSUP = 13V, VEN = 0V, BUS: 1k to VSUP 15 30 μA A VSUP Operating voltage Supply current, VCC „noload“ [2] VSUP ISnl Supply current, „sleep mode“ ISsleep VSUP under voltage reset “off” threshold VSUVR_OFF VSUP ramp up 3.2 3.7 4.2 V A VSUP under voltage reset “on” threshold VSUVR_ON VSUP ramp down 2.7 3.1 3.5 V A VSUP under voltage reset hysteresis VSUVR_HYS V A V A 5.25 V A 0.2 VCC VCCn 6V ≤ VSUP ≤ 18V 1mA ≤ ILOAD ≤ 70mA TA = 25°C TA = -40°C to 125°C Output voltage VCC 4.90 4.85 5.0 5.10 5.15 VCCh 18V ≤ VSUP ≤ 40V ILOAD = 10mA VD10 IVCC = 10mA 75 120 mV A VD30 IVCC = 30mA 220 350 mV A VD70 IVCC = 70mA 500 800 mV A VLNR 6V ≤ VSUP ≤ 18V 20 mV A VLDR10 ILOAD = 1mA Æ 10mA 50 mV A VLDR30 ILOAD = 1mA Æ 30mA 90 mV A VLDR70 ILOAD = 1mA Æ 70mA 150 mV A Output current limitation IVCC_max VSUP > 0V 200 mA A Ripple Rejection on VSUP PSRR VSUP = 12V, fi = 120Hz, ViP-P = 1V, ILOAD = 10mA Drop-out voltage [3] Line regulation Load regulation TH8065 – Datasheet 3901008065 Page 6 of 40 4.80 80 130 t.b.d dB May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog Parameter Symbol Reset threshold - POR VRES(ON) Reset threshold – low voltage reset VRES(OFF) Vres Hysteresis VRESHYS = |VRES(ON) – VRES(OFF)| VRESHYS Master reset threshold Condition Min Typ Max VCC ramp up, t > trr 4.4 4.6 4.8 V A VCC ramp down, t > trr 4.4 4.6 4.8 V A 150 mV A 3.3 V D VMRES 3.0 3.15 Unit T[1] Enable Input EN Input voltage low VENL -0.3 0.8 V A Input voltage high VENH 2.0 VSUP +0.3 V A Hysteresis VENHYS 50 300 mV A Pull-down resistor EN low RpdENL 0V ≤ VEN ≤ 0.8V 14 25 35 kΩ A Pull-down current EN high IpdENH VEN ≥ VENL 0.5 2 10 µA A 0.8 V A Output RESET Output voltage low Pull-up current VOL1_RESET IOUT = 1 mA, VSUP ≥ 6 V Ipu -500 -375 -250 μA A Input CWD Input threshold low VCWDL 0.076 0.08 0.084 VCC A Input threshold high VCWDH 0.342 0.36 0.378 VCC A Pull up current (charge current) ICWD_pu VIN = 1V 7.6 13.9 20.2 µA A Pull down current (discharge current) ICWD_pd VIN = 1V 0.76 1.39 2.02 µA A 35 50 73 kΩ A 0.3 VCC A VCC A °C D °C D Input WDI Pull down resistor Rpd_WDI Input voltage low VIL_WDI Input voltage high VIH_WDI VIN = VCC 0.7 Thermal Protection Thermal shutdown TJSHD 155 Thermal recovery TJREC 126 [1] [2] [3] 180 A = 100% serial test, B = Operating parameter, C = Only used for data characterization (cpk), D = Value guaranteed by design No active watchdog reset The nominal VCC voltage is measured at VSUP =12V. If the VCC voltage is 100mV below its nominal value then the voltage drop is VD = VSUP – VCC. TH8065 – Datasheet 3901008065 Page 7 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 2.3.2. LIN Bus Interface Parameter Symbol Condition Min Typ Max Unit T[1] General 20 μA A 47 kΩ A mA A 20 µA A -1 1 mA A 0.4 0.6 Pull up current BUS (recessive) IINBUSpu VBUS = 18 V, VSUP = 6V Pull up resistor BUS RBUSpu VSUP = 12V, VBUS = 0V 20 Reverse current BUS (recessive) -IINBUSrev VSUP = 12V, VBUS = 0V -1 Reverse current BUS (loss of battery) IINBUS_lob VSUP = 0V, 0V ≤ VBUS ≤ 18V Reverse current BUS (loss of ground) IINBUS_log VSUP= 12V, 0V ≤ VBUS ≤ 18V 30 Receiver Receive threshold Vthr_rec, Vthr_dom Centre point of receive threshold Vthr_cnt = (Vthr_rec+Vthr_dom)/2 Vthr_cnt Hysteresis of receive threshold Vthr_hys = Vthr_rec-Vthr_dom Vthr_hys 7.0 V ≤ VSUP ≤ 18 V 0.475 A 0.5 0.525 VSUP A 0.15 0.175 A Transmitter Output voltage BUS (dominant) Current limitation BUS VBUSdom_1 ILIM IBUS = 40mA VBUS = VSUP, TxD = 0V 1.2 V A 41 120 200 mA A 9.5 15 21 kΩ A 0.3 VCC A Input TxD Pull-up resistor Rpu_TxD Input voltage low TxD VIL Input voltage high TxD VIH VIN = 0V VCC A 0.7 Output RxD Output voltage Low RxD VOL IOUT = 1 mA Output voltage High RxD VOH IOUT = -1 mA [1] 0.8 VCC - 0.8 V A V A A = 100% serial test, B = Operating parameter, C = only used for data characterization (cpk), D = Value guaranteed by design TH8065 – Datasheet 3901008065 Page 8 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 2.4 Dynamic Characteristics 6V ≤ VSUP ≤ 18V, -40°C ≤ TA ≤ 125°C, unless otherwise specified Min Typ Max Unit T[1] VSUP = 12V,Vers. “A” 5.6 8 10.4 ms A VSUP = 12V,Vers. “B” 2.8 4 5.2 ms A VSUP = 12V,Vers. “C” 21 30 39 ms A VSUP = 12V,Vers. “D” 10.5 15 19.5 ms A trr VSUP = 12V 3.0 6.5 12 μs A Discharge time CWD-capacity tfCWD CWD = 10nF, ΔVCWD = 1V 5 µs C Watchdog period tWD_per CWD = 1nF ±1% 0.63 1.1 1.54 ms A Watchdog reset time tWD_R CWD = 1 nF ±1% 60 100 140 µs A twake_BUS 30 70 150 μs A tdeb_EN 2 6 15 µs D Parameter Symbol Condition RESET and Watchdog Reset time Reset rising time tRes Wake-up and Mode Select Wake up time Debouncing time EN Propagation delay EN to sleep mode tpd_EN_sleep EN = High to Low 400 µs A Propagation delay EN to normal mode tpd_EN_norm EN = Low to High 400 µs A Setup time TxD to EN for low slew mode tset_TxD_LS TxD = Low before EN = L/H 5 µs B Hold time TxD after EN for low slew mode thold_TxD_LS TxD = Low after EN = L/H 20 µs B General LIN Parameter Slew rate rising edge BUS dV/dTrise Normal Mode 0.8 1.5 2.5 V/µs C Slew rate falling edge BUS dV/dTfall BUS-Load: 1kOhm/1nF -2.5 -1.5 -0.8 V/µs C Slew rate rising edge BUS dV/dTrise 0.3 0.8 1.3 V/µs C Slew rate falling edge BUS dV/dTfall -1.3 -0.8 -0.3 V/µs C Receiver debouncing time tdeb_BUS 1.5 2.8 4.0 µs C 6 µs A 2 µs A 35 pF D Receiver propagation delay BUS->RxD Symmetry propagation delay BUS->RxD Internal capacity TH8065 – Datasheet 3901008065 tdr_RxD tdf_RxD tdsym_RxD CBUS Low Slew Mode BUS-Load: 1kOhm/1nF CL(RXD) = 50 pF tdr_RXD - tdf_RXD Pulse at BUS via 10kOhm with 0/10 V; VSUP = open Page 9 of 40 -2 25 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog Parameter Symbol Condition Min Typ Max Unit T[1] LIN transceiver parameter according to LIN Physical Layer Spec. rev. 2.0, table 3.4 (20kbit/s) Conditions: Normal slew mode; VSUP =7.0V to 18V; BUS loads: 1kΩ/1nF; 660Ω/6.8nF; 500Ω/10nF TxD signal: tBit = 50µs, twH = TwL = tBit; trise = tfall < 100ns Minimal recessive bit time [2] trec(min) 40 50 58 µs Maximum recessive bit time [2] trec(max) 40 50 58 µs Duty cycle 1 D1 D1 = trec(min) / (2*tBit) Duty cycle 2 D2 D2 = trec(max) / (2*tBit) 0.396 A 0.581 A LIN transceiver parameter according to LIN Physical Layer Spec. rev. 2.0, table 3.4 (10.4kbit/s) Conditions: Low slew mode; VSUP =7.0V to 18V; BUS loads: 1kΩ/1nF; 660Ω/6.8nF; 500Ω/10nF TxD signal: tBit = 96µs, twH = TwL = tBit; trise = tfall < 100ns Minimal recessive bit time [2] Maximum recessive bit time [2] trec(min) 80 96 113 µs trec(max) 80 96 113 µs Duty cycle 1 D1 D1 = trec(min) / (2*tBit) Duty cycle 2 D2 D2 = trec(max) / (2*tBit) 0.417 A 0.590 A LIN transceiver parameter according to SAE J2602 (10.4kbit/s) Conditions: Low slew mode; VSUP =7.0V to 18V; BUS loads: 1kΩ/1nF;660Ω/6.8nF;500Ω/10nF TxD signal: tBit = 96µs, twH = TwL = tBit; trise = tfall < 100ns Minimal recessive delay TxD -> BUS [2] Maximum recessive delay TxD -> BUS Minimal dominant delay TxD -> BUS [2] [2] Maximum dominant delay TxD -> BUS [2] tx_rec_min 48 µs tx_rec_max 48 µs tx_dom_min 48 µs tx_dom_max 48 µs Maximum rec. to dom. delay Tr_d_max tx_rec_max - tx_dom_min 15.9 µs A Maximum dom. to rec. delay Td_r_max tx_dom_max - tx_rec_min 17.2 µs A [1] [2] A = 100% serial test, B = Operating parameter, C = only used for data characterization (cpk), D = Value guaranteed by design See chapter 2.5 Timing Diagrams TH8065 – Datasheet 3901008065 Page 10 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 2.5 Timing Diagrams 50% TxD tdf_TXD tdr_TXD VBUS 100% 95% BUS 50% 50% 5% 0% tdr_RXD tdf_RXD RxD 50% Figure 2 - Timing diagram for propagation delays tBit tBit TxD tx_rec_max tx_dom_max tx_dom_min VSUP 100% tdom(max) 74.4% (77.8%) tdom(min) 58.1% (61.6%) BUS 58.1% (61.6%) 42.2% (38.9%) 28.4% (25.1%) VSS trec(min) tx_rec_min trec(max) 28.4% (25.1%) 0% Remark: The levels for low slope mode are shown in brackets Figure 3 - Timing diagram for duty cycle acc. to LIN 2.0 and J2602 TH8065 – Datasheet 3901008065 Page 11 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog Normal Mode Sleep Mode Normal Mode Ini-Phase Low Slew tpdEN_sleep 5V 4.5V VCC 0.5V 0V tset_TxD_LS tpdEN_norm EN 2V 2.0V 0.8V thold_TxD_LS TxD 50% Figure 4 - Timing Diagram for EN mode selection TH8065 – Datasheet 3901008065 Page 12 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 3. Functional Description The TH8065 consists of a low drop voltage regulator 5V/70mA and a LIN bus transceiver, which is a bidirectional bus interface for data transfer between LIN bus and the LIN protocol controller. Additionally integrated is a RESET unit with a power-on-reset delay of 8ms (optional 4,15 or 30ms). and a programmable watchdog time which will be defined by an external capacity. 3.1 Operating Modes The TH8065 provides three main operating modes “normal”, “sleep” and “low slew” and the intermediate states “Ini-state” and “thermal shutdown”. The main modes are fixed states defined by basic actions (VSUP start, EN or wake-up). The intermediate states are soft states. They aren’t defined by logical actions but by changes of voltage (VSUP, VCC) or junction temperature. VSUP power on Set Slew_State = L UVR / POR VSUP > UVR_OFF Regulator on RESET = L / after tres RESET=H and Watchdog activated Wake-up disabled LIN-Transceiver on/ normal slew mode clear Reset-Timer Start Regulator -> VCC ramp up RESET = L Wake-up disabled VCC > Vres (4.65V) & Slew_State=L VSUP < UVR_ON Ini-state EN= L/H edge & TxD=H NormalMode VCC < Vres Tj > Tjshd VCC > Vres (4.65V) & Slew_State=H VSUP < UVR_ON thermal shutdown EN= L/H edge & TxD=L VSUP > UVR_ON & BUS Wake-up Tj > Tjshd Tj < Tjrec Tj > Tjshd VCC < Vres Regulator off Wake-up disabled LIN-Transceiver off EN= H/L EN=L Low Slew Mode SleepMode EN= H/L Regulator off Thermal shutdown off Wake-up enabled (LIN-Receiver on) LIN-Transmitter off Regulator on RESET = L / after tres RESET=H and Watchdog activated Wake-up disabled Set Slew State = H LIN-Transceiver on/ low slew mode Figure 5 - State diagram of operating modes TH8065 – Datasheet 3901008065 Page 13 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog Normal Mode This mode is the base mode. The bus transceiver is able to send with a max baud rate of 20kbit/s. The whole TH8065 is active. Switching to normal mode can be done via the following actions: - Start of VSUP or after under voltage reset - Rising edge at EN (EN=high) and TxD=high (local wake-up) - Activity on the LIN bus (remote wake-up) Sleep Mode Sleep mode is most current saving. With a falling edge on EN (EN=low) the TH8065 is switched from normal mode into sleep mode. The voltage regulator and the reset/watchdog unit will be switched off and the LIN transceiver is in recessive state. Switching into sleep mode can be done independently from the current transceiver state. That means if the transmitter is in dominant state this state will be cancelled and it will be switched to recessive state. Low Slew Mode In this mode the slew rate is switched from the normal value of typ. 1.6V/µs to a low value of typ. 0.8V/µs. This mode is optimized to send with a maximum baud rate of 10.4kbit/s (SAE J2602). Because of this reduction of the slew rate the EME behaviour is improved especially in the frequency range of 100 kHz to 10MHz. Switching to this mode is possible with a combination of rising edge on EN together with a low level on TxD. POR-state This is the power-on-reset state of the TH8065, while Vsup < VSUVR_OFF. If the prior state was sleep mode, the TH8065 switches via the ini-state to normal mode. Ini-state This is an intermediate state, which will pass through after switching on of VSUP or VCC. The TH8065 remains in this state if VCC is below VRES (Reset output = L) and Vsup > VSUVR_ON. Thermal Shutdown If the junction temperature TJ is higher than TJSHD (>155°C), the TH8065 will be switched into the thermal shutdown mode. The behaviour within this mode is comparable with the sleep mode except for LIN transceiver operating. The transceiver is completely disabled; no wake-up functionality is available. If TJ falls below the thermal recovery temperature TJREC (typ. 140°C) the TH8065 will be recover to the previous state (normal, sleep or low slew). TH8065 – Datasheet 3901008065 Page 14 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 3.2 Initialization Initialization starts if the power supply is switched on as well as every rising edge on of the TH8065 via the EN pin. VSUP- Power-ON If VSUP is switched on the TH8065 starts to normal mode via the POR- and Ini-state. A combination of dynamic POR and under voltage reset circuitry generates a POR signal, which switches the TH8065 into normal mode. This power on behaviour is independent from the status of the EN-pin. Power-on reset and under-voltage reset operates independent from each other, which secures the independence from the rise time of VSUP. During fast VSUP edges the power-on reset will be active. If the increasing of VSUP is very slow (> 1ms/V) and VSUP > VSUVR_OFF (typ. 3.5V) the under voltage reset unit initializes the voltage regulator. The effects of both POR circuits at different VSUP slopes will show in Figure 6. VSUP VSUVR_OFF VSUVR_ON UVR POR POR UVR EN=H/L VCC normal mode sleep mode normal mode Figure 6 - Operating of power-on and under-voltage reset After POR the voltage regulator starts and the VCC voltage will be output. If VCC>VMRes the bus interface will be activated. If the VCC voltage level is higher than VRES, the reset time tRes is started. After tRes the RESET output switches from low to high (see Figure 12). The Initialization procedure operates after POR independent from the EN voltage. Start of Linear Regulator via Wake-up The initialization is only being done for the VCC circuitry parts. This procedure begins with leaving the master reset state (VCC > VMRes) and runs in the same manner as the VSUP-Power-On. 3.3 Wake-Up If the regulator is put into sleep mode it can be woken up with the BUS interface. Every pulse on the BUS (high pulse or low pulse) with a pulse width of min. 70μs switches on the regulator. The low slew mode has to be selected again if necessary. After the BUS has woken up the regulator, it can only be switched off with a high level followed by a low level on the EN pin. TH8065 – Datasheet 3901008065 Page 15 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 3.4 VSUP under voltage reset The under voltage detection unit inhibits an undefined behaviour of the TH8062 under low voltage condition (VSUP < 4V). If VSUP drops below VSUVR_ON (typ. 3.1V) the under voltage detection becomes active and the IC will be switched to POR state. The following increasing of VSUP above VSUVR_OFF (typ. 3.7V) cancels this POR state and the voltage regulator starts with the initialization sequence. VSUP under voltage in Normal Mode Supply Voltages below VSUVR_OFF do not influence the voltage regulator. The output voltage Vcc follows VSUP. VSUP under voltage in Sleep Mode No exit from the sleep mode will take place if the VSUP voltage drops down to VSUVR_ON (typ. 3.5V). The under voltage reset becomes active (POR-state) if the voltage drops below 2.7V. As a result of this functioning, the sleep mode is left to the normal mode. If VSUP rises again above VSUVR_OFF (typ. 4.2V) the IC initializes the voltage regulator and continues to work with the normal mode. The under voltage reset unit secures stable functioning in the under voltage range of VSUP down to GND level. The dynamic Power-On-Reset secures a defined internal state independent from the duration of the VSUP drop, which guarantees a stable restart. VSUP under voltage in Low Slew Mode The behaviour of TH8062 at low VSUP voltages is equal to the sleep mode. The low slew mode will be cancelled, if VSUP drops below VSUVR_ON in this mode. The TH8062 enters the normal mode, if VSUP rises again above VSUVR_OFF. 3.5 Overtemperature Shutdown If the junction temperature is 155°C < TJ < 175°C the over-temperature recognition will be activated and the regulator voltage will be switched off. The VCC voltage drops down, the reset state is entered and the bustransceiver is switched off (recessive state). After TJ falls below 140°C the TH8065 will be initialized again (see Figure 12). This initialisation starts independently from the voltage levels on EN and BUS. Within the thermal shutdown mode the transceiver can not switch to the normal mode neither with local nor with remote wake-up. The operation of the TH8065 is possible between TAmax (125°C) and the switch off temperature, but small parameter differences can appear. After over-temperature switch-off the IC behaves as described in chapter 3.8 RESET and Watchdog. TH8065 – Datasheet 3901008065 Page 16 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 3.6 LIN BUS Transceiver The TH8065 has an integrated bi-directional bus interface device for data transfer between LIN bus and the LIN protocol controller. The transceiver consists of a driver with slew rate control, wave shaping and current limitation and a receiver with high voltage comparator followed by a debouncing unit. Transmit Mode During transmission the data at the pin TxD will be transferred to the BUS driver to generate a bus signal. To minimize the electromagnetic emission of the bus line, the BUS driver has an integrated slew rate control and wave shaping unit. Transmitting will be interrupted in the following cases: - Sleep mode - Thermal Shutdown active - Master Reset (VCC < 3.15V) The recessive BUS level is generated from the integrated 30k pull up resistor in serial with an active diode This diode prevents the reverse current of VBUS during differential voltage between VSUP and BUS (VBUS>VSUP). No additional termination resistor is necessary to use the TH8065 in LIN slave nodes. If this IC is used for LIN master nodes it is necessary that the BUS pin is terminated via an external 1kΩ resistor in series with a diode to VBAT. Receive Mode The data signals from the BUS pin will be transferred continuously to the pin RxD. Short spikes on the bus signal are suppressed by the implemented debouncing circuit (τ = 2.8µs). VSUP Vthr_max 60% BUS Vthr_hys 50% 40% Vthr_cnt Vthr_min t < tdeb_BUS t < tdeb_BUS RxD Figure 7 - Receive mode impulse diagram The receive threshold values Vthr_max and Vthr_min are symmetrical to the centre voltage of 0.5*VSUP with a hysteresis of 0.150*VSUP. Including all tolerances the LIN specific receive threshold values of 0.4*VSUP and 0.6*VSUP will be securely observed. TH8065 – Datasheet 3901008065 Page 17 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog Slew Modes and Data rates The TH8065 is a constant slew rate transceiver which means that the bus driver works with a mode depended slew rate. In normal mode the slew rate is typical 1.6 V/µs and in low slew mode typical 0.8 V/µs. The lower slew rate in low slew mode associated with a baud rate of 10.4kbit/s improves the EME behaviour. The LIN transceiver of TH8065 is compatible to the physical layer specification according to LIN 2.0 specification for data rates up to 20kbit/s and the SAE specification J2602 for data rates up to 10.4kbit/s. The constant slew rate principle is very robust against voltage drops and can operate with RC- oscillator systems with a clock tolerance up to ±2% between 2 nodes. Low Slew Mode In this mode the slew rate is switched from the normal value of typ. 1.6V/µs to a low value of typ. 0.8V/µs. This mode is optimized to send with a maximum baud rate of 10.4kbit/s (acc. to SAE J2602). Because of this reduction of the slew rate the EME behaviour is improved especially in the frequency range of 100 kHz to 10MHz. Input TxD The 5V input TxD controls directly the BUS level: TxD = low TxD = high -> -> BUS = low (dominant level) BUS = high (recessive level) The TxD pin has an internal pull up resistor connected to VCC. This guarantees that an open TxD pin generates a recessive BUS level. MCU VCC VCC RPU_TXD IPU_TXD TH8065 Typ. 15k TxD RC-Filter (10ns) Figure 8 - TxD input circuitry TH8065 – Datasheet 3901008065 Page 18 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog Output RxD The received BUS signal will be output to the RxD pin: BUS < Vthr_cnt – 0.5 * Vthr_hys BUS > Vthr_cnt + 0.5 * Vthr_hys -> -> RxD = low RxD = high This output is a push-pull driver between VCC and GND with an output current of 1mA. TH8065 MCU VCC RxD Figure 9 - RxD output circuitry TH8065 – Datasheet 3901008065 Page 19 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 3.7 Linear Regulator The TH8065 has an integrated low drop linear regulator with a p-channel-MOSFET as driving transistor. This regulator outputs a voltage of 5V ±3% and a current of ≤70mA within an input voltage range of 6V ≤ VSUP ≤ 18V. The current limitation unit limits the output current for short circuits or overload to 130mA respectively drop-down of the VCC voltage. 6 VCC [V] 5 4 3 2 1 0 0 20 40 60 80 100 120 140 Iload [mA] Figure 10 - Characteristic of current limitation VCC = f (IVCC) TH8065 – Datasheet 3901008065 Page 20 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 3.8 RESET and Watchdog The TH8065 contains a combined reset- and watchdog-unit which secures the correct initialization and generation of the reset signal. VSUP, VCC VRES int. POR signal trr tRes RESET Start-up ON delay Watchdog Power-off WDI CWD VCWDH tWDL tWDH VCWDL Figure 11 - Reset and Watchdog behaviour The RESET pin outputs the reset state and the watchdog state of the TH8065. The POR timer will be started if VSUP is switched on and VCC> POR threshold (4.65V). The Watchdog is inactive. After the time tRes the RESET output is switched from low to high and the watchdog becomes active. The charging of the watchdog capacity starts and dependent from the trigger pulse on the WDI input the Reset outputs the status of the watchdog. The watchdog is only active if VCC > VRES. If VCC drops below VRES the watchdog will be switched off and the watchdog capacity will be discharged. 3.8.1. RESET The RESET unit combines a VCC low voltage detection unit with fixed POR timer This output is switched from low to high if VSUP is switched on and VCC>VRES (4.65V) after the time tRes . All conditions which cause a drop of the VCC voltage will be detected from the low voltage reset unit which generates a reset signal. The TH8065 will be reinitialized if the VCC voltage rises above the low voltage limit. If the voltage VCC drops below VRES then the RESET output is switched from high to low after the time trr has been reached. For this reason short breaks of the VCC voltage and uncontrolled reset generations will be inhibited. The circuitry of the RESET output driver guarantees, that the reset low level during decreasing of the VCC voltage will be secure kept (see Figure 13). TH8065 – Datasheet 3901008065 Page 21 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog VSUP T>Tj T<Tj t<trr VCC t<trr VRES tRes trr tRes tRes tRes RESET Initialisation Thermal shutdown Spike VSUP Current limitation Low voltage active VSUP Spike VCC Figure 12 - Reset behaviour Figure 13 - Output current of reset output vs. VCC voltage 3.8.2. Watchdog The Watchdog can be used for observation of the connected microcontroller. It has to be triggered via the WDI input and the time is defined via the capacity connected to the CWD input. The watchdog status will be output via the reset pin. With rising edges on WDI the watchdog time will be reset. If the WDI input isn’t triggered the internal circuitry generates low pulses at the RESET pin with a time tWD_R and a period of tWD-per. The CWD capacitor provides a wide adjustment range for the watchdog time. With every rising edge on WDI the capacitor CWD will be charged up to the threshold VCWDL. If there is no new trigger pulse on WDI, the following discharging of CWD within the time tWDL will be done up to the lower threshold VCWDL. TH8065 – Datasheet 3901008065 Page 22 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog WDI WDI = High or Low tWDt_R CWD tWD_per VCWDH VCWDM VCWDL tWD_R RESET Figure 14 - Watchdog timing The reset output will be switched from high to low (watchdog reset), if the voltage on pin CWD reaches VCWDL. The reset output stays at low level until the voltage at CWD has reached the level of VCWDH. The RESET pin generates a periodic signal with low pulse width of tWD_R and a period of tWD_per, if no retrigger of WDI takes place. Calculation of Watchdog time Watchdog reset time: tWD _ R = (VCWDH − VCWDL ) ∗ CWD I CWD _ pu CWD Watchdog capacity connected to pin CWD VCWDH Upper watchdog threshold VCWDL Lower watchdog threshold Max. watchdog reset trigger time tWDt _ R = (VCWDH − VCWDL ) ∗ CWD ICWD _ pd ICWD_pu CWD charge current ICWD_pd CWD discharge current With the valid charge and discharge currents of CWD of the TH8065 is a simple calculation of the capacity values for a defined watchdog trigger time and reset time possible: tWDt _ R [ms ] = CWD [nF ] tWD _ R [ms ] = 0.1 ∗ CWD [nF ] Example: C WD = 10nF → t WDt _ R = 10ms and t WD _ R = 1ms Within a timeframe of 10ms the MCU has to reset the watchdog to prevent a reset generation. The complete watchdog period tWD_per = 11ms. If the watchdog has to be deactivated for e.g. firmware development, the pin CWD has to be directly connected to GND. The reset signal is in this case only determined by the reset thresholds. TH8065 – Datasheet 3901008065 Page 23 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 3.9 Mode Input EN The TH8065 is switched into the sleep mode with a falling edge and into normal mode with a rising edge at the EN pin. The normal mode will be kept as long as EN = high. The deactivation of TH8065 with a falling edge at EN can be done independently from the state of the bustransceiver. Filter 6μs 23k ESD enable 1.5M voltage limiter EN Figure 15 - EN input circuitry The maximum input voltage is VSUP. The threshold is typ. 1.4V and therefore also 5V and 3.3V CMOS levels can be used as input signal. Figure 15 shows the internal circuitry of the EN pin. The EN input has an internal pull down resistor of typ. 23k to secure that if this pin is not connected a low level will be generated. An input debouncing filter of 6µs suppresses effectively disturbance couplings via the EN pin It will use different pull down resistors for normal and sleep mode to minimize the sleep mode current. The wide input voltage range allows different EN control possibilities. If the EN input is connected to a CMOS output of the MCU, a falling edge switches the TH8065 into sleep mode (the regulator is also switched off). The wake up is only possible via the bus line. TH8065 VBAT GND GND VSUP VCC EN CIN LIN 220p Cload MCU +5V RESET GND TxD BUS RxD CWD WDI GND GND Figure 16 - EN controlled via MCU TH8065 – Datasheet 3901008065 Page 24 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog If the application doesn’t need the wake up capability of the TH8065 a direct connection EN to VSUP is possible. In this case the TH8065 operates in permanent normal mode. Also possible is the external (outside of the module) control of the EN line via a VBAT signal. If this is a direct VBAT signal an external reverse battery protection has to be added to the circuitry. TH8065 VBAT CIN 10k LIN 220p GND GND VSUP VCC EN Cload MCU +5V RESET GND TxD BUS RxD CWD WDI GND GND Figure 17 - Permanent normal mode TH8065 – Datasheet 3901008065 Page 25 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 4. Application Hints 4.1 Safe Operating Area The maximum power dissipation depends on the thermal resistance of the package and the PCB, the temperature difference between Junction and Ambient as well as the airflow. The power dissipation can be calculated with: PD = (VSUP – VCC) * IVCC + PD_TX The power dissipation of the transmitter PD_TX depends on the transceiver configuration and its parameters as well as on the bus voltage VBUS=VBAT-VD, the resulting termination resistance RL, the capacitive bus load CL and the bit rate. Figure 18 shows the dependence of power dissipation of the transmitter as function of VSUP. The conditions for calculation of the power dissipation is RL=500Ω, CL=10nF, bit rate=20kbit and duty cycle on TxD of 50% 50 45 40 PD [mW] 35 30 25 20 15 10 5 0 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 VSUP [V] Figure 18 - Power dissipation LIN transceiver @ 20kbit The permitted package power dissipation can be calculated: PDmax = T j − TA RTHJ − A If we consider that PD_TX_max= f (VSUP) the max output current IVCC on VCC can be calculated: T j − TA I VCCmax = RTHJ − A − PD _ TX _ max @ VSUP VSUP − VCC TJ -TA is the temperature difference between junction and ambient and Rth is the thermal resistance of the package. The thermal energy is transferred via the package and the pins to the ambient. This transfer can be improved with additional ground areas on the PCB as well as ground areas under the IC. TH8065 – Datasheet 3901008065 Page 26 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 80 maximum current 70 TA=85°C TA=125°C 50 max. supply voltage IVCC_max [mA] 60 40 30 20 10 0 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 VSUP [V] Figure 19 - Save operating area The linear regulator of the TH8065 operates with input voltages up to 18V and can output a current of 70mA. The maximum power dissipation limits the maximum output current at high input voltages and high ambient temperatures. The output current of 70mA at an ambient temperature of TA = 125°C is only possible with small voltage differences between VSUP and VCC. See Figure 19 for safe operating areas for different ambient temperatures. The TH8065 is able to output 70mA over the whole voltage range if the max ambient temperature is limited to 85°C. 4.2 Low Dropout Regulator The voltage regulator of theTH8065 is a low dropout regulator (LDO) with a p-MOSFET as driving transistor. This kind of regulator has a standard pole, generated from the internal frequency compensation and an additional pole, which is dependent from the load and the load capacitance. This additional pole can cause an instable behaviour of the regulator! It is required a zero point to compensate this additional pole. It can be realised via an additional load resistor in series with a load capacitor. It is used for this compensation the equivalent series resistance (ESR) of the load capacitor. Every real capacitor is characterized with an ESR value. With the help of this ESR value an additional zero point is implemented into the amplification loop and therefore the result of the negative phase shift is compensated. Because of this correlation the regulator has a stable operating area which is defined by the load resistance RL, the load capacitor CL and the corresponding ESR value. The load resistance resp. load current is defined by the application itself and therefore the compensation of the pole can only be done via variation of the load capacitance and ESR value. Input Capacitor on VSUP CIN An input capacitance is necessary of CIN ≥ 4.7µF. Higher capacitance values improves the line transient response and the supply noise rejection behaviour. The combination of electrolytic capacitor (e.g.100µF) in parallel with a ceramic RF-capacitor (e.g.100nF) archives good disturbance suppressing. The input capacitor should be placed as close as possible (< 1cm) to the VSUP pin. TH8065 – Datasheet 3901008065 Page 27 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog Load Capacitor on VCC CL The regulator is stabilized by the output capacitor CL. The TH8065 requires a minimum of 4.7µF capacitor connected to the 5V output to insure stability. This capacitor should maintain its ESR in the stable region of the ESR curve (See Figure 20) over the full operating temperature range of the application. It has to be taken into account that the capacitance value and the ESR of a capacitor changes with temperature. The minimal capacitance value must also be kept within the whole operating temperature range. ESR@100kHz [Ohm] 100 10 1 Stable Area 0,1 0,01 0 10 20 30 40 50 load current [mA] Figure 20 - ESR Curves for 6.8μF ≤ CL ≤ 100μF and Frequency of 100 kHz The value and type of the output capacitor can be selected using the diagram shown in Figure 20. The load capacitor should be placed as close as possible (< 1cm) to the VCC pin. Capacitance Value The capacitance value of an electrolytic capacitor is dependent from the voltage, temperature and the frequency. The temperature coefficient of the capacitor value is positive, that means that the value increases with increasing of the temperature. The capacitance value decreases with increasing of the frequency. This behaviour of a capacitor can cause that at TA=-40°C the capacitance value falls below the minimum required capacitance for the regulator. In this case the regulator becomes instable, which means the regulator starts oscillation. The nominal value of the capacitor at TA=25°C has to be chosen with enough margin under consideration of the capacitor specification. The instable behaviour will be amplified because of the decreasing of the capacitance with this oscillation. ESR The equivalent serial resistance is the resistor part of the equivalent circuit diagram of a capacitor. The ESR value is dependent from the temperature and frequency. Normally the specified ESR values for a capacitor is valid at a temperature of TA=25°C and a frequency of f=100 kHz. The temperature coefficient is negative, which means with increasing of the temperature the ESR value decreases. In the choice of the capacitance has to be taken into account that the ESR can decrease at TA=40°C dramatically that the valid operating area can be left, which causes that the regulator will be instable. TH8065 – Datasheet 3901008065 Page 28 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog Tantalum Capacitors This type of capacitor has a low dependence of the capacitance and the ESR from the temperature and is therefore well suited as VCC load capacitor. Aluminium Capacitors These capacitors show a strong influence of the capacitance and the ESR from the temperature. This characteristic restrains the usability as load capacitor for the low drop regulator of TH8065. 4.3 Application Circuitry TH8065 GND VBAT VSUP CIN 100μ EN 100n LIN-BUS 220p CWD 10μ...100μ MCU GND VCC 100n RESET GND TxD BUS RxD CWD WDI GND GND +5V RST Figure 21 - Application circuit (slave node) 4.4 EMI Supressing To minimize the influence of EMI on the bus line a 220pF capacitor should be connected directly to the BUS pin (see Figure 21). This EMI-Filter makes sure that the RF injections into the IC from the BUS line have no affect resp. will be limited. Alternatively to a pure C-filter it is also possible to use LC- or RC-filter. The dimension of C, L or R, L depends on the corner frequency, the maximum LIN bus capacitance (10nF) and the compliance with the DC- and AC LIN bus parameters. TH8065 – Datasheet 3901008065 Page 29 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 4.5 Connection to Flash-MCU While programming a flash MCU the TH8065 should be disconnected from the MCU. This can be done via disconnecting the supply voltage from the TH8065 or by switching off with the EN pin. The reverse current supply of the IC via the RxD pin, if the connected MCU pin is used as normal signal input and programming input, must be inhibited via a decoupling diode. In this case the MCU must be supplied via the programming interface. Prog.-Data 10u...47u MCU TH8065 VCC 47n...100n RESET TxD RxD Vhigh_RxD >= 4.7V at VCC = 5V Vlow_RxD = 0.8V 0.7V Vhigh = 4V at VCC = 5V Figure 22 – Example circuitry for connection of RxD to MCU for flash programming The programming of the Flash is also possible via the LIN pin, if the MCU supports this kind of flash mode. TH8065 – Datasheet 3901008065 Page 30 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 5. Operating during Disturbance 5.1 Operating without VSUP or GND The absence of VSUP or GND connection will not influence or disturb the communication between other bus nodes. No reverse supply of the IC can appear if without GND or VSUP connection the BUS pin is on VBAT level. 5.2 Short Circuit BUS against VBAT The reaction of the IC depends on the send state of the transceiver: - Recessive LIN bus is blocked, no influence to the TH8065 - Dominant Current limitation, thermal shut down of TH8065 if power dissipation will make an overrun of TJ 5.3 Short Circuit BUS against GND LIN bus is blocked. No influence on the TH8065. 5.4 Short Circuit TxD against GND The LIN transceiver is permanently in the dominant state, which means the whole LIN bus. This state can only be detected from the LIN controller. In this case the controller must switch off the LIN node via the EN input of the TH8065. A thermal shut down of TH8065 will appear if the power dissipation will make an overrun of TJ. 5.5 TxD open The internal pull-up resistor forces the LIN node to the recessive state. The communication between the other bus-nodes will not be disturbed. 5.6 Short Circuit VCC against GND The VCC pin is protected via a current limitation. This state is comparable with the behaviour in the sleep mode. 5.7 Overload of VCC Thermal switch off The power dissipation is increasing if the load current is between IVCC_max and ILVCC. If the max junction temperature of >155°C is reached, the IC will be switched off. The voltage regulator will also be switched off and a reset signal is forced. Over current If the current limitation is active the voltage on VCC drops down. If this voltage under-runs the threshold VRES, a reset will be forced. 5.8 Undervoltage VCC The reset unit ensures the correct behaviour of the driver during under-voltage. The BUS pin generates the recessive state if VCC < VMRes (3.15V). The inputs EN, WDI and TxD have pull-up or pull-down characteristics. If VCC ≥ VMRes the TxD signal is transmitted to the bus. The receive mode is also active. TH8065 – Datasheet 3901008065 Page 31 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 5.9 Undervoltage VSUP The combination of dynamic power on reset and low voltage reset guarantees a defined start up behaviour. If the supply voltage VSUP drops below 3V the low voltage detection becomes active. If the VSUP voltage rises again above 3.5V the low voltage reset will be terminated and the 5V voltage regulator will be started. 5.10 Short circuit RxD, RESET against GND or VCC Both outputs are short circuit proof to VCC and ground. 5.11 Short circuit CWD against GND or VCC The watchdog is deactivated if CWD is short circuit against GND. The reset signal is in this case only determined by the thresholds. If WDI is short circuit against VCC the reset pin outputs a permanent low level. TH8065 – Datasheet 3901008065 Page 32 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 6. PIN Description GND 1 14 GND VSUP 2 13 VCC EN 3 12 RESET GND 4 11 TxD BUS 5 10 RxD CWD 6 9 WDI GND 7 8 GND TH8065 SOIC14 Pin Name IO-Typ 1 GND P Ground 2 VSUP P Supply voltage 3 EN I Enable input voltage regulator, HV-pull-down-input, High-active 4 GND P Ground 5 BUS I/O LIN bus line 6 CWD I/O Watchdog capacity 7 GND P Ground 8 GND P Ground 9 WDI I Watchdog trigger input, pull down 10 RxD O Receive output, 5V-push-pull 11 TxD I 5V-Transmit input, pull-up-input 12 RESET O Reset 5V-output, active low 13 VCC O Regulator output 5V/70mA 14 GND P Ground TH8065 – Datasheet 3901008065 Description Page 33 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 7. Mechanical Specification SOIC14NB Small Outline Integrated Circiut (SOIC), SOIC 14, 150 mil A1 B D E e H h L A α ZD A2 8.56 8.74 3.81 3.99 1.27 5.80 6.20 0.25 0.50 0.41 1.27 1.52 1.72 0° 8° 0.51 1.37 1.57 0.337 0.344 0.160 0.167 0.050 0.228 0.244 0.010 0.020 0.016 0.050 0.060 0.068 0° 8° 0.020 0.054 0.062 C All Dimension in mm, coplanarity < 0.1 mm min max 0.10 0.25 0.36 0.45 0.19 0.25 All Dimension in inch, coplanarity < 0.004” min max 0.004 0.01 0.014 0.0075 0.018 0.0098 TH8065 – Datasheet 3901008065 Page 34 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 8. Tape and Reel Specification 8.1 Tape Specification max. 10° max. 10° IC pocket R Top View n. mi Sectional View T2 P0 D0 T P2 E G1 < A0 > F K0 W B0 B1 S1 G2 T1 P1 D1 Cover Tape Abwickelrichtung Standard Reel with diameter of 13“ Package Parts per Reel Width Pitch SOIC14NB 2500 16 mm 8 mm D0 E P0 P2 Tmax T1 max G1 min G2 min B1 max D1 min F P1 Rmin T2 max W 1.5 +0.1 1.75 ±0.1 4.0 ±0.1 2.0 ±0.1 0.6 0.1 0.75 0.75 12.1 1.5 7.5 ±0.1 4 - 12 ±0.1 30 8.0 16.0 ±0.3 A0, B0, K0 can be calculated with package specification. Cover Tape width 13.3 mm. TH8065 – Datasheet 3901008065 Page 35 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 8.2 Reel Specification W2 W1 B* D* C A N Amax B* C D*min 330 2.0 ±0.5 13.0 +0,5/-0,2 20.2 Width of half reel Nmin W1 W2 max 8 mm 100,0 8,4 11,1 TH8065 – Datasheet 3901008065 Page 36 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 9. ESD/EMC Remarks 9.1 General Remarks Electronic semiconductor products are sensitive to Electro Static Discharge (ESD). Always observe Electro Static Discharge control procedures whenever handling semiconductor products. 9.2 ESD-Test The TH8065 is tested according CDF-AEC-Q100-002 / MIL883-3015.7 (human body model). 9.3 EMC The test on EMC impacts is done according to ISO 7637-1 for power supply pins and ISO 7637-3 for dataand signal pins. TH8065 – Datasheet 3901008065 Page 37 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 10. Revision History Version Changes Remark 001 Preliminary Release Date Oct. 2004 002 Updated Static Characteristics April 2005 003 Introduction of variable POR Reset times May 2006 TH8065 – Datasheet 3901008065 Page 38 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 11. Assembly Information Standard information regarding manufacturability of Melexis products with different soldering processes Our products are classified and qualified regarding soldering technology, solderability and moisture sensitivity level according to following test methods: Reflow Soldering SMD’s (Surface Mount Devices) • • IPC/JEDEC J-STD-020 Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices (classification reflow profiles according to table 5-2) EIA/JEDEC JESD22-A113 Preconditioning of Nonhermetic Surface Mount Devices Prior to Reliability Testing (reflow profiles according to table 2) Wave Soldering SMD’s (Surface Mount Devices) and THD’s (Through Hole Devices) • • EN60749-20 Resistance of plastic- encapsulated SMD’s to combined effect of moisture and soldering heat EIA/JEDEC JESD22-B106 and EN60749-15 Resistance to soldering temperature for through-hole mounted devices Iron Soldering THD’s (Through Hole Devices) • EN60749-15 Resistance to soldering temperature for through-hole mounted devices Solderability SMD’s (Surface Mount Devices) and THD’s (Through Hole Devices) • EIA/JEDEC JESD22-B102 and EN60749-21 Solderability For all soldering technologies deviating from above mentioned standard conditions (regarding peak temperature, temperature gradient, temperature profile etc) additional classification and qualification tests have to be agreed upon with Melexis. The application of Wave Soldering for SMD’s is allowed only after consulting Melexis regarding assurance of adhesive strength between device and board. Melexis is contributing to global environmental conservation by promoting lead free solutions. For more information on qualification of RoHS compliant products (RoHS = European directive on the Restriction Of the Use of Certain Hazardous Substances) please visit the quality page on our website: http://www.melexis.com/quality_leadfree.asp TH8065 – Datasheet 3901008065 Page 39 of 40 May 2006 Rev 003 TH8065 Voltage Regulator with LIN Transceiver and Watchdog 12. Disclaimer Devices sold by Melexis are covered by the warranty and patent indemnification provisions appearing in its Term of Sale. Melexis makes no warranty, express, statutory, implied, or by description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. Melexis reserves the right to change specifications and prices at any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with Melexis for current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by Melexis for each application. The information furnished by Melexis is believed to be correct and accurate. However, Melexis shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interrupt of business or indirect, special incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of Melexis’ rendering of technical or other services. © 2002 Melexis NV. All rights reserved. For the latest version of this document. Go to our website at www.melexis.com Or for additional information contact Melexis Direct: Europe and Japan: Phone: +32 1367 0495 E-mail: [email protected] All other locations: Phone: +1 603 223 2362 E-mail: [email protected] ISO/TS16949 and ISO14001 Certified TH8065 – Datasheet 3901008065 Page 40 of 40 May 2006 Rev 003